Nissan Maxima. Manual — part 1217
PREPARATION
WT-57
< PREPARATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000009466850
The actual shape of the tools may differ from those illustrated here.
Commercial Service Tools
INFOID:0000000009466851
Tool number
(TechMate No.)
Tool name
Description
—
(J-50190)
Signal Tech II
• Activate and display TPMS transmitter IDs
• Display tire pressure reported by the TPMS
transmitter
• Read TPMS DTCs
• Register TPMS transmitter IDs
• Test remote keyless entry keyfob relative
signal strength
• Check Intelligent Key relative signal
strength
• Confirm vehicle Intelligent Key antenna sig-
nal strength
• Compatible with future sensors
• Equipped with a display
KV48105501
(J-45295-A)
Transmitter activation tool
• Activate TPMS transmitter IDs
• Compatible with future sensors
• Equipped with a display (KV48105501 only)
ALEIA0131ZZ
ALEIA0183ZZ
Tool name
Description
Power tool
Loosening nuts, screws and bolts
PIIB1407E
WT-58
< PERIODIC MAINTENANCE >
ROAD WHEEL
PERIODIC MAINTENANCE
ROAD WHEEL
Inspection
INFOID:0000000009466852
ALUMINUM WHEEL
1. Check tires for wear and improper inflation.
2. Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel
runout.
a. Remove tire from aluminum wheel and mount on a tire balance machine. Refer to
to remove transmitter.
b. Set dial indicator as shown and rotate the wheel to check for
runout.
• Replace wheel if runout exceeds specification.
Wheel runout
Refer to
.
SFA975B
TIRE PRESSURE RECEIVER
WT-59
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
REMOVAL AND INSTALLATION
TIRE PRESSURE RECEIVER
Removal and Installation
INFOID:0000000009466853
REMOVAL
1. Remove instrument lower panel LH. Refer to
IP-11, "Removal and Installation"
2. Locate tire pressure receiver (1) to the right of the steering col-
umn and disconnect the harness connector from the tire pres-
sure receiver.
3. Remove tire pressure receiver (1) from bracket using a suitable
tool to release the bracket.
INSTALLATION
Installation is in the reverse order of removal.
AWEIA0123ZZ
WT-60
< REMOVAL AND INSTALLATION >
ROAD WHEEL TIRE ASSEMBLY
ROAD WHEEL TIRE ASSEMBLY
Adjustment
INFOID:0000000009466854
BALANCING WHEELS (ADHESIVE WEIGHT TYPE)
Preparation Before Adjustment
Remove inner and outer balance weights from the road wheel. Using releasing agent, remove double-faced
adhesive tape from the road wheel.
CAUTION:
• Be careful not to scratch the road wheel during removal.
• After removing double-faced adhesive tape, wipe clean all traces of releasing agent from the road
wheel.
Wheel Balance Adjustment
• If a balancer machine has an adhesive weight mode setting, select the adhesive weight mode setting and
skip Step 2. below. If a balancer machine only has the clip-on (rim flange) weight mode setting, follow Step 2.
to calculate the correct size adhesive weight.
1. Set road wheel on balancer machine using the center hole as a guide. Start the balancer machine.
2. For balancer machines that only have a clip-on (rim flange) weight mode setting, follow this step to calcu-
late the correct size adhesive weight to use. When inner and outer imbalance values are shown on the
balancer machine indicator, multiply outer imbalance value by 5/3 (1.67) to determine balance weight that
should be used. Select the outer balance weight with a value closest to the calculated value above and
install in to the designated outer position of, or at the designated angle in relation to the road wheel.
a. Indicated imbalance value
× 5/3 = balance weight to be installed
Calculation example:
23 g (0.81 oz)
× 5/3 (1.67) = 38.33 g (1.35 oz) ⇒ 40 g (1.41 oz)
balance weight (closer to calculated balance weight value)
NOTE:
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
37.4
⇒ 35 g (1.23 oz)
37.5
⇒ 40 g (1.41 oz)
3. Install balance weight in the position shown.
CAUTION:
• Do not install the inner balance weight before installing
the outer balance weight.
• Before installing the balance weight, be sure to clean the
mating surface of the road wheel.
• When installing balance weight (1) to road wheel, set it into the
grooved area (A) on the inner wall of the road wheel as shown
so that the balance weight center (B) is aligned with the bal-
ancer machine indication position (angle) (C).
CAUTION:
• Always use Genuine NISSAN adhesive balance weights.
• Balance weights are non-reusable; always replace with
new ones.
• Do not install more than three sheets of balance weight.
SMA054D
JPEIC0040ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст