Nissan Maxima. Manual — part 533
EM-20
< PERIODIC MAINTENANCE >
CAMSHAFT VALVE CLEARANCE
9. Check only those valve lifters as shown.
10. Turn the crankshaft 240
°.
11. Set No.5 cylinder at TDC on its compression stroke.
12. Check only those valve lifters as shown.
13. If all valve lifter clearances are within specification, install the following components. If the valve lifter
clearances are out of specification, adjust the valve lifter clearances.
• Intake manifold collectors
• Rocker covers
• All spark plugs
• All ignition coils
VALVE LIFTER ADJUSTING
Crank Position
Valve No. 2
Valve No. 3
Valve No. 4
Valve No. 5
No. 3 TDC
Intake
Intake
Exhaust
Exhaust
SEM894E
Crank Position
Valve No. 1
Valve No. 4
Valve No. 5
Valve No. 6
No. 5 TDC
Exhaust
Intake
Intake
Exhaust
SEM958E
CAMSHAFT VALVE CLEARANCE
EM-21
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
CAUTION:
Adjust valve lifter clearance while engine is cold.
NOTE:
• Perform adjustment by selecting the correct head thickness of the valve lifter (adjusting shims are not used).
• The specified valve lifter thickness is the dimension at normal temperatures. Ignore dimensional differences
caused by temperature. Use specifications for hot engine condition to confirm valve lifter clearances.
1. Remove the camshaft. Refer to
EM-76, "Removal and Installation"
.
2. Remove the valve lifter that was measured as being outside the standard specifications.
3. Measure the center thickness of the removed valve lifter using
suitable tool as shown.
4. Use the equation below to calculate the replacement valve lifter
thickness.
Valve lifter thickness calculation equation: t = t1 + (C1 - C2)
t = thickness of the replacement valve lifter
t1 = thickness of the removed valve lifter
C1 = measured valve lifter clearance
C2 = standard valve lifter clearance
• The thickness of the new valve lifter can be identified by the
stamp mark on the reverse side (inside the valve lifter).
• Available thickness of the valve lifter (factory setting):
7.88 - 8.40 mm (0.3102 - 0.3307 in), in 0.02 mm (0.0008 in)
increments, in 27 sizes (intake/exhaust). Refer to
5. Install the selected replacement valve lifter.
6. Install the camshaft. Refer to
EM-76, "Removal and Installation"
7. Rotate the crankshaft a few turns by hand.
8. Confirm that the valve lifter clearances are within specification.
9. After the engine has been run to full operating temperature, confirm that the valve lifter clearances are
within specification.
* Approximately 80
°C (176°F)
SEM754G
SEM755G
Standard Valve Clearance
Cold
Hot* (reference data)
Intake
0.26 - 0.34 mm (0.010 - 0.013 in)
0.304 - 0.416 mm (0.012 - 0.016 in)
Exhaust
0.29 - 0.37 mm (0.011 - 0.015 in)
0.308 - 0.432 mm (0.012 - 0.017 in)
EM-22
< PERIODIC MAINTENANCE >
COMPRESSION PRESSURE
COMPRESSION PRESSURE
On-Vehicle Service
INFOID:0000000009466010
CHECKING COMPRESSION PRESSURE
1. Run the engine until it reaches normal operating temperature.
2. Turn the ignition switch to OFF.
3. Release fuel pressure. Refer to
.
4. Remove all six spark plugs.
EM-12, "Removal and Installation"
5. Attach a compression tester to No. 1 cylinder.
6. Depress accelerator pedal fully to keep the electric throttle control actuator butterfly-valve wide open to
maximize air intake flow.
7. Crank the engine and record the highest gauge indication.
8. Repeat the measurement on each cylinder (steps 5 - 7).
Unit: kPa (kg/cm
2
, psi)/rpm
• Always use a fully-charged battery to obtain specified engine speed.
• If the engine speed is out of the specified range check the battery and recharge as necessary. Check
the engine speed again with the battery properly charged.
• If some cylinders have low compression pressure, pour a small amount of engine oil into the spark plug
hole of the cylinder to re-check it for compression.
- If the added engine oil improves the compression, piston rings may be worn out or damaged. Check the
piston rings and replace if necessary
- If the compression pressure remains at low level despite the addition of engine oil, the valves may be
malfunctioning. Check the valves for damage. Replace the valve or valve seat accordingly.
• If two adjacent cylinders have respectively low compression pressure and their compression remains
low even after the addition of engine oil, cylinder head gaskets may be leaking, or a valve in adjacent
cylinders may be damaged. Inspect and repair as required.
• If the compression pressure is below the minimum value, check the valve clearances and parts associ-
ated with the combustion chamber (valve, valve seat, piston, piston ring, cylinder bore, cylinder head,
cylinder head gasket). After the checking, measure the compression pressure again.
SBIA0533E
Standard
Minimum
Difference limit between cylinders
1,275 (13.0, 185)/300
981 (10.0, 142)/300
98 (1.0, 14)/300
ENGINE ROOM COVER
EM-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
REMOVAL AND INSTALLATION
ENGINE ROOM COVER
Removal and Installation
INFOID:0000000009466011
CAUTION:
Do not damage or scratch engine room cover when installing or removing.
REMOVAL
• Remove the engine room cover bolts and engine room cover.
INSTALLATION
Installation is in the reverse order of removal.
AWBIA0718ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст