Nissan Maxima. Manual — part 534
EM-24
< REMOVAL AND INSTALLATION >
AIR CLEANER AND AIR DUCT
AIR CLEANER AND AIR DUCT
Removal and Installation
INFOID:0000000009466012
REMOVAL
1. Remove engine room cover. Refer to
EM-23, "Removal and Installation"
2. Remove front air duct.
3. Disconnect the tube clamp at the electric throttle control actuator and at the air duct hose and resonator
assembly.
4. Disconnect the blow-by hose.
5. Remove air duct hose and resonator assembly.
6. Disconnect mass air flow sensor.
7. Remove mass air flow sensor from air cleaner case (upper), as necessary.
CAUTION:
Handle mass air flow sensor with care.
• Do not shock it.
• Do not disassemble it.
• Do not touch its sensor.
8. Disconnect transaxle breather.
9. Remove air cleaner case assembly.
INSTALLATION
Installation is in the reverse order of removal.
1.
Air duct hose and resonator assembly 2. Front air duct
3.
Air cleaner case (lower)
4.
Grommets
5.
Air cleaner case mounting bracket 6.
Bracket
7.
Air cleaner filter
8.
Air cleaner case (upper)
9.
Mass air flow sensor
A.
To electric throttle control actuator
B. Air cleaner case side clips
AWBIA0849ZZ
INTAKE MANIFOLD COLLECTOR
EM-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
INTAKE MANIFOLD COLLECTOR
Removal and Installation
INFOID:0000000009466013
WARNING:
To avoid the danger of being scalded, do not drain the coolant when the engine is hot.
CAUTION:
Do not remove power valves.
NOTE:
When removing components such as hoses, tubes/lines, etc., cap or plug openings to prevent fluid from spill-
ing.
REMOVAL
1. Remove the cowl top, lower cowl top extension and lower cowl top extension brace. Refer to
2. Remove the engine room cover. Refer to
EM-23, "Removal and Installation"
3. Remove front air duct and air duct hose and resonator assembly. Refer to
1. Intake manifold collector
2. Intake manifold collector gasket
3.
Electric throttle control actuator gasket
4. Electric throttle control actuator A. Refer to INSTALLATION
B. Refer to INSTALLATION
AWBIA1336ZZ
EM-26
< REMOVAL AND INSTALLATION >
INTAKE MANIFOLD COLLECTOR
4. Remove the electric throttle control actuator bolts in the reverse
order as shown and remove the electric throttle control actuator
and position aside.
CAUTION:
• Handle carefully to avoid any shock to the electric throttle
control actuator.
• Do not disassemble.
5. Disconnect the following:
• Power brake booster vacuum hose
• PCV hose
• Electric throttle control actuator electrical connector
• EVAP canister purge hose
CAUTION:
Cover any engine openings to avoid the entry of any foreign material.
6. Remove the EVAP canister purge volume solenoid valve bracket bolt. Position the valve aside.
7. Loosen the intake manifold collector bolts in the order as shown
using power tool, and remove the intake manifold collector and
gasket.
8. If necessary remove the following components:
• VIAS control solenoid valve
• EVAP canister purge volume control solenoid valve
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Do not reuse intake manifold collector gasket or electric throttle control actuator gasket.
• Tighten intake manifold collector bolts in the order as shown.
SEM711G
ALBIA0228ZZ
ALBIA0240ZZ
INTAKE MANIFOLD COLLECTOR
EM-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
A
EM
N
P
O
• Tighten electric throttle control actuator bolts in the order shown.
NOTE:
After installation, it is necessary to re-calibrate the electric throttle control actuator as follows:
1. Perform the
″Throttle Valve Closed Position Learning″ when harness connector of the electric throttle con-
trol actuator is disconnected. Refer to
EC-21, "THROTTLE VALVE CLOSED POSITION LEARNING :
2. Perform the
″Idle Air Volume Learning″ when the electric throttle control actuator is replaced. Refer to
21, "IDLE AIR VOLUME LEARNING : Special Repair Requirement"
.
SEM711G
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст