Nissan Leaf. Manual — part 873
HEADLINING
INT-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
Removal and Installation
INFOID:0000000010119680
CAUTION:
• When removing, always use a suitable tool that is made of plastic to prevent damage to the parts.
• Never damage the body.
REMOVAL
1. Remove front pillar garnish (LH and RH). Refer to
INT-26, "FRONT PILLAR GARNISH : Removal and
.
2. Disconnect harness connectors (A) from headlining and harness clips.
3. Remove center pillar upper garnish (LH and RH). Refer to
INT-31, "CENTER PILLAR UPPER GARNISH :
.
4. Remove rear pillar finisher. (LH and RH). Refer to
INT-31, "REAR PILLAR FINISHER : Removal and
.
5. Disconnect harness connectors (A) from headlining and harness
clips.
10. Room lamp assembly
11. Rear assist grip LH
12. Headlining clip
13. Metal clip
14. Dual lock fastener
15. Bracket
16. Map lamp plate
17. Map lamp assembly
18. Lens
: Clip
: Pawl
: Metal clip
1.
Left side pillar
2.
Right side pillar
: Clip
JMJIA6618ZZ
: Clip
JMJIA5144ZZ
INT-38
< REMOVAL AND INSTALLATION >
HEADLINING
6. Remove all assist grips.
a. Remove assist grip clip
i.
Disengage pawl of assist grip clip (1) using a suitable tool (A)
according to the numerical order 1 as shown in the figure.
ii.
Slide assist grip clip forward according to the numerical order 2
as shown in the figure, and then remove assist grip clip.
b. Slide assist grip (2) forward and remove it.
c.
Remove metal clips.
7. Remove sun visor assembly (LH and RH).
a. Disengage sun visor cover fixing pawls with a suitable tool (A),
and then remove sun visor cover.
b. Remove sun visor assembly screws, and then remove sun visor assembly.
8. Remove room lamp assembly. Refer to
INL-53, "Removal and Installation"
.
9. Remove lamp unit of map lamp assembly. Refer to
INL-52, "Removal and Installation"
.
CAUTION:
The map lamp assembly can only be removed from back side after headlining is removed.
10. Remove sun visor holder (LH and RH).
a. Rotate 90
° according to the numerical order 1 as shown in the
figure.
b. Remove toward vehicle lower according to the numerical order 2
as shown in the figure.
11. Disengage bracket fixing dual lock fastener (A).
12. Disengage map lamp fixing metal clips.
13. Remove headlining clips.
: Pawl
: Pawl
JMJIA4398ZZ
JMJIA4399ZZ
JMJIA4401ZZ
: Metal clip
JMJIA5142ZZ
HEADLINING
INT-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
14. Remove headlining assembly through the back door.
CAUTION:
• Two workers are required for removal in order to prevent
damage.
• Apply protective tape to the portion where contact may
occur during work.
• Never bend headlining when removing to prevent damage
to the parts.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When installing headlining, start by installing both sun visor holders and headlining clips in order to
keep the headlining in position.
• Never bend headlining when installing to prevent damage to the parts.
• Be careful that the surface is not wrinkled when installing.
JMJIA5143ZZ
INT-40
< REMOVAL AND INSTALLATION >
LUGGAGE FLOOR TRIM
LUGGAGE FLOOR TRIM
Exploded View
INFOID:0000000010119681
REAR PARCEL SHELF FINISHER
REAR PARCEL SHELF FINISHER : Removal and Installation
INFOID:0000000010119682
REMOVAL
1. Remove strap from back door side finisher hook.
1.
Luggage side lower finisher RH
2.
Luggage finisher mask RH
3.
Luggage floor upper finisher
4.
Luggage floor front finisher
5.
Luggage finisher mask LH
6.
Luggage side lower finisher LH
7.
Luggage side box
8.
Luggage rear plate
9.
Luggage side lower bracket
10. Shock absorber mask RH
11. Luggage hook
12. Luggage room lamp
13. Rear parcel shelf finisher
14. Shock absorber mask LH
15. Tool lid mask
16. Luggage floor board
17. Net hook pin
: Clip
: Pawl
: Metal clip
JMJIA5052ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст