Qashqai J11. Meter warning lamp & indicator — part 5
MWI-66
< DTC/CIRCUIT DIAGNOSIS >
POWER SUPPLY AND GROUND CIRCUIT
POWER SUPPLY AND GROUND CIRCUIT
COMBINATION METER
COMBINATION METER : Diagnosis Procedure
INFOID:0000000010329985
1.
CHECK FUSE
Check for blown fuses.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Be sure to eliminate cause of malfunction before installing new fuse.
2.
CHECK POWER SUPPLY CIRCUIT
Check voltage between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Check harness between combination meter and fuse.
3.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector.
3.
Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
Terminal No.
Signal name
Fuses No.
45
Battery power supply
21
46
Ignition signal
3
Terminals
Ignition switch position
(+)
(
−
)
Combination meter
OFF
ON
Connector
Terminal
M52
45
Ground
Battery voltage
Battery voltage
46
Approx. 0 V
Battery voltage
Combination meter
Ground
Continuity
Connector
Terminal
M52
1 - 52
Existed
MWI
PARKING BRAKE SWITCH SIGNAL CIRCUIT
MWI-67
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
PARKING BRAKE SWITCH SIGNAL CIRCUIT
Diagnosis Procedure
INFOID:0000000010435893
Regarding Wiring Diagram information, refer to EHS-PKB
1.
With CONSULT perform the self diagnosis of ELECTRIC PARKING BRAKE CONTROL UNIT. Refer to
2.
Check the DTC of the parking brake switch. Refer to
MWI-68
< DTC/CIRCUIT DIAGNOSIS >
FUEL LEVEL SENSOR SIGNAL CIRCUIT
FUEL LEVEL SENSOR SIGNAL CIRCUIT
Component Function Check
INFOID:0000000010329986
1.
PERFORM COMPONENT FUNCTION CHECK (1)
1.
Turn ignition switch OFF.
2.
Disconnect fuel level sensor unit and fuel pump (fuel level sensor) connector.
3.
Connect variable resistor between harness connector terminals located on the vehicle side of the fuel
level sensor unit and fuel pump (fuel level sensor).
*1: with gasoline engine
*2: with diesel engine
4.
Set variable resistor according to the resistance value shown in the following table and turn ignition switch
ON.
*: Reference resistance values used when the combination meter judges the indication position of the fuel
gauge.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
.
2.
PERFORM COMPONENT FUNCTION CHECK (2)
Check the fuel level sensor unit and fuel pump (fuel level sensor) and/or fuel level sensor unit (sub). Refer to
MWI-70, "Component Inspection"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace the fuel level sensor unit and fuel pump (fuel level sensor) and/or fuel level sensor unit
(sub). Refer to
FL-7, "Removal and Installation"
(HRA2DDT models),
(MR20DD models),
FL-48, "Removal and Installation"
(K9K models),
(2WD with R9M models),
FL-19, "Removal and Installation"
(MR16DDT) or
FL-65, "4WD : Removal and Installation"
(4WD with R9M models).
Diagnosis Procedure
INFOID:0000000010329987
FOR DIESEL ENGINE MODELS
1.
CHECK FUEL PUMP CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector and fuel pump control module connector.
Fuel level sensor unit and fuel pump (fuel level sensor)
Connector
Terminals
B72
*1
2
5
B94
*2
5
6
Resistance (
Ω
)
*
(Approx.)
Fuel gauge indication position
(Approx.)
93
Full
140
3/4
186
1/2
232
1/4
255
1/8
243,5
TURN OFF
255
TURN ON
280.0
Empty
MWI
FUEL LEVEL SENSOR SIGNAL CIRCUIT
MWI-69
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
3.
Check continuity between combination meter harness connector and fuel pump control module harness
connector.
4.
Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK FUEL PUMP CONTROL NMODULE GROUND CIRCUIT
Check continuity between fuel pump control module harness connector and combination meter harness con-
nector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair harness or connector.
3.
CHECK FUEL LEVEL SENSOR UNIT AND FUEL PUMP (FUEL LEVEL SENSOR) CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect fuel level sensor unit and fuel pump (fuel level sensor) connector and fuel pump controle
module connector.
3.
Check continuity between fuel level sensor unit and fuel pump (fuel level sensor) harness connector and
fuel pump control module harness connector.
4.
Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair harness or connector.
4.
CHECK FUEL LEVEL SENSOR UNIT AND FUEL PUMP (FUEL LEVEL SENSOR) GROUND CIRCUIT
Check continuity between fuel level sensor unit and fuel pump (fuel level sensor) connector connector and fuel
pump control module harness connector.
Combination meter
Fuel pump controle module
Continuity
Connector
Terminal
Connector
Terminal
M52
51
B77
11
Existed
Combination meter
Ground
Continuity
Connector
Terminal
M52
51
Not existed
Fuel pump control module
Combination meter
Continuity
Connector
Terminal
Connector
Terminal
B77
12
M52
44
Existed
Fuel level sensor unit and fuel
pump (fuel level sensor)
Fuel pump control module
Continuity
Connector
Terminal
Connector
Terminal
B94
5
B77
2
Existed
Fuel level sensor unit and fuel
pump (fuel level sensor)t
Ground
Continuity
Connector
Terminal
B94
5
Not existed
MWI-70
< DTC/CIRCUIT DIAGNOSIS >
FUEL LEVEL SENSOR SIGNAL CIRCUIT
Is the inspection result normal?
YES
>> Replace the fuel level sensor unit and fuel pump (fuel level sensor). Refer to
FL-48, "Removal and Installation"
(K9K engine models) or
(2WD with R9M engine models),
FL-19, "Removal and Installation"
(MR16DDT) or
FL-65, "4WD : Removal and Installation"
(4WD with R9M engine models)
NO
>> Repair harness or connector.
FOR GASOLINE ENGINE MODELS
1.
CHECK FUEL LEVEL SENSOR UNIT AND FUEL PUMP (FUEL LEVEL SENSOR) CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector and fuel level sensor unit and fuel pump (fuel level sensor) con-
nector.
3.
Check continuity between combination meter harness connector and fuel level sensor unit and fuel pump
(fuel level sensor) harness connector.
4.
Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK FUEL LEVEL SENSOR UNIT AND FUEL PUMP (FUEL LEVEL SENSOR) GROUND CIRCUIT
Check continuity between fuel level sensor unit and fuel pump (fuel level sensor) harness connector and com-
bination meter harness connector.
Is the inspection result normal?
YES
>> Replace fuel level sensor unit and fuel pump (fuel level sensor). Refer to
NO
>> Repair harness or connector.
Component Inspection
INFOID:0000000010329988
2WD MODELS
1.
CHECK FUEL LEVEL SENSOR UNIT AND FUEL PUMP (FUEL LEVEL SENSOR)
1.
Remove the fuel level sensor unit and fuel pump (fuel level sensor).
-
Refer to
(HRA2DDT engine models)
Fuel pump controle module
Fuel level sensor unit and fuel
pump (fuel level sensor)
Continuity
Connector
Terminal
Connector
Terminal
B77
1
B94
6
Existed
Combination meter
Fuel level sensor unit and fuel
pump (fuel level sensor)
Continuity
Connector
Terminal
Connector
Terminal
M52
51
B72
2
Existed
Combination meter
Ground
Continuity
Connector
Terminal
M52
51
Not existed
Fuel level sensor unit and fuel
pump (fuel level sensor)
Combination meter
Continuity
Connector
Terminal
Connector
Terminal
B72
5
M52
44
Existed
MWI
FUEL LEVEL SENSOR SIGNAL CIRCUIT
MWI-71
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
-
Refer to
(K9K engine models)
-
-
Refer to
(MR20DD engine models)
-
Refer to
(MR16DDT engine models)
2.
Check the resistance between fuel level sensor unit and fuel pump (fuel level sensor).
*: When float rod is contact with stopper.
Is inspection result OK?
YES
>> INSPECTION END
NO
>> Replace fuel level sensor unit and fuel pump (fuel level sensor). Refer to
FL-48, "Removal and Installation"
(K9K engine mod-
els) or
FL-61, "2WD : Removal and Installation"
(MR16DDT engine models) or
FL-32, "Removal and Installation"
models).
4WD MODELS
1.
CHECK FUEL LEVEL SENSOR UNIT AND FUEL PUMP (FUEL LEVEL SENSOR)
1.
Remove the fuel level sensor unit and fuel pump (fuel level sensor). Refer to
2.
Check the resistance between fuel level sensor unit and fuel pump (fuel level sensor).
*: When float rod is contact with stopper.
Is inspection result OK?
YES
>> INSPECTION END.
NO
>> Replace fuel level sensor unit and fuel pump (fuel level sensor). Refer to
.
Fuel level sensor unit and fuel pump
(fuel level sensor) connector
Terminals
Condition
Resistance (
Ω
)
(Approx.)
Height [mm (in)]
B72 (HRA2DDT engine models)
2
5
Full
*
5
178.4 (7.02)
Empty
*
81.5
36.2 (1.425)
B94 (R9M and K9K engine models)
5
6
Full
*
5
178.4 (7.02)
Empty
*
81.5
36.2 (1.425)
Terminals
Condition
Resistance (
Ω
)
(Approx.)
Height [mm (in)]
Fuel level sensor unit
and fuel pump (fuel
level sensor)
5
6
Full
*
93
186.3 (7.33)
Empty
*
280
36.3 (1.429)
MWI-72
< DTC/CIRCUIT DIAGNOSIS >
OIL LEVEL SENSOR SIGNAL CIRCUIT
OIL LEVEL SENSOR SIGNAL CIRCUIT
Component Function Check
INFOID:0000000010329989
1.
CHECK COMBINATION METER INPUT SIGNAL
Select the “Data Monitor” for the “METER/M&A” and check the “OIL W/L” monitor value.
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000010329990
1.
CHECK OIL LEVEL SENSOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector and oil level sensor connector.
3.
Check continuity between combination meter connector and oil level sensor harness connector.
*1: K9K engine models
*2: R9M engine models
*3: MR16DDT engine models
4.
Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
Component Inspection
INFOID:0000000010329991
1.
CHECK OIL LEVEL SENSOR
Check continuity between oil level sensor and ground.
Is the inspection result normal?
“OIL W/L”
Ignition switch ON
: On
Engine running
: Off
Terminals
Continuity
(+)
(
−
)
Combination meter
Oil level sensor
Connector
Terminal
Connector
Terminal
M52
49
F141
*1
F142
*2
F216
*3
1
Existed
Terminals
Continuity
(+)
(
−
)
Combination meter
Ground
Connector
Terminal
M52
49
Not existed
Condition
Continuity
Engine stopped
Existed
Engine running
Not existed
MWI
OIL LEVEL SENSOR SIGNAL CIRCUIT
MWI-73
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
YES
>> INSPECTION END
NO
>> Replace oil level sensor.
MWI-74
< DTC/CIRCUIT DIAGNOSIS >
AMBIENT SENSOR SIGNAL CIRCUIT
AMBIENT SENSOR SIGNAL CIRCUIT
Diagnosis Procedure
INFOID:0000000010329992
1.
CHECK AMBIENT SENSOR CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector and ouotside temperature sender connector.
3.
Check continuity between combination meter harness connector and ambient sensor harness connector.
4.
Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK AMBIENT SENSOR GROUND CIRCUIT
Check continuity between combination meter harness connector and ambient sensor harness connector.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair harness or connector.
Component Inspection
INFOID:0000000010329993
HAC-130, "Removal and Installation"
Terminals
Continuity
(+)
(
−
)
Combination meter
Ambient sensor
Connector
Terminal
Connector
Terminal
M51
15
E12
1
Existed
Terminals
Continuity
(+)
(
−
)
Combination meter
Ground
Connector
Terminal
M51
1
Not existed
Terminals
Continuity
(+)
(
−
)
Combination meter
Ambient sensor sender
Connector
Terminal
Connector
Terminal
M51
20
E12
2
Existed
MWI
METER CONTROL SWITCH SIGNAL CIRCUIT
MWI-75
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
METER CONTROL SWITCH SIGNAL CIRCUIT
Diagnosis Procedure
INFOID:0000000010435886
Regarding Wiring Diagram information, refer to
.
1.
CHECK METER CONTROL SWITCH SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between the following terminals of the meter control switch harness connector M53.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> GO TO 2.
2.
CHECK METER CONTROL SWITCH HARNESS
1.
Turn ignition switch OFF.
2.
Disconnect combination meter harness connector M51 and meter control switch harness connector M53.
3.
Check continuity between combination meter harness connector M51 and meter control switch harness
connector M53.
4.
Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connectors.
Meter control switch
Condition
Voltage
(Approx.)
Connector
Terminals
(+)
(
−
)
M53
7
4
When illumination control switch (
−
) is pressed
0 V
Other than the above
5 V
5
When trip reset switch is pressed
0 V
Other than the above
5 V
6
When illumination control switch (+) is pressed
0 V
Other than the above
5 V
Combination meter
Meter control switch
Continuity
Connector
Terminal
Connector
Terminal
M51
18
M53
5
Yes
37
7
36
6
17
4
Combination meter
Ground
Continuity
Connector
Terminal
M51
18
No
37
36
17
MWI-76
< DTC/CIRCUIT DIAGNOSIS >
METER CONTROL SWITCH SIGNAL CIRCUIT
Component Inspection
INFOID:0000000010435887
1.
CHECK METER CONTROL SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect meter control switch connector.
3.
Check meter control switch.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace meter control switch. Refer to
MWI-87, "Removal and Installation"
.
Meter control switch
Condition
Continuity
Terminals
7
4
When illumination control switch (
−
) is pressed
Yes
Other than the above
No
5
When trip reset switch is pressed
Yes
Other than the above
No
6
When illumination control switch (+) is pressed
Yes
Other than the above
No
MWI
STEERING SWITCH
MWI-77
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
STEERING SWITCH
Description
INFOID:0000000010435888
When one of the steering switches is pushed, the resistance in the steering switch changes the signal to
identify which button is controlling the information display.
Diagnosis Procedure
INFOID:0000000010435889
Regarding Wiring Diagram information, refer to
.
1.
CHECK STEERING SWITCH CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter harness connector M51 and spiral cable harness connector M303.
3.
Check continuity between combination meter harness connector M51 and spiral cable harness connector
M303.
4.
Check continuity between combination meter harness connector M51 and ground.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Repair or replace harness or connector.
Component Inspection
INFOID:0000000010435890
1.
CHECK STEERING SWITCH RESISTANCE
Check resistance between the following steering switch terminals.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace steering wheel switch. Refer to
Combination meter
Spiral cable
Continuity
Connector
Terminal
Connector
Terminal
M51
21
M303
4
Yes
22
5
23
10
Combination meter
Ground
Continuity
Connector
Terminal
M51
21
No
22
23
Terminal
Signal name
Condition
Resistance (
Ω
)
(Approx.)
10
4
Display
Depress DISP switch.
2023
Back
Depress
switch.
723
5
Enter
Depress ENTER switch.
2023
Menu Up
Depress
switch.
121
Menu Down
Depress
switch.
321
MWI-78
< DTC/CIRCUIT DIAGNOSIS >
STEERING SWITCH
2.
CHECK SPIRAL CABLE
Check continuity between the following spiral cable terminals.
Is the inspection result normal?
YES
>> Inspection End.
NO
>> Replace spiral cable. Refer to
SR-17, "Removal and Installation"
Terminals
Continuity
24
10
Yes
29
5
23
4
MWI
THE FUEL GAUGE DOES NOT MOVE
MWI-79
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
SYMPTOM DIAGNOSIS
THE FUEL GAUGE DOES NOT MOVE
Description
INFOID:0000000010329995
Fuel gauge does not move from a certain position.
Diagnosis Procedure
INFOID:0000000010329996
1.
CONDUCTING THE COMBINATION METER SELF-DIAGNOSIS MODE
Perform the self-diagnosis mode of combination meter, and then check that the fuel gauge operates normally.
Refer to
MWI-30, "CONSULT Function (METER/M&A)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace combination meter. Refer to
MWI-86, "Removal and Installation"
2.
CHECK FLOAT INTERFERENCE
Check that the float arm interferes with or binds to other components in the fuel tank.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning part.
3.
CHECK FUEL LEVEL SENSOR SIGNAL CIRCUIT
Check the fuel level sensor signal circuit. Refer to
MWI-68, "Component Function Check"
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-44, "Intermittent Incident"
.
NO
>> Repair or replace malfunctioning parts.
MWI-80
< REMOVAL AND INSTALLATION >
COMBINATION METER
REMOVAL AND INSTALLATION
COMBINATION METER
Removal and Installation
INFOID:0000000010330004
REMOVAL
1.
Disconnect the negative battery terminal. refer to
2.
Remove the cluster lid A. Refer to
.
3.
Remove screws (A), from the combination meter (1).
4.
Release the clips and remove the combination meter (1) from
the instrument panel.
: Clips
5.
Disconnect the harness connectors from the combination meter
and remove.
INSTALLATION
Installation is in the reverse order of removal.
ALNIA1607ZZ
ALNIA1608ZZ
MWI
THE AMBIENT TEMPERATURE DISPLAY IS INCORRECT
MWI-81
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE AMBIENT TEMPERATURE DISPLAY IS INCORRECT
Description
INFOID:0000000010330001
• The ambient air temperature display flashes and the ambient air temperature is not displayed.
• The displayed air ambient temperature is higher than the actual temperature.
• The displayed air ambient temperature is lower than the actual temperature.
Diagnosis Procedure
INFOID:0000000010330002
1.
CHECK AMBIENT SENSOR SIGNAL CIRCUIT
Check the ambient sensor signal circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair harness or connector.
2.
CHECK AMBIENT SENSOR
Perform a unit check for the ambient sensor. Refer to
MWI-74, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter.
NO
>> Replace ambient sensor. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст