Nissan Leaf. Manual — part 668
HAZARD SWITCH
EXL-273
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HAZARD SWITCH
Exploded View
INFOID:0000000010121501
Removal and Installation
INFOID:0000000010121502
REMOVAL
1. Remove cluster lid C. Refer to
IP-17, "Removal and Installation"
2. Disengage hazard switch fixing pawls, and then remove hazard switch.
INSTALLATION
Install in the reverse order of removal.
1.
Cluster lid C
2.
Hazard switch
: Pawl
JMLIA1658ZZ
EXL-274
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
REAR COMBINATION LAMP
REAR COMBINATION LAMP
Exploded View
INFOID:0000000010121503
REMOVAL
DISASSEMBLY
Removal and Installation
INFOID:0000000010121504
CAUTION:
• Fogging of rear combination lamp inside is not a malfunction. Never replace parts. Fogging is a
symptom in which inner surface of lens becomes whitely clouded, without there being visible water
drops or water spots, as if lens is made of frosted-glass.
1.
Rear combination lamp
2.
Grommet A
3.
Grommet B
: N·m (kg-m, in-lb)
JMLIA2083GB
1.
Rear combination lamp harness
2.
Rear turn signal bulb socket
3.
Rear turn signal bulb
4.
Buck-up lamp bulb socket
5.
Buck-up lamp bulb
6.
Rear combination lamp housing as-
sembly
JMLIA1778ZZ
REAR COMBINATION LAMP
EXL-275
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
REMOVAL
1. Remove luggage side lower finisher. Refer to
INT-43, "LUGGAGE SIDE LOWER FINISHER : Removal
2. Disconnect rear combination lamp connector.
3. Remove rear combination lamp mounting bolts.
4. Insert a shop cloth (B) into clearance (A) between rear combination lamp (1) and rear fender panel (2), or
apply protective tape.
CAUTION:
• To prevent rear fender panel paint surface from being damaged, always apply protection using a
shop cloth or protective tape.
• When using protective tape, apply protective tape to both rear fender panel and rear combination
lamp.
5. Pull rear combination lamp toward vehicle rear side, as shown
by the arrow in the figure.
6. Remove rear combination lamp.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
JMLIA2386ZZ
: Clip
JMLIA2385ZZ
EXL-276
< REMOVAL AND INSTALLATION >
[HALOGEN HEADLAMP]
REAR COMBINATION LAMP
When installing rear combination lamp, fix harness using harness fixing hook (A) on backside of rear
combination lamp housing and place harness toward vehicle inside so that harness is not pinched by
rear fender panel.
Replacement
INFOID:0000000010121505
CAUTION:
• Never touch the glass of bulb directly by hand. Keep grease and other oily matters away from it.
Never touch bulb by hand while it is lit or right after being turned off.
• Never leave bulb out of lamp reflector for a long time because dust, moisture smoke, etc. may affect
the performance of lamp. When replacing bulb, be sure to replace it with new one.
STOP/TAIL LAMP BULB
LED is used for stop/tail lamp bulb. Always replace rear combination lamp assembly as a unit, when bulb is to
be replaced because of malfunction.
REAR TURN SIGNAL LAMP BULB
1. Remove rear combination lamp mounting bolts.
2. Insert a shop cloth (B) into clearance (A) between rear combination lamp (1) and rear fender panel (2), or
apply protective tape.
CAUTION:
• To prevent rear fender panel paint surface from being damaged, always apply protection using a
shop cloth or protective tape.
1.
Harness
2.
Rear fender panel
3.
Rear fender extension
4.
Rear inner panel
: Vehicle front
JMLIA2387ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст