Nissan Leaf. Manual — part 417
RADIATOR CORE SUPPORT
DLK-163
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
5. Remove reservoir tank bolts (A), air guide (LH) clip (B) and
degas tank bolt (C).
6. Remove harness fixing clips (A).
7. Disconnect quick charge port connector. Refer to
VC-128, "Removal and Installation"
8. Disconnect normal charge port connector. Refer to
VC-135, "Removal and Installation"
9. Remove upper mounting bolts of charge port bracket.
10. Remove lower mounting nuts and bolt of radiator core support lower stay.
11. Move charge port bracket and radiator core support lower stay.
12. Support hood assembly using a suitable tool.
WARNING:
Injury may occur if hood assembly is not supported with appropriate material when removing
hood assembly.
13. Remove radiator core support upper bolts and radiator core support upper.
INSTALLATION
Installation is in the reverse order of removal.
RADIATOR CORE SUPPORT LOWER
RADIATOR CORE SUPPORT LOWER : Removal and Installation
INFOID:0000000010119860
DANGER:
Since hybrid vehicles and electric vehicles contain a high voltage battery, there is the risk of
electric shock, electric leakage, or similar accidents if the high voltage component and vehicle are
handled incorrectly. Be sure to follow the correct work procedures when performing inspection and
maintenance.
WARNING:
• Be sure to remove the service plug in order to disconnect the high voltage circuits before perform-
ing inspection or maintenance of high voltage system harnesses and parts.
• The removed service plug must always be carried in a pocket of the responsible worker or placed in
the tool box during the procedure to prevent the plug from being connected by mistake.
JMKIA6500ZZ
JMKIA9359ZZ
DLK-164
< REMOVAL AND INSTALLATION >
RADIATOR CORE SUPPORT
• Be sure to wear insulating protective equipment consisting of glove, shoes, face shield and glasses
before beginning work on the high voltage system.
• Never allow workers other than the responsible person to touch the vehicle containing high voltage
parts. To keep others from touching the high voltage parts, these parts must be covered with an insu-
lating sheet except when using them.
• Refer to
GI-34, "High Voltage Precautions"
.
CAUTION:
Never bring the vehicle into the READY status with the service plug removed unless otherwise
instructed in the Service Manual. A malfunction may occur if this is not observed.
REMOVAL
WARNING:
Disconnect the high voltage. Refer to
GI-33, "How to Disconnect High Voltage"
1. Check voltage in high voltage circuit. (Check that condenser are discharged.)
a. Lift up the vehicle and remove the Li-ion battery under covers. refer to
b. Disconnect high voltage connector from front side of Li-ion battery. Refer to
.
c.
Measure voltage between high voltage harness terminals.
DANGER:
Always use protective equipment as touching high
voltage components without using them will cause electro-
cution. (where high voltage might remain/is present on ter-
minals.)
CAUTION:
For voltage measurements, use a tester which can measure to 500V or higher.
2. Remove front bumper fascia, energy absorber, and apron bracket. Refer to
.
3. Remove reservoir tank bolts (A).
Standard
: 5 V or less
JSAIA1362ZZ
JMKIA6501ZZ
RADIATOR CORE SUPPORT
DLK-165
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
4. Remove harness fixing clips (A).
5. Disconnect quick charge port connector. Refer to
VC-128, "Removal and Installation"
6. Disconnect normal charge port connector. Refer to
VC-135, "Removal and Installation"
7. Remove lower mounting bolts of hood lock assembly.
8. Remove upper mounting bolts of charge port bracket.
9. Remove lower mounting nuts and bolt of radiator core support lower stay.
10. Move charge port bracket and radiator core support lower stay.
11. Remove air guides (LH/RH).
12. Use belts (A) to suspend radiator and condenser to prevent
them from falling.
CAUTION:
Do not damage radiator and condenser.
13. Remove front fixing clip of fender protector (LH/RH) from radiator core support lower.
14. Remove radiator core support lower bolts and radiator core support lower.
INSTALLATION
Installation is in the reverse order of removal.
RADIATOR UPPER GRILLE
RADIATOR UPPER GRILLE : Removal and Installation
INFOID:0000000010119861
REMOVAL
Remove radiator upper grille clips and radiator upper grille.
INSTALLATION
Installation in the reverse order of removal.
CHARGE PORT BRACKET
CHARGE PORT BRACKET : Removal and Installation
INFOID:0000000010119862
DANGER:
Since hybrid vehicles and electric vehicles contain a high voltage battery, there is the risk of
electric shock, electric leakage, or similar accidents if the high voltage component and vehicle are
JMKIA9359ZZ
JMKIA6502ZZ
DLK-166
< REMOVAL AND INSTALLATION >
RADIATOR CORE SUPPORT
handled incorrectly. Be sure to follow the correct work procedures when performing inspection and
maintenance.
WARNING:
• Be sure to remove the service plug in order to disconnect the high voltage circuits before perform-
ing inspection or maintenance of high voltage system harnesses and parts.
• The removed service plug must always be carried in a pocket of the responsible worker or placed in
the tool box during the procedure to prevent the plug from being connected by mistake.
• Be sure to wear insulating protective equipment consisting of glove, shoes, face shield and glasses
before beginning work on the high voltage system.
• Never allow workers other than the responsible person to touch the vehicle containing high voltage
parts. To keep others from touching the high voltage parts, these parts must be covered with an insu-
lating sheet except when using them.
• Refer to
GI-34, "High Voltage Precautions"
.
CAUTION:
Never bring the vehicle into the READY status with the service plug removed unless otherwise
instructed in the Service Manual. A malfunction may occur if this is not observed.
REMOVAL
WARNING:
Disconnect the high voltage. Refer to
GI-33, "How to Disconnect High Voltage"
1. Check voltage in high voltage circuit. (Check that condenser are discharged.)
a. Lift up the vehicle and remove the Li-ion battery under covers. refer to
b. Disconnect high voltage connector from front side of Li-ion battery. Refer to
.
c.
Measure voltage between high voltage harness terminals.
DANGER:
Always use protective equipment as touching high
voltage components without using them will cause electro-
cution. (where high voltage might remain/is present on ter-
minals.)
CAUTION:
For voltage measurements, use a tester which can measure to 500V or higher.
2. Remove charge port hinge assembly. Refer to
DLK-160, "CHARGE PORT LID HINGE ASSEMBLY :
.
3. Remove quick charge port. Refer to
VC-128, "Removal and Installation"
4. Remove normal charge port. Refer to
VC-135, "Removal and Installation"
.
5. Remove crash zone sensor. Refer to
SR-33, "Removal and Installation"
.
6. Remove harness fixing clips (A).
7. Remove charge port bracket bolts and nuts and charge port bracket.
Standard
: 5 V or less
JSAIA1362ZZ
JMKIA6503ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст