Nissan Maxima. Manual — part 789
INT-26
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
2. Release the clip and pawl using a suitable tool, then remove rear kicking plate.
3. Partially remove front and rear body side welts.
4. Remove center pillar upper finisher cover and remove the screw.
5. Remove front seat belt adjuster cover and shoulder anchor bolt. Refer to
.
6. Release the clips and pawls using a suitable tool, then remove the center pillar lower finisher.
7. Release the clips using a suitable tool, then remove center pillar upper finisher.
Installation
Installation is in the reverse order of removal.
REAR SILL PLATE COVER
Removal
Release the pawls using a suitable tool, then remove the rear sill plate cover.
Installation
Installation is in the reverse order of removal.
REAR KICKING PLATE
Removal
Release the clip and pawl using a suitable tool, then remove rear kicking plate.
Installation
Installation is in the reverse order of removal.
REAR BODY SIDE WELT
Removal
1. Release the clip and pawl using a suitable tool, then remove rear kicking plate.
2. Release the clips and pawls using a suitable tool, then remove the center pillar lower finisher.
3. Remove rear body side welt from the body opening.
Installation
Installation is in the reverse order of removal.
REAR PARCEL SHELF FINISHER
INT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
REAR PARCEL SHELF FINISHER
Exploded View
INFOID:0000000009465887
With Sunshade
AWJIA0784ZZ
1.
Rear parcel shelf finisher
2. Cover
3.
Child anchor cover
4.
Rear parcel shelf finisher (under
side)
A. Dual lock fasteners
Clip
Front
INT-28
< REMOVAL AND INSTALLATION >
REAR PARCEL SHELF FINISHER
Without Sunshade
Removal and Installation
INFOID:0000000009465888
REMOVAL
1. Remove the halo upper frame assembly. Refer to
SE-70, "Removal and Installation"
(with fixed seatback,
WITH CLIMATE CONTROLLED SEATS),
SE-73, "Removal and Installation"
CLIMATE CONTROLLED SEATS),
SE-128, "Removal and Installation"
(with fixed seatback, W/O CLI-
MATE CONTROLLED SEATS)
SE-131, "Removal and Installation"
(with split seatback, W/O CLIMATE
CONTROLLED SEATS).
2. Remove high mounted stop lamp (if equipped). Refer to
EXL-164, "Removal and Installation"
3. Remove rear pillar finishers (RH/LH). Refer to
INT-24, "Removal and Installation"
4. Thread the rear seat belts (RH/LH/center) through vertical opening and release from rear parcel shelf fin-
isher.
5. Remove rear parcel shelf finisher using a suitable tool.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Make sure that clips are fully aligned with panel holes on body when installing, then press them in
completely.
AWJIA0786ZZ
1.
Rear parcel shelf finisher
2. Cover
3. Child anchor cover
4.
Rear parcel shelf finisher (under side)
Clip
Front
REAR SUNSHADE
INT-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
REAR SUNSHADE
Removal and Installation
INFOID:0000000009465889
REMOVAL
1. Remove the rear parcel shelf finisher. Refer to
INT-24, "Removal and Installation"
.
2. Remove the rear sunshade unit.
a. Remove the rear sunshade unit bolts.
b. Disconnect the rear sunshade unit harness connector and remove the rear sunshade unit.
INSTALLATION
Installation is in the reverse order of removal.
1.
Rear sunshade unit
Front
AWJIA0407ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст