Nissan Leaf. Manual — part 718
GW-20
< REMOVAL AND INSTALLATION >
FRONT DOOR GLASS
6. Securely hold the front door glass and pull it out of the sash to
remove, as shown in the figure.
7. Remove lower sash.
8. Remove front door glass run.
INSTALLATION
Installation is in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000010119162
SYSTEM INITIALIZATION
Initialize the system if any of the following work is complete. Refer to
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator bolts, guide
rail bolts and glass bolts to correct the glass position.
JMKIA6427ZZ
FRONT REGULATOR
GW-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
FRONT REGULATOR
Exploded View
INFOID:0000000010119163
Removal and Installation
INFOID:0000000010119164
REMOVAL
1. Remove the front door glass. Refer to
GW-19, "Removal and Installation"
.
2. Disconnect the power window motor harness connector and harness clip.
3. Remove the front door regulator assembly bolts.
4. Remove the front door regulator assembly from the door panel,
as shown in the figure.
INSTALLATION
Installation is in the reverse order of removal.
1. Front door panel
2.
Sealing screen
3.
Front door glass run
4.
Front door regulator
5.
Power window motor
6.
Front door glass
7.
Lower sash
Front
JMKIA6425ZZ
JMKIA5808ZZ
GW-22
< REMOVAL AND INSTALLATION >
FRONT REGULATOR
Disassembly and Assembly
INFOID:0000000010119165
DISASSEMBLY
Remove the power window motor from the front door regulator.
INSPECTION AFTER REMOVAL
Check the front door regulator assembly for the following items. Replace or grease it if a malfunction is
detected.
• Wire wear
• Regulator deformation
ASSEMBLY
Assembly is in the reverse order of disassembly.
Inspection and Adjustment
INFOID:0000000010119166
Inspection after removal
Check the front regulator for the following items. Replace or grease it if a malfunction is detected.
• Wire wear
• Front regulator deformation
• Grease condition for each sliding part
SYSTEM INITIALIZATION
Initialize the system if any of the following work is complete. Refer to
FITTING INSPECTION
• Check that the glass is fit securely into the sash groove.
• Lower the glass slightly [approximately 10 to 20 mm (0.394 to 0.787 in)], and check that the clearance to the
sash is parallel. If the clearance between the glass and sash is not parallel, loosen the regulator bolts, guide
rail bolts and glass bolts to correct the glass position.
REAR DOOR GLASS
GW-23
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
GW
N
O
P
REAR DOOR GLASS
Exploded View
INFOID:0000000010119167
Removal and Installation
INFOID:0000000010119168
REMOVAL
1. Remove rear door finisher. Refer to
INT-22, "Removal and Installation"
.
2. Disconnect rear door speaker and remove the sealing screen.
NOTE:
Cut the butyl-tape so that some parts of the butyl-tape do not remain on the sealing screen, if the sealing
screen is reused.
3. Fully open rear door glass.
4. Remove partition sash mounting bolts and screw.
5. Reconnect the power window switch and operate the power window switch to raise the door window until
the rear door glass bolts can be seen.
6. Loosen the rear door glass bolts.
1.
Rear door panel
2.
Rear door glass run
3.
Sealing screen
4.
Rear door regulator
5.
Power window motor
6.
Partition glass
7.
Partition sash
8.
Rear door glass
Front
JMKIA6426ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст