Nissan Leaf. Manual — part 870
BODY SIDE TRIM
INT-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
BODY SIDE TRIM
Exploded View
INFOID:0000000010119667
INSTRUMENT SIDE PANEL
INSTRUMENT SIDE PANEL : Removal and Installation
INFOID:0000000010119668
CAUTION:
1.
Rear pillar finisher
2.
Rear body side welt
3.
Front body side welt
4.
Clip
5.
Front pillar garnish
6.
Metal clip A
7.
Dash side finisher
8.
Metal clip B
9.
Front kicking plate inner
10. Center pillar lower garnish
11. Rear kicking plate inner
12. Center pillar upper garnish
13. Instrument side panel
14. Front kicking plate outer
: Clip
: Pawl
: Metal clip
: Vehicle front
: Always replace after every disassembly.
JMJIA6619ZZ
INT-26
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
• When removing, always use a suitable tool that is made of plastic to prevent damage to the parts.
• Never damage the body.
REMOVAL
1. Apply protective tape (A) on the parts to protect it from damage.
2. Disengage instrument side panel fixing pawls with a suitable tool
(A) according to the numerical order 1
→ 2 as shown in the fig-
ure, and then remove instrument side panel.
INSTALLATION
Install in the reverse order of removal.
FRONT PILLAR GARNISH
FRONT PILLAR GARNISH : Removal and Installation
INFOID:0000000010119669
CAUTION:
• When removing, always use a suitable tool that is made of plastic to prevent damage to the parts.
• Never damage the body.
REMOVAL
1. Remove instrument side panel. Refer to
INT-25, "INSTRUMENT SIDE PANEL : Removal and Installa-
2. Remove front body side welt. Refer to
INT-29, "BODY SIDE WELT : Removal and Installation"
.
3. Remove front pillar garnish.
a. Disengage front pillar garnish fixing metal clip and clip with a
suitable tool (A) according to the numerical order 1
→ 2 as
shown in the figure.
JMJIA6954ZZ
: Pawl
JMJIA6977ZZ
: Clip
: Metal clip
JMJIA5129ZZ
BODY SIDE TRIM
INT-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
b. Cut clip anchor portion.
c. Pull front pillar garnish forward the direction of the arrow, discon-
nect tweeter harness connector and then remove front pillar gar-
nish.
NOTE:
Remove tweeter (if equipped) from front pillar garnish. Refer to
AV-321, "Removal and Installation"
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Replace clip anchor with a new part after removal. Never reuse clip anchor.
• When installing, check in advance that clip and metal clip are accurately aligned with the holes on
body side, and then install by pressing in.
KICKING PLATE OUTER
KICKING PLATE OUTER : Removal and Installation
INFOID:0000000010119670
CAUTION:
• When removing, always use a suitable tool that is made of plastic to prevent damage to the parts.
• Never damage the body.
REMOVAL
FRONT KICKING PLATE OUTER
1. Apply protective tape (A) on the parts to protect it from damage.
JMJIA5130ZZ
JMJIA5131ZZ
JMJIA6955ZZ
INT-28
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
2. Disengage front kicking plate outer fixing pawls with a suitable
tool (A), and then remove front kicking plate outer.
INSATALLATION
Install in the reverse order of removal.
KICKING PLATE INNER
KICKING PLATE INNER : Removal and Installation
INFOID:0000000010119671
CAUTION:
• When removing, always use a suitable tool that is made of plastic to prevent damage to the parts.
• Never damage the body.
REMOVAL
FRONT KICKING PLATE INNER
1. Apply protective tape (A) on the parts to protect it from damage.
2. Disengage front kicking plate inner fixing pawls with a suitable
tool (A) according to the numerical order 1
→ 5 as shown in the
figure, and then remove front kicking plate inner.
CAUTION:
Pawls may be damaged. Always remove from vehicle front.
REAR KICKING PLATE INNER
1. Apply protective tape (A) on the parts to protect it from damage.
: Pawl
JMJIA6978ZZ
JMJIA6956ZZ
: Pawl
JMJIA6979ZZ
JMJIA6957ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст