Nissan Leaf. Manual — part 871
BODY SIDE TRIM
INT-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
2. Disengage rear kicking plate inner fixing pawls with a suitable
tool (A) according to the numerical order 1
→ 5 as shown in the
figure, and then remove rear kicking plate inner.
CAUTION:
Pawls may be damaged. Always remove from vehicle front.
INSATALLATION
Note the following item. and install in the reverse order of removal.
CAUTION:
The parts cannot be installed when the vehicle side metal clip (A) and metal clip (B) are not aligned
normally. Check that the positions of metal clip (A) and metal clip (B) are correct. Refer to
BODY SIDE WELT
BODY SIDE WELT : Removal and Installation
INFOID:0000000010119672
CAUTION:
• Never excessively pull body side welt to prevent damage to the parts.
• Never damage the body.
REMOVAL
FRONT BODY SIDE WELT
1. Remove center pillar lower garnish. Refer to
INT-30, "CENTER PILLAR LOWER GARNISH : Removal
2. Remove front body side welt.
REAR BODY SIDE WELT
1. Remove center pillar lower garnish. Refer to
INT-30, "CENTER PILLAR LOWER GARNISH : Removal
2. Remove rear body side welt.
INSTALLATION
Install in the reverse order of removal.
DASH SIDE FINISHER
DASH SIDE FINISHER : Removal and Installation
INFOID:0000000010119673
CAUTION:
Never damage the body.
REMOVAL
1. Remove front kicking plate inner. Refer to
INT-28, "KICKING PLATE INNER : Removal and Installation"
2. Remove front body side welt. Refer to
INT-29, "BODY SIDE WELT : Removal and Installation"
.
3. Remove dash side finisher.
: Pawl
JMJIA6980ZZ
INT-30
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
a. Disengage stud bolt (A).
b. Pull back dash side finisher, and then disengage dash side fin-
isher fixing pawls, and then remove dash side finisher.
CAUTION:
Pull dash side finisher straight toward vehicle rear. Other-
wise, pawls may be damaged if front end of dash side fin-
isher opens toward vehicle inside.
INSTALLATION
Install in the reverse order of removal.
CENTER PILLAR LOWER GARNISH
CENTER PILLAR LOWER GARNISH : Removal and Installation
INFOID:0000000010119674
CAUTION:
• When removing, always use a suitable tool that is made of plastic to prevent damage to the parts.
• Never damage the body.
REMOVAL
1. Fully open front door and rear door.
2. Slide front seat to the fully forward position. Tilt seatback forward.
3. Remove front kicking plate inner and rear kicking plate inner. Refer to
INT-28, "KICKING PLATE INNER :
.
4. Remove center pillar lower garnish.
Disengage center pillar lower garnish fixing clips with a suitable
tool (A), and then remove center pillar lower garnish.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing, check in advance that clips are accurately aligned with the holes on body side, and
then install by pressing in.
CENTER PILLAR UPPER GARNISH
JMJIA6101ZZ
: Pawl
JMJIA5135ZZ
: Clip
JMJIA5136ZZ
BODY SIDE TRIM
INT-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
INT
N
O
P
CENTER PILLAR UPPER GARNISH : Removal and Installation
INFOID:0000000010119675
CAUTION:
• When removing, always use a suitable tool that is made of plastic to prevent damage to the parts.
• Never damage the body.
REMOVAL
1. Remove front seat belt shoulder anchor. Refer to
SB-11, "SEAT BELT RETRACTOR : Removal and Instal-
.
2. Remove center pillar lower garnish. Refer to
INT-30, "CENTER PILLAR LOWER GARNISH : Removal
3. Remove front body side welt and rear body side welt. refer to
INT-29, "BODY SIDE WELT : Removal and
.
4. Remove center pillar upper garnish.
a. Disengage center pillar upper garnish lower side fixing clip with
a suitable tool (A).
b. Disengage center pillar upper garnish upper side fixing pawl, and then remove center pillar upper garnish.
NOTE:
Removal operation can be performed easily according to the numerical order 1
→ 4 as shown in the figure
when pressing pawl by inserting a removal tool from direction (A) as shown in the figure.
CAUTION:
Be careful not to apply excessive force when removing center pillar upper garnish. Otherwise,
pawl may be damaged and fragments may drop in panel holes on body.
INATALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Replace center pillar upper garnish with a new part after removal. Never reuse center pillar upper
garnish.
• When installing, check in advance that clip and pawl are accurately aligned with the holes on body
side, and then install by pressing in.
REAR PILLAR FINISHER
REAR PILLAR FINISHER : Removal and Installation
INFOID:0000000010119676
CAUTION:
• When removing, always use a suitable tool that is made of plastic to prevent damage to the parts.
• Never damage the body.
REMOVAL
: Clip
: Pawl
JMJIA5137ZZ
PIIB7674J
INT-32
< REMOVAL AND INSTALLATION >
BODY SIDE TRIM
1. Fully open rear door and back door.
2. Remove rear body side welt. Refer to
INT-29, "BODY SIDE WELT : Removal and Installation"
3. Remove back door weather-strip. Refer to
DLK-185, "BACK DOOR WEATHER-STRIP : Removal and
.
4. Remove rear parcel shelf finisher. Refer to
INT-40, "REAR PARCEL SHELF FINISHER : Removal and
.
5. Remove luggage side lower finisher. Refer to
INT-43, "LUGGAGE SIDE LOWER FINISHER : Removal
6. Remove rear seat belt anchor bolt. Refer to
SB-16, "SEAT BELT RETRACTOR : Removal and Installa-
7. Remove rear pillar finisher.
Disengage rear pillar finisher fixing clips with a suitable tool (A),
and then remove rear pillar finisher.
CAUTION:
Be careful not to damage parts when inserting seat belt
anchor bolt into seat belt opening hole of rear pillar finisher.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When installing, check in advance that clips are accurately aligned with the holes on body side, and
then install by pressing in.
: Clip
JMJIA5138ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст