Nissan Maxima. Manual — part 1026
FRONT SEAT
SE-77
< UNIT DISASSEMBLY AND ASSEMBLY >
[WITH CLIMATE CONTROLLED SEATS]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
DRIVER SIDE : Disassembly and Assembly
INFOID:0000000009468152
SEAT ASSEMBLY WITH SIDE AIR BAG MODULE
WARNING:
Do not leave any objects (screwdriver, tools, etc.) on the seat during seatback repair. It can lead to per-
sonal injury if the side air bag should accidentally deploy.
CAUTION:
• Before servicing, turn the ignition switch OFF, disconnect both battery terminals and wait at least
three minutes.
• Handle the side air bag module carefully. During disassembly, always hold the side air bag module,
do not let it hang by the wire harness.
• Always place side air bag module with the stud bolt side facing downward.
• Always work from the side or back of the seatback assembly, do not work in front of the seat.
• Do not use air tools or electric tools when servicing the seat assembly.
• Replace the side air bag module if it has been dropped or sustained an impact.
• Do not insert any objects into the side air bag module.
• Do not disassemble the side air bag module.
• Do not expose the side air bag module to temperatures exceeding 93
°C (200°F).
• Do not expose the side air bag module to any oil, grease or water.
• During disassembly, do not damage the trim cover, chutes, connectors, retainers, clips, module har-
ness or the side air bag module.
NOTE:
• If the vehicle has been involved in a collision and the side air bag has deployed, the front seatback assembly
must be replaced.
• For side air bag module removal and installation, refer to
SR-21, "Removal and Installation"
Disassembly
1. Remove the front seat assembly. Refer to
SE-68, "Removal and Installation"
.
2. Remove the seatback board as follows:
NOTE:
The seatback board is attached to the seat frame with the follow-
ing:
• Two top hooks (A)
• Two side hooks (B)
• Two bottom retainers (C)
10. Seat cushion trim
11. Seat cushion pad
12. Thigh extension tether
13. Thigh extension assembly
14. Climate controlled seat control unit 15. Seat cushion front finisher
16. Front slide cover
17. Clip
18. Power seat control unit
19. Seat cushion thermal electric device
(TED)
20. Lower seat duct
21. Climate controlled seat blower fil-
ter
22. Climate controlled seat blower motor
assembly
23. Seat frame assembly
24. Rear slide cover
25. Power seat switch
26. Seat slide and lifter switch knob
27. Seat recline knob
28. Lumbar support switch
29. Seat cushion outer finisher (LH)
30. Recline device outer cover
31. Seat cushion inner finisher inside
(LH)
32. Seatback assembly
33. Side air bag module
34. Seatback thermal electric device
(TED)
35. Upper seat duct
36. Headrest holder (locked)
37. Headrest holder (free)
38. Seatback frame
39. Seatback trim
40. Seatback pad
41. Headrest
42. Chute rod
ALJIA0587ZZ
SE-78
< UNIT DISASSEMBLY AND ASSEMBLY >
[WITH CLIMATE CONTROLLED SEATS]
FRONT SEAT
a. From the bottom of the seat, unhook the two seat skirt hooks as
shown.
b. Carefully pull upward on the lower seatback board to release the
two bottom retainers (C).
CAUTION:
Do not pull outward at two top hooks (A)
c.
Hold the seatback board at the side hook locations (B) and push
in the side hooks to release them from the seatback frame, then
pull it rearward.
d. Carefully pull the seatback board downward to disengage the
top hooks as shown.
CAUTION:
Use care not to break the seatback board hooks and retain-
ers. Replace seatback board if any hooks or retainers are
damaged.
3. Disconnect the upper seat duct.
4. Remove and discard the two chute rod bolts (A), then remove
the chute rod (1).
CAUTION:
Do not reuse the chute rod bolts.
ALJIA0588ZZ
ALJIA0587ZZ
ALJIA0589ZZ
Chute rod bolts (A)
: 8.2 N·m (0.84 kg-m, 73 in-lb)
ALJIA0590ZZ
FRONT SEAT
SE-79
< UNIT DISASSEMBLY AND ASSEMBLY >
[WITH CLIMATE CONTROLLED SEATS]
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
5. Release the seven seatback retainers from the seatback frame
as shown.
6. Reach in from the bottom of the seatback to release the guide
clips on the headrest holder. Squeeze the clips at the bottom
and push upward to remove as shown.
7. Push the seatback trim and seatback pad forward at the bottom
(1), then holding the seatback assembly on both sides, lift
upward (2). Remove the seatback trim and seatback pad as an
assembly from the seatback frame.
ALJIA0598ZZ
PIIB4084J
ALJIA0599ZZ
SE-80
< UNIT DISASSEMBLY AND ASSEMBLY >
[WITH CLIMATE CONTROLLED SEATS]
FRONT SEAT
8. If required, separate the seatback trim from the seatback pad as
follows:
NOTE:
The seatback trim is attached to the seatback pad with the fol-
lowing:
• Five top hog rings (A)
• Four side hog rings (B)
• Three middle hog rings (C)
• Three bottom velcro fasteners (D)
a. Pull the seatback trim from the seatback pad to detach the vel-
cro fasteners.
b. Position the seatback trim to access the middle hog rings.
Remove the middle and side hog rings.
c.
Remove the top hog rings, then separate the seatback trim from
the seatback pad.
Assembly
Assembly is in the reverse order of disassembly. During assembly, note the following.
• When installing the seatback trim, firmly push down while sliding
your hand along the seams as shown (arrow) to ensure the velcro
fasteners are fastened properly.
• Make sure the chute rod is properly positioned and installed as shown.
: Front
ALJIA0594ZZ
ALJIA0656ZZ
ALJIA0654ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст