Nissan Maxima. Manual — part 1218
ROAD WHEEL TIRE ASSEMBLY
WT-61
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
4. If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight sheets in line with each other as shown.
CAUTION:
Do not install one balance weight sheet on top another.
5. Start balancer machine again.
6. Install balance weight on inner side of road wheel in the bal-
ancer machine indication position (angle).
CAUTION:
Do not install more than two balance weights.
7. Start balancer machine. Make sure that inner and outer residual
imbalance values are 5 g (0.17 oz) each or below.
8. If either residual imbalance value exceeds 5 g (0.17 oz), repeat installation procedures.
TIRE ROTATION
• Use power tool to remove wheel and tire assembly.
• Follow the maintenance schedule for tire rotation service intervals.
Refer to
MA-5, "FOR USA AND CANADA : Explanation of General
(United States and Canada),
Explanation of General Maintenance"
(Mexico).
CAUTION:
• Do not include the T-type spare tire when rotating the tires.
• When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
• Be careful not to tighten wheel nut at torque exceeding the
criteria for preventing strain of disc rotor.
Wheel balance
Dynamic (At flange)
Static (At flange)
Maximum allowable im-
balance
Refer to
.
PEIA0033E
Wheel nut tightening
torque
: Refer to
.
SMA829C
WT-62
< UNIT REMOVAL AND INSTALLATION >
TRANSMITTER
UNIT REMOVAL AND INSTALLATION
TRANSMITTER
Exploded View
INFOID:0000000009466855
Removal and Installation
INFOID:0000000009466856
REMOVAL
1. Remove road wheel and tire assembly using power tool. Refer to
.
2. Remove valve cap and valve core to deflate the tire.
NOTE:
If the tire is to be reused, apply a matching mark on the tire in line with the position of the road wheel valve
stem assembly for the purpose of road wheel and tire balance adjustment after installation.
3. Remove the valve stem nut and allow transmitter to fall into tire.
4. Lubricate the tire outside bead well with a suitable non-silicone lubricant, and remove outside of tire from
the road wheel. Reach inside the tire and remove the transmitter.
CAUTION:
• Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and road wheel.
• Be sure not to damage the road wheel or transmitter.
• Do not allow lubricant to make contact with transmitter.
5. Lubricate the tire inside bead well with a suitable non-silicone lubricant, and remove inside of tire from the
road wheel.
1.
Transmitter (tire pressure sensor)
2.
O-ring
3.
Valve stem nut
4.
Valve core
5.
Valve cap
6.
Valve stem assembly
:
Parts that are replaced as a set when the tire is replaced.
AWEIA0212GB
SEIA0047E
TRANSMITTER
WT-63
< UNIT REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
CAUTION:
• Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and road wheel.
• Be sure not to damage the road wheel.
6. Remove the valve stem from the transmitter as shown.
INSTALLATION
1. Apply a suitable non-silicone lubricant to the tire inside bead.
CAUTION:
Do not use silicone lubricant. Use of silicone lubricant will deteriorate the tire and wheel.
2. Install the tire inside bead (1) onto the road wheel (2) in the posi-
tion shown.
3. Install the valve stem to the transmitter.
4. Install the O-ring to the transmitter.
CAUTION:
• Do not reuse O-ring
• Insert O-ring to the base of the transmitter.
• The base of the valve stem (A) must be positioned in the
groove of the metal plate as shown.
JSEIA0378ZZ
JPEIC0105ZZ
JSEIA0376GB
WT-64
< UNIT REMOVAL AND INSTALLATION >
TRANSMITTER
5. Install transmitter (1) to road wheel while pressing at position
(A).
CAUTION:
• Check that O-ring contacts horizontally with road wheel.
• Check that the base of the valve stem is positioned in the
groove of the metal plate.
6. Install and tighten the valve stem nut to the specified torque.
CAUTION:
Do not use power tool for installation.
7. Place wheel on turntable of tire machine. Ensure that transmitter
is 270 degrees from mounting/dismounting head.
NOTE:
Do not touch transmitter with mounting head.
8. Apply a suitable non-silicone lubricant to the tire outside bead.
CAUTION:
• Do not use silicone lubricant. Use of silicone lubricant will
deteriorate the tire and wheel.
• Do not allow lubricant to make contact with transmitter.
9. Install the tire outside bead onto the road wheel as normal.
NOTE:
If the tire is being reused, align the matching mark applied on
the tire with the position of the road wheel valve stem assembly for the purpose of road wheel and tire bal-
ance adjustment after installation. Ensure that the tire does not rotate relative to road wheel.
10. Install the valve core and inflate tire.
CAUTION:
Do not reuse valve core.
11. Install the valve cap.
CAUTION:
Do not reuse valve cap.
12. Balance the road wheel and tire assembly. Refer to
13. Install wheel and tire assembly in appropriate wheel position on vehicle. Refer to
.
NOTE:
If replacing the transmitter, then transmitter wake up operation must be performed. Refer to
.
14. Adjust neutral position of steering angle sensor. Refer to
BRC-6, "ADJUSTMENT OF STEERING ANGLE
SENSOR NEUTRAL POSITION : Special Repair Requirement"
.
JSEIA0377ZZ
Valve stem nut
tightening torque
: 7.7 N·m (0.79 kg-m, 68 in-lb)
WEIA0046E
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст