Nissan Leaf. Manual — part 1264
VTL-6
< PRECAUTION >
PRECAUTIONS
Indicate "HIGH VOLTAGE. DO NOT TOUCH" on the vehicle under repair/inspection to call attention to other
workers.
Precaution for Removing 12V Battery
INFOID:0000000010120482
1. Check that EVSE is not connected.
NOTE:
If EVSE is connected, the air conditioning system may be automatically activated by the timer A/C func-
tion.
2. Turn the power switch OFF
→ ON → OFF. Get out of the vehicle. Close all doors (including back door).
JSAIA1600GB
PRECAUTIONS
VTL-7
< PRECAUTION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
3. Check that the charge status indicator lamp does not blink and wait for 5 minutes or more.
NOTE:
If the battery is removed within 5 minutes after the power switch is turned OFF, plural DTCs may be
detected.
4. Remove 12V battery within 1 hour after turning the power switch OFF
→ ON → OFF.
NOTE:
• The 12V battery automatic charge control may start automatically even when the power switch is in
OFF state.
• Once the power switch is turned ON
→ OFF, the 12V battery automatic charge control does not start for
approximately 1 hour.
CAUTION:
• After all doors (including back door) are closed, if a door (including back door) is opened before
battery terminals are disconnected, start over from Step 1.
• After turning the power switch OFF, if “Remote A/C” is activated by user operation, stop the air
conditioner and start over from Step 1.
Precaution for Work
INFOID:0000000010120483
• When removing or disassembling each component, be careful not to damage or deform it. If a component
may be subject to interference, be sure to protect it with a shop cloth.
• When removing (disengaging) components with a screwdriver or similar tool, be sure to wrap the component
with a shop cloth or vinyl tape to protect it.
• Protect the removed parts with a shop cloth and prevent them from being dropped.
• Replace a deformed or damaged clip.
• If a part is specified as a non-reusable part, always replace it with a new one.
• Be sure to tighten bolts and nuts securely to the specified torque.
• After installation is complete, be sure to check that each part works properly.
• Follow the steps below to clean components:
- Water soluble dirt:
• Dip a soft cloth into lukewarm water, wring the water out of the cloth and wipe the dirty area.
• Then rub with a soft, dry cloth.
- Oily dirt:
• Dip a soft cloth into lukewarm water with mild detergent (concentration: within 2 to 3%) and wipe the dirty
area.
• Then dip a cloth into fresh water, wring the water out of the cloth and wipe the detergent off.
• Then rub with a soft, dry cloth.
- Do not use organic solvent such as thinner, benzene, alcohol or gasoline.
- For genuine leather seats, use a genuine leather seat cleaner.
VTL-8
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000010120484
The actual shape of the tools may differ from those illustrated here.
Commercial Service Tool
INFOID:0000000010120485
Tool number
(TechMate No.)
Tool name
Description
—
(J-46534)
Trim Tool Set
Removing trim components
AWJIA0483ZZ
(TechMate No.)
Tool name
Description
( — )
Power tool
Loosening nuts, screws and bolts
PIIB1407E
IN-CABIN MICROFILTER
VTL-9
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
PERIODIC MAINTENANCE
IN-CABIN MICROFILTER
Exploded View
INFOID:0000000010120486
Removal and Installation
INFOID:0000000010120487
REMOVAL
NOTE:
When removing in-cabin microfilter, visually check the operation through glove box mask opening.
1. Remove instrument under cover RH. Refer to
.
2. Remove instrument lower cover RH. Refer to
3. Open glove box lid.
4. Disengage pawls, and then remove glove box mask (1).
5. Disengage pawl, and then remove filter cover (1) from heating
and cooling unit assembly.
1.
Heating and cooling unit assembly
2.
In-cabin microfilter
3.
Filter cover
JPIIA1807ZZ
: Pawl
JPIIA1844ZZ
: Pawl
JPIIA1845ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст