Nissan Leaf. Manual — part 869
FRONT DOOR FINISHER
INT-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
b. Disengage front door finisher fixing clips with a suitable tool (A).
CAUTION:
Insert a suitable tool between door panel and disengage
clips to prevent damage to the parts.
c. Remove front door finisher according to the numerical order 1
→
2 as shown in the figure.
d. Disconnect lock knob cable (1) and inside handle cable (2)
according to the numerical order 1
→ 4 as shown in the figure,
and then remove front door finisher.
5. Remove the following parts after removing the front door finisher.
• Remove front door sash inner cover.
Disengage front door sash inner cover fixing pawls according
to the numerical order 1
→ 3 as shown in the figure, and then
remove front door sash inner cover.
• Remove front power window main switch (driver) or front power window switch (passenger). Refer to
PWC-61, "Removal and Installation"
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Replace any deformed or damaged clips with same type and color.
• When installing, check in advance that clips are accurately aligned with the holes on door side, and
then install by pressing in.
: Clip
JMJIA5119ZZ
JMJIA5120ZZ
: Pawl
JMJIA5121ZZ
INT-22
< REMOVAL AND INSTALLATION >
REAR DOOR FINISHER
REAR DOOR FINISHER
Exploded View
INFOID:0000000010119665
Removal and Installation
INFOID:0000000010119666
CAUTION:
• When removing, always use a suitable tool that is made of plastic to prevent damage to the parts.
• Never damage the door panel.
REMOVAL
1. Fully open door window.
2. Remove rear power window switch finisher (LH) or rear power window switch finisher (RH).
1.
Rear door panel
2.
Rear door sash inner cover
3.
Rear door finisher
4.
Power window switch finisher
5.
Inside handle escutcheon
6.
Grommet
: Clip
: Pawl
: Vehicle front
AWJIA1049ZZ
REAR DOOR FINISHER
INT-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
a. Apply protective tape (A) on the parts to protect it from damage.
b. Disengage power window switch finisher fixing pawls with a suit-
able tool (A).
CAUTION:
Always insert a suitable tool from the rear of power window
switch finisher.
The parts may be damaged when inserting a suitable tool to
the front.
c. Pull up power window switch finisher and power window switch
as a unit and disconnect harness connector, and then remove
power window switch finisher.
3. Remove inside handle escutcheon.
Disengage inside handle escutcheon fixing pawl with a suitable
tool (A).
4. Remove rear door finisher.
a. Remove rear door finisher bolt (A) and rear door finisher screw
(B).
JMJIA6953ZZ
: Pawl
JMJIA6968ZZ
: Pawl
JMJIA5123ZZ
AWJIA1050ZZ
INT-24
< REMOVAL AND INSTALLATION >
REAR DOOR FINISHER
b. Disengage rear door finisher fixing clips with a suitable tool (A).
CAUTION:
Insert a suitable tool between door panel and disengage
clips to prevent damage to the parts.
c.
Remove rear door finisher according to the numerical order 1
→
2 as shown in the figure.
d. Disconnect lock knob cable (1) and inside handle cable (2)
according to the numerical order 1
→ 4 as shown in the figure,
and then remove rear door finisher.
5. Remove the following parts after removing the rear door finisher.
• Remove rear door sash inner cover.
Disengage rear door sash inner cover fixing pawls according
to the numerical order 1
→ 3 as shown in the figure, and then
remove rear door sash inner cover.
• Remove rear power window switch (LH) or rear power window switch (RH). Refer to
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Replace rear door finisher fixing clips with a new part after removal of rear door finisher. Never reuse
rear door finisher fixing clips.
• When installing, check in advance that clips are accurately aligned with the holes on door side, and
then install by pressing in.
: Clip
JMJIA5125ZZ
JMJIA5126ZZ
: Pawl
JMJIA6617ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст