Nissan Maxima. Manual — part 1178
TM-176
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
PADDLE SHIFTER
5. Remove the vehicle harness connector (C) and (D) from paddle
shifter.
6. Remove the paddle shifter bolts (E) and nuts (F).
7. Remove the paddle shifter from the steering column assembly.
INSTALLATION
Installation is in the reverse order of removal.
(A)
: Side of paddle shifter (shift-down)
(B)
: Side of paddle shifter (shift-up)
AWDIA0563ZZ
OIL PAN
TM-177
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
OIL PAN
Exploded View
INFOID:0000000010114019
Removal and Installation
INFOID:0000000009469206
REMOVAL
1. Drain CVT fluid from CVT. Refer to
.
2. Remove O-ring from drain plug.
3. Remove oil pan bolts (
).
•
: Front
4. Remove oil pan.
1.
Transaxle assembly
2.
Oil pan bolt
3.
Drain plug
4.
O-ring
5.
Oil pan
6.
Oil pan gasket
7.
Magnet
Apply CVT Fluid NS-2
JPDIA0608GB
SCIA8135J
TM-178
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
OIL PAN
5. Remove oil pan gasket (1) from oil pan (2).
6. Remove magnet (3) from oil pan.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Completely remove all moisture, oil and old gasket, etc. from the oil pan gasket mating surface of
transaxle case and oil pan.
• Do not reuse oil pan gasket, O-ring and oil pan bolts.
• Apply CVT fluid to O-ring.
• Install the oil pan assembly to the transaxle case with the following procedure.
- Install the oil pan assembly to the transaxle case, and then temporarily tighten the oil pan bolts.
CAUTION:
Do not reuse oil pan bolts.
- Tighten the oil pan bolts in a criss cross pattern to the specified torque.
- Tighten the oil pan bolts again clockwise to the specified torque.
Inspection
INFOID:0000000010114020
Check foreign materials in oil pan to help determine causes of malfunction. If the CVT fluid is very dark, smells
burned, or contains foreign particles, frictional material (clutches) may need replacement. A tacky film that will
not wipe clean indicates varnish build up. Varnish can cause valves and clutches to stick and can inhibit pump
pressure.
INSPECTION AFTER INSTALLATION
Check for CVT fluid leakage and check CVT fluid level. Refer to
SCIA8219J
CONTROL VALVE
TM-179
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL VALVE
Exploded View
INFOID:0000000010114021
Removal and Installation
INFOID:0000000009469209
REMOVAL
1. Disconnect battery negative terminal. Refer to
PG-67, "Removal and Installation (Battery)"
.
2. Remove the front fender protector side cover, Refer to
EXT-24, "Removal and Installation"
3. Disconnect the CVT unit harness connector. Refer to
TM-150, "Removal and Installation Procedure for
4. Remove the oil pan. Refer to
TM-177, "Removal and Installation"
5. Remove oil strainer.
1.
Transaxle assembly
2.
Control valve
3.
Snap ring
4.
Collar
5.
Manual plate
6.
Lock nut
7.
Lock nut
8.
Oil pan bolt
9.
O-ring
10. Drain plug
11. Oil pan
12. Oil pan gasket
13. Magnet
14. Lip seal
A.
O-ring
: NISSAN CVT Fluid NS-2
JPDIA0843GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст