Nissan Maxima. Manual — part 788
INT-22
< REMOVAL AND INSTALLATION >
REAR DOOR FINISHER
4. Remove the rear door finisher screws (A).
5. Release the rear door finisher clips using a suitable tool (A).
: Clip
6. Disconnect inside handle cable and the door lock cable from the back of rear door finisher.
7. Remove the rear door finisher.
INSTALLATION
Installation is in the reverse order of removal.
ALJIA0731ZZ
ALJIA0732ZZ
BODY SIDE TRIM
INT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BODY SIDE TRIM
Exploded View
INFOID:0000000009465885
1.
Front pillar finisher
2.
Dash side lower finisher
3.
Front kicking plate
4.
Front sill cover
5.
Center pillar lower finisher
6.
Rear sill cover
7.
Rear kicking plate
8.
Rear body side welt
9.
Rear pillar finisher
ALJIA0356ZZ
INT-24
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
Removal and Installation
INFOID:0000000009465886
CAUTION:
• Wrap the tip of a suitable tool with a cloth when removing metal clips from finishers.
• When removing or installing body side welts, do not allow butyl seal to come in contact with pillar
finishers.
FRONT PILLAR FINISHER
Removal
1. Remove front body side welt partially.
2. Disengage front pillar finisher (1) clip using a suitable tool (A).
3. Pull the front pillar finisher partially toward the vehicle.
4. Insert the a suitable tool (A) between the front pillar finisher bottom side and body side to disengage the
clip.
5. Pull front pillar finisher upwards and use a suitable tool to cut both clips.
6. Remove front pillar finisher (1).
Installation
Installation is in the reverse order of removal.
DASH SIDE LOWER FINISHER
Removal
1. Release the clip and pawls using a suitable tool, then remove front kicking plate.
2. Release the clips using a suitable tool, then remove dash side lower finisher.
Installation
Installation is in the reverse order of removal.
FRONT SILL PLATE COVER
Removal
Release the pawls using a suitable tool, then remove the front sill plate cover.
10. Screw cover
11. Center pillar upper finisher
12. Front seat belt adjuster cover
13. Front body side welt
A.
Screw
B.
Tether clip
Clip
Pawl
Metal clip
Front
: Clip
JMJIA0995ZZ
JMJIA2762ZZ
BODY SIDE TRIM
INT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Installation
Installation is in the reverse order of removal.
FRONT BODY SIDE WELT
Removal
1. Release the clip and pawls using a suitable tool, then remove front kicking plate.
2. Release the clips and pawls using a suitable tool, then remove the center pillar lower finisher.
3. Remove front body side welt from the body opening.
Installation
Installation is in the reverse order of removal.
FRONT KICKING PLATE INNER
Removal
1. Disengage the pawls with a suitable tool (A) from the body.
2. Remove front kicking plate inner (1).
Installation
Installation is in the reverse order of removal.
FRONT KICKING PLATE OUTER
Removal
1. Disengage the pawls from the body with a suitable tool (A).
2. Remove front kicking plate outer (1)
Installation
Installation is in the reverse order of removal.
REAR PILLAR FINISHER
Removal
1. Partially remove rear body side welt.
2. Remove screw cover, then remove the screw.
3. Release the clips using a suitable tool, then remove rear pillar finisher.
Installation
Installation is in the reverse order of removal.
CENTER PILLAR UPPER FINISHER
Removal
1. Release the clip and pawls using a suitable tool, then remove front kicking plate.
: Pawl
JMJIA0996ZZ
: Pawl
JMJIA0999ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст