Nissan Leaf. Manual — part 420
REAR DOOR
DLK-175
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR
Exploded View
INFOID:0000000010119871
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000010119872
CAUTION:
• Use two people when removing or installing the rear door due to its heavy weight.
• When removing or installing the rear door assembly, support the rear door using a suitable tool.
REMOVAL
1. Remove rear door harness grommet (2) from body side outer (1)
and pull out rear door harness.
1.
Rear door panel
2.
Grommet
3.
Bolt
4.
Door striker
5.
Bumper rubber
6.
Door check link
7.
Door hinge (lower)
8.
Door hinge (upper)
Do not reuse
Grease
AWKIA2404ZZ
JMKIA6418ZZ
DLK-176
< REMOVAL AND INSTALLATION >
REAR DOOR
2. Disconnect the harness connector from the rear door.
3. Remove the door check link bolt (body side).
4. Remove door hinge nuts (door side) and rear door assembly.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• After installation, check the rear door open/close and lock/unlock operation. If necessary, perform
the rear door assembly adjustment procedure. Refer to
DLK-177, "DOOR ASSEMBLY : Adjustment"
.
• Check door hinge rotating part for poor lubrication. If necessary, apply a suitable multi-purpose
grease.
• After installation, apply touch-up paint (body color) to the head of door hinge nuts.
JMKIA6419ZZ
REAR DOOR
DLK-177
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR ASSEMBLY : Adjustment
INFOID:0000000010119873
Check the clearance and surface height between rear door and each part by visual inspection and tactile feel.
If the clearance and the surface height are out of specification, adjust them according to the adjustment proce-
dure.
Unit: mm (in)
FITTING ADJUSTMENT PROCEDURE
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
Bolt
7.
Front door hinge
8.
Rear door hinge (upper)
9.
Rear door hinge (lower)
Do not reuse
Grease
Portion
Section
Measurement
Standard
Front fender – Front door
A – A
Clearance
4.0
± 1.0 (0.16 ± 0.04)
Surface height
0.0
± 1.0 (0.00 ± 0.04)
Front door – Rear door
B – B
Clearance
4.2
± 1.0 (0.17 ± 0.04)
Surface height
0.0
± 1.0 (0.00 ± 0.04)
Front door – Rear door
C – C
Clearance
4.0
± 1.0 (0.16 ± 0.04)
Surface height
0.0
± 1.0 (0.00 ± 0.04)
AWKIA2364ZZ
DLK-178
< REMOVAL AND INSTALLATION >
REAR DOOR
1. Remove center pillar lower garnish. Refer to
INT-30, "CENTER PILLAR LOWER GARNISH : Removal
2. Loosen door hinge nuts (door side).
3. Adjust the surface height of rear door according to the specifications provided.
4. Temporarily tighten door hinge nuts (door side).
5. Loosen door hinge nuts and bolts (body side).
6. Raise rear door at rear end to adjust clearance of rear door according to the specifications provided.
7. Tighten bolts and nuts to the specified torque.
CAUTION:
• After installation, apply touch-up paint (body color) to the head of door hinge bolts and nuts.
• Check door hinge rotating part for poor lubrication. If necessary, apply a suitable multi-purpose
grease.
8. Install center pillar lower garnish. Refer to
INT-30, "CENTER PILLAR LOWER GARNISH : Removal and
.
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000010119874
REMOVAL
Remove the door striker bolts and door striker.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Do not reuse door striker bolts.
• After installation, perform the rear door adjustment procedure. Refer to
.
• After installation, apply touch-up paint (body color) to the head of the door striker bolts.
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000010119875
CAUTION:
• Use two people when removing or installing the rear door due to its heavy weight.
• When removing and installing rear door assembly, support the rear door using a suitable tool.
REMOVAL
1. Remove rear door assembly. Refer to
DLK-175, "DOOR ASSEMBLY : Removal and Installation"
2. Remove center pillar lower garnish. Refer to
INT-30, "CENTER PILLAR LOWER GARNISH : Removal
3. Remove the rear door hinge bolts and nuts (body side) and door hinge.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• After installation, check the rear door open/close and lock/unlock operation. If necessary, perform
the rear door assembly adjustment procedure. Refer to
DLK-177, "DOOR ASSEMBLY : Adjustment"
.
• After installation, apply touch-up paint (body color) to the head of door hinge nuts.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст