Nissan Leaf. Manual — part 770
SYSTEM SETTING
HAC-83
< BASIC INSPECTION >
[AUTO A/C (WITH HEAT PUMP)]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
SYSTEM SETTING
Temperature Setting Trimmer
INFOID:0000000010121783
DESCRIPTION
If the temperature felt by the customer is different from the air flow temperature controlled by the temperature
setting, the A/C auto amp. control temperature can be adjusted to compensate for the temperature setting.
HOW TO SET
With CONSULT
Perform “TEMP SET CORRECT” in “Work support” of “HVAC”.
NOTE:
• When
−3.0°C (−6°F) is corrected on the temperature setting set as 25.0°C (77°F) the temperature controlled
by A/C auto amp. is 25.0
°C (77°F) −3.0°C (−6°F) = 22.0°C (72°F) and the temperature becomes lower than
the temperature setting.
• When the 12V battery cable is disconnected from the negative terminal or when the 12V battery voltage
becomes 10 V or less, the setting of the difference between the set temperature and control temperature
may be cancelled.
Inlet Port Memory Function (REC)
INFOID:0000000010121784
DESCRIPTION
• If the ignition switch is turned to the OFF position while the intake switch is set to ON (recirculation), “Per-
form the memory” or “Do not perform the memory” of intake switch ON (recirculation) condition can be
selected.
• If “Perform the memory” is set, the intake switch is ON (recirculation) when turning the ignition switch to the
ON position again.
• If “Do not perform the memory” is set, the air inlets is controlled automatically when turning the ignition
switch to the ON position again.
HOW TO SET
With CONSULT
Perform the “REC MEMORY SET” in “Work support” of “HVAC”.
NOTE:
Work support items
Display (
°C)
Display (
°F)
TEMP SET CORRECT
3.0
6
2.5
5
2.0
4
1.5
3
1.0
2
0.5
1
0 (initial status)
0 (initial status)
−0.5
−1
−1.0
−2
−1.5
−3
−2.0
−4
−2.5
−5
−3.0
−6
Work support items
Display
Setting
REC MEMORY SET
WITHOUT (initial status)
Perform the memory of manual REC
WITH
Do not perform the memory of manual REC (auto control)
HAC-84
< BASIC INSPECTION >
[AUTO A/C (WITH HEAT PUMP)]
SYSTEM SETTING
When the 12V battery cable is disconnected from the negative terminal or when the 12V battery voltage
becomes 10 V or less, the setting of the REC memory function may be cancelled.
Inlet Port Memory Function (FRE)
INFOID:0000000010121785
DESCRIPTION
• If the ignition switch is turned to the OFF position while the intake switch is set to OFF (fresh air intake), “Per-
form the memory” or “Do not perform the memory” of intake switch OFF (fresh air intake) condition can be
selected.
• If “Perform the memory” is set, the intake switch is OFF (fresh air intake) when turning the ignition switch to
the ON position again.
• If “Do not perform the memory” is set, the air inlets is controlled automatically when turning the ignition
switch to the ON position again.
HOW TO SET
With CONSULT
Perform the “FRE MEMORY SET” in “Work support” of “HVAC”.
NOTE:
When the 12V battery cable is disconnected from the negative terminal or when the 12V battery voltage
becomes 10 V or less, the setting of the FRE memory function may be cancelled.
Foot Position Setting Trimmer
INFOID:0000000010121786
DESCRIPTION
In FOOT mode, the air blowing to DEF can change ON/OFF.
HOW TO SET
With CONSULT
Perform the “BLOW SET” in “Work support” of “HVAC”.
NOTE:
When the 12V battery cable is disconnected from the negative terminal or when the 12V battery voltage
becomes 10 V or less, the setting of the discharge air mix ratio in FOOT mode may be cancelled.
Compressor Operation Setting at Defroster Mode (Timer/Remote Climate Control)
INFOID:0000000010121787
DESCRIPTION
For A/C-heater timer and remote climate control, change the setting of electric compressor operation during
DEF mode.
How to set
Using CONSULT, select “COMP OPRT SET AT DEF MODE (TIM/RMT CLIMT CONT)” in “Work Support“ of
“HVAC”.
Work support items
Display
Setting
FRE MEMORY SET
WITHOUT
Perform the memory of manual FRE
WITH (initial status)
Do not perform the memory of manual FRE (auto control)
Work support items
Display
Defroster door position
Audio control
Manual control
BLOW SET
Mode1 (initial status)
OPEN
CLOSE
Mode2
OPEN
OPEN
Mode3
CLOSE
OPEN
Mode4
CLOSE
CLOSE
SYSTEM SETTING
HAC-85
< BASIC INSPECTION >
[AUTO A/C (WITH HEAT PUMP)]
C
D
E
F
G
H
J
K
L
M
A
B
HAC
N
O
P
Setting of Compressor Maximum Rotation Speed During Pre Air Conditioning
INFOID:0000000010121788
DESCRIPTION
The compressor maximum rotation speed during remote or timer air conditioning can be adjusted.
How to set
Using CONSULT, select ”TARGET MAX RPM ADJ AT PRE-CLIMATE“ in ”Work support“ for ”HVAC“.
Setting of Compressor Maximum Rotation Speed During Idling
INFOID:0000000010121789
DESCRIPTION
The electric compressor maximum rotation speed during idling can be adjusted.
How to set
Using CONSULT, select ”TARGET MAX RPM ADJ AT IDL“ in ”Work support“ of ”HVAC“.
Work support items
Display
Setup
COMP OPRT SET AT DEF MODE (TIM/RMT
CLIMT CONT)
OFF
During DEF mode operation, the electric compressor
stops.
ON
During DEF mode operation, the electric compressor op-
erates.
Work support items
Note
TARGET MAX RPM ADJ AT PRE-CLIMATE
Raising set value: Improve the cooling performance.
Lowering set value: Reduce the operation noise level.
Work support items
Note
TARGET MAX RPM ADJ AT IDL
Raising set value: Improve the cooling performance.
Lowering set value: Reduce the operation noise level.
HAC-86
< BASIC INSPECTION >
[AUTO A/C (WITH HEAT PUMP)]
DOOR MOTOR STARTING POSITION RESET
DOOR MOTOR STARTING POSITION RESET
Description
INFOID:0000000010121790
• Reset signal is transmitted from A/C auto amp. to air mix door motor and mode door motor. Starting position
reset can be performed.
NOTE:
During reset, DEF switch indicator blinks.
• When air mix door motor or mode door motor is removed and installed, always perform door motor starting
position reset.
Work Procedure
INFOID:0000000010121791
1.
PERFORM DOOR MOTOR STARTING POSITION RESET
With CONSULT
1. Turn ignition switch ON.
2. Select “Door Motor Starting Position Reset” in “Work support” of “HVAC” using CONSULT.
3. Touch “Start” and wait a few seconds.
4. Make sure the “COMPLETED” is displayed on CONSULT screen.
>> Inspection End.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст