Qashqai J11. Meter warning lamp & indicator — part 6
MWI-82
< UNIT DISASSEMBLY AND ASSEMBLY >
COMBINATION METER
UNIT DISASSEMBLY AND ASSEMBLY
COMBINATION METER
Exploded View
INFOID:0000000010330006
Disassembly and Assembly
INFOID:0000000010330007
CAUTION:
• Do not touch the display, pointer, inside of combination meter or the printed area of the dial during
disassembly or assembly.
• Keep away from magnetic sources.
• Do not damage the combination meter lens.
DISASSEMBLY
1.
Remove the combination meter. Refer to
MWI-80, "Removal and Installation"
2.
Release pawls and remove the combination meter lens.
ASSEMBLY
Assembly is in the reverse order of disassembly.
1.
Combination meter
2.
Combination meter lens
Pawl
ALNIA1609ZZ
MWI
THE METER CONTROL SWITCH IS INOPERATIVE
MWI-83
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
THE METER CONTROL SWITCH IS INOPERATIVE
Description
INFOID:0000000010435901
The meter control switches are inoperative when pressed.
Diagnosis Procedure
INFOID:0000000010435902
1.
CHECK METER CONTROL SWITCH SIGNAL
Check the meter control switch signal. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connector.
2.
CHECK METER CONTROL SWITCH
Check the meter control switch. Refer to
MWI-76, "Component Inspection"
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-86, "Removal and Installation"
NO
>> Replace meter control switch. Refer to
MWI-87, "Removal and Installation"
.
MWI-84
< SYMPTOM DIAGNOSIS >
THE STEERING SWITCHES ARE INOPERATIVE
THE STEERING SWITCHES ARE INOPERATIVE
Description
INFOID:0000000010435903
One or more of the steering switches to control the information display are inoperative.
Diagnosis Procedure
INFOID:0000000010435904
1.
CHECK STEERING SWITCH CIRCUIT
Check steering switch circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness or connector.
2.
CHECK STEERING SWITCH RESISTANCE
Check steering switch resistance. Refer to
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace steering switch. Refer to
3.
CHECK SPIRAL CABLE
Check spiral cable for continuity. Refer to
.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-86, "Removal and Installation"
NO
>> Replace spiral cable. Refer to
.
MWI
NORMAL OPERATING CONDITION
MWI-85
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
NORMAL OPERATING CONDITION
INFORMATION DISPLAY
INFORMATION DISPLAY : Description
INFOID:0000000010330003
OIL LEVEL
Oil level is not displayed after installation/removal of battery or combination meter. To display the oil level
again, follow the steps below.
1.
More than 5 minutes after turning key switch OFF, open the driver's door.
2.
Turn key switch ON.
AMBIENT AIR TEMPERATURE
The displayed ambient air temperature on the information display may differ from the actual temperature
because it is a corrected value calculated from the ambient sensor signal by the combination meter. Refer to
MWI-18, "INFORMATION DISPLAY : System Description"
for details on the correction process.
POSSIBLE DRIVING DISTANCE
The calculated possible driving distance may differ from the actual distance to empty if the refueling amount is
approximately 15 or less. This is because the refuel control (moves the fuel gauge segment quicker than
normal judging that the driver is refueling the vehicle) is not performed in such a case.
MWI-86
< REMOVAL AND INSTALLATION >
COMBINATION METER
REMOVAL AND INSTALLATION
COMBINATION METER
Removal and Installation
INFOID:0000000010330004
REMOVAL
1.
Disconnect the negative battery terminal. refer to
2.
Remove the cluster lid A. Refer to
.
3.
Remove screws (A), from the combination meter (1).
4.
Release the clips and remove the combination meter (1) from
the instrument panel.
: Clips
5.
Disconnect the harness connectors from the combination meter
and remove.
INSTALLATION
Installation is in the reverse order of removal.
ALNIA1607ZZ
ALNIA1608ZZ
MWI
METER CONTROL SWITCH
MWI-87
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
L
M
B
A
O
P
METER CONTROL SWITCH
Removal and Installation
INFOID:0000000010330005
REMOVAL
1.
Remove the instrument finisher (A). Refer to
.
2.
Remove the screws (A) and the meter control switch (1).
INSTALLATION
Installation is in the reverse order of removal.
ALNIA1585ZZ
MWI-88
< UNIT DISASSEMBLY AND ASSEMBLY >
COMBINATION METER
UNIT DISASSEMBLY AND ASSEMBLY
COMBINATION METER
Exploded View
INFOID:0000000010330006
Disassembly and Assembly
INFOID:0000000010330007
CAUTION:
• Do not touch the display, pointer, inside of combination meter or the printed area of the dial during
disassembly or assembly.
• Keep away from magnetic sources.
• Do not damage the combination meter lens.
DISASSEMBLY
1.
Remove the combination meter. Refer to
MWI-86, "Removal and Installation"
2.
Release pawls and remove the combination meter lens.
ASSEMBLY
Assembly is in the reverse order of disassembly.
1.
Combination meter
2.
Combination meter lens
Pawl
ALNIA1609ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст