Nissan Maxima. Manual — part 1180
TM-184
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
SECONDARY SPEED SENSOR
SECONDARY SPEED SENSOR
Exploded View
INFOID:0000000010114023
Removal and Installation
INFOID:0000000009469212
REMOVAL
1. Disconnect the battery negative terminal. Refer to
PG-67, "Removal and Installation (Battery)"
2. Remove hoodledge cover (LH).
3. Remove engine room cover.
4. Remove front air duct. Refer to
EM-24, "Removal and Installation"
5. Remove air cleaner case assembly. Refer to
EM-24, "Removal and Installation"
6. Disconnect secondary speed sensor harness connector.
7. Remove secondary speed sensor (1) and shim (2).
CAUTION:
Do not lose the shim.
8. Remove O-ring (3) from secondary speed sensor.
CAUTION:
Do not reuse O-ring.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse O-ring.
• Apply CVT fluid to O-ring.
Inspection
INFOID:0000000010114024
Check for CVT fluid leakage and check CVT fluid level. Refer to
1.
Secondary speed sensor
2.
Shim
3.
Transaxle assembly
4.
O-ring
Apply CVT Fluid NS-2
JPDIA0687GB
JPDIA0617ZZ
DIFFERENTIAL SIDE OIL SEAL
TM-185
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
DIFFERENTIAL SIDE OIL SEAL
Exploded View
INFOID:0000000010114211
Removal and Installation
INFOID:0000000009469215
REMOVAL
1. Remove front fender protector side cover. Refer to
EXT-16, "Removal and Installation"
.
2. Remove front drive shafts. Refer to
FAX-9, "Removal and Installation (LH)"
(LH) and
(RH).
3. Remove differential side oil seals (1) using a suitable tool (A).
CAUTION:
Be careful not to scratch transaxle case and converter
housing.
INSTALLATION
Installation is in the reverse order of removal.
• Install each differential side oil seal evenly using Tool so that differ-
ential side oil seal protrudes by the dimension (C) respectively.
CAUTION:
• Do not reuse differential side oil seals.
1.
RH differential side oil seal
2.
LH differential side oil seal
3.
Transaxle assembly
Apply CVT Fluid NS-2
JPDIA0593ZZ
JPDIA0118ZZ
(A)
: Transaxle case side
(B)
: Converter housing side
Dimension (C)
: 0
± 0.5 mm (0 ± 0.020 in)
Tool number
: ST33400001 (J-26082)
JPDIA0618ZZ
TM-186
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
DIFFERENTIAL SIDE OIL SEAL
• Apply CVT fluid to differential side oil seals.
NOTE:
Differential side oil seal removal direction is used as the reference.
Inspection
INFOID:0000000010114212
Check for CVT fluid leakage and check CVT fluid level. Refer to
AIR BREATHER HOSE
TM-187
< REMOVAL AND INSTALLATION >
[CVT: RE0F09B]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
AIR BREATHER HOSE
Exploded View
INFOID:0000000010114213
Removal and Installation
INFOID:0000000009469218
REMOVAL
1. Remove front air duct. Refer to
EM-24, "Removal and Installation"
2. Remove air cleaner case assembly. Refer to
EM-24, "Removal and Installation"
3. Remove air breather hose from transaxle assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Install air breather hose with paint mark facing front.
• Insert air breather hose onto air breather tube until overlap area reaches the spool.
• Install air breather hose to heater pipe and air cleaner case assembly by fully inserting the clip.
• Make sure there are no pinched or restricted areas on air breather hose caused by bending or wind-
ing when installing it.
1.
Air cleaner case
2.
Air breather hose
3.
Transaxle assembly
4.
Heater pipe
5.
Clip
A.
Paint mark
Front
ALDIA0035ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст