Nissan Maxima. Manual — part 1177
TM-172
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
CVT SHIFT SELECTOR
4. Check that CVT shift selector stops at each position with the feel of engagement when it is moved through
all the positions. Check that the actual position of CVT shift selector matches the position shown by shift
position indicator and manual lever on the transaxle.
5. The method of operating CVT shift selector to individual posi-
tions correctly should be as shown.
• (A): Press shift selector handle button to operate CVT shift
selector, while depressing the brake pedal.
• (B): Press shift selector handle button to operate CVT shift
selector.
• (C): CVT shift selector can be operated without pressing shift
selector handle button.
6. When shift selector handle button is pressed in “P”, “R”, “N” or
“D” position without applying forward/backward force to CVT
shift selector, check shift selector handle button operation for
sticking.
7. Check that back-up lamps illuminate only when CVT shift selector is placed in the “R” position.
8. Check that back-up lamps do not illuminate when CVT shift selector is pushed toward the “R” position
when in the “P” or “N” position.
CAUTION:
Check the lighting without pressing shift selector handle button.
9. Check that the engine can only be started with CVT shift selector in the “P” and “N” positions.
10. Check that transaxle is locked completely when CVT shift selector is in “P” position.
11. Check the operation of manual mode.
1. When CVT shift selector is set to manual shift gate, make sure manual mode is displayed on combi-
nation meter.
2. Shift CVT shift selector to "+" and "-" sides, and make sure set shift position changes.
ADJUSTMENT
1. Set the park brake.
CAUTION:
Make sure the vehicle cannot move with parking brake set.
2. Loosen the control cable nut and place the manual lever in "P"
position.
3. Place the CVT shift selector in “P” position.
4. Push the control cable in with a load of 9.8 N (approximately 1
kg, 2.2 lb). Release the cable and temporarily tighten the control
cable nut.
NOTE:
Do not move the manual lever. Make sure the manual lever
stays in the "P" position.
5. Tighten the control cable nut. Refer to
.
CAUTION:
Secure manual lever when tightening nut.
6. Check the operation of the CVT.
ALDIA0216GB
SCIA2001E
CONTROL CABLE
TM-173
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
CONTROL CABLE
Exploded View
INFOID:0000000009469200
Removal and Installation
INFOID:0000000009469201
REMOVAL
CAUTION:
Make sure that parking brake is applied before removal/installation.
1. Remove front air duct. Refer to
EM-24, "Removal and Installation"
2. Remove air cleaner case assembly. Refer to
EM-24, "Removal and Installation"
3. Remove control cable nut (
).
4. Remove control cable (1) from manual lever (A).
5. Remove lock plate (2) from control cable.
6. Remove control cable from bracket (3).
7. Remove center console. Refer to
8. Remove control cable (1) from CVT shift selector assembly (2).
• (A): Ribbed surface
1.
CVT shift selector assembly
2.
Control cable
3.
Retainer grommet
4.
Lock plate
5.
Bracket
6.
Transaxle assembly
AWDIA1023ZZ
JPDIA0601ZZ
JPDIA0609ZZ
TM-174
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
CONTROL CABLE
9. Remove the bolts (A) from the support bracket (1) (if equipped).
10. Remove bracket covering the retainer grommet.
11. Remove the retainer grommet bolts (
) and the retainer grom-
met.
12. Remove the control cable (1) from the vehicle.
INSTALLATION
Installation is in the reverse order of removal.
• When installing control cable (1) to CVT shift selector assembly
(2), make sure that control cable is fully pressed in with the ribbed
surface (A) facing upward.
Inspection and Adjustment
INFOID:0000000009469202
ADJUSTMENT AFTER INSTALLATION
Adjust the CVT positions after installing control cable. Refer to
TM-171, "Inspection and Adjustment"
.
INSPECTION AFTER INSTALLATION
Check the CVT positions after adjusting the CVT positions. Refer to
TM-171, "Inspection and Adjustment"
ALCIA0087ZZ
(A)
: Dash trim
JPDIA0629ZZ
JPDIA0609ZZ
PADDLE SHIFTER
TM-175
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
PADDLE SHIFTER
Exploded View
INFOID:0000000009469203
Removal and Installation
INFOID:0000000009469204
REMOVAL
1. Park the vehicle on a level surface.
2. Remove the driver air bag module. Refer to
.
3. Remove the steering wheel. Refer to
ST-17, "Removal and Installation"
4. Remove the column cover. Refer to
IP-13, "Removal and Installation"
1.
Steering column assembly
2.
Paddle shifter (shift-down)
3.
Paddle shifter (shift-up)
AWDIA0557GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст