Nissan Leaf. Manual — part 998
PG-4
< PRECAUTION >
PRECAUTIONS
dled incorrectly. Be sure to follow the correct work procedures when performing inspection and
maintenance.
• Be sure to remove the service plug in order to disconnect the high voltage circuits before perform-
ing inspection or maintenance of high voltage system harnesses and parts.
• To prevent the removed service plug from being connected by mistake during the procedure, always
carry it in your pocket or put it in the tool box.
• Be sure to wear insulating protective equipment before beginning work on the high voltage system.
• Clearly identify the persons responsible for high voltage work and ensure that other persons do not
touch the vehicle. When not working, cover high voltage parts with an insulating cover sheet or sim-
ilar item to prevent other persons from contacting them.
CAUTION:
There is the possibility of a malfunction occurring if the vehicle is changed to READY status while the
service plug is removed. Therefore do not change the vehicle to READY status unless instructed to do
so in the Service Manual.
HIGH VOLTAGE HARNESS AND EQUIPMENT IDENTIFICATION
The colors of the high voltage harnesses and connectors are all orange. Orange "High Voltage" labels are
applied to the Li-ion battery and other high voltage devices. Do not carelessly touch these harnesses and
parts.
HANDLING OF HIGH VOLTAGE HARNESS AND TERMINALS
Immediately insulate disconnected high voltage connectors and terminals with insulating tape.
REGULATIONS ON WORKERS WITH MEDICAL ELECTRONICS
WARNING:
The vehicle contains parts that contain powerful magnets. If a person who is wearing a heart pace-
maker or other medical device is close to these parts, the medical device may be affected by the mag-
nets. Such persons must not perform work on the vehicle.
PROHIBITED ITEMS TO CARRY DURING THE WORK
Because this vehicle uses components that contain high voltage and powerful magnetism, due not carry any
metal products which may cause short circuits, or any magnetic media (cash cards, prepaid cards, etc.) which
may be damaged on your person when working.
POSTING A SIGN OF “DANGER! HIGH VOLTAGE AREA. KEEP OUT”
PG
PRECAUTIONS
PG-5
< PRECAUTION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
To call the attention of other workers, indicate "High voltage work in progress. Do not touch!" on vehicles
where work is being performed on the high voltage systems.
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000010119354
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
JSAIA1600GB
PG-6
< PRECAUTION >
PRECAUTIONS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SR and SB section of this Service Man-
ual.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Airbag Diagnosis Sensor Unit or other Airbag System sensors with the Igni-
tion ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s) with a
hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the Ignition OFF, disconnect the
battery and wait at least three minutes before performing any service.
Precaution for Removing 12V Battery
INFOID:0000000010119355
1. Check that EVSE is not connected.
NOTE:
If EVSE is connected, the air conditioning system may be automatically activated by the timer A/C func-
tion.
2. Turn the power switch OFF
→ ON → OFF. Get out of the vehicle. Close all doors (including back door).
3. Check that the charge status indicator lamp does not blink and wait for 5 minutes or more.
NOTE:
If the battery is removed within 5 minutes after the power switch is turned OFF, plural DTCs may be
detected.
4. Remove 12V battery within 1 hour after turning the power switch OFF
→ ON → OFF.
NOTE:
• The 12V battery automatic charge control may start automatically even when the power switch is in
OFF state.
• Once the power switch is turned ON
→ OFF, the 12V battery automatic charge control does not start for
approximately 1 hour.
CAUTION:
• After all doors (including back door) are closed, if a door (including back door) is opened before
battery terminals are disconnected, start over from Step 1.
• After turning the power switch OFF, if “Remote A/C” is activated by user operation, stop the air
conditioner and start over from Step 1.
PG
PREPARATION
PG-7
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000010119356
The actual shape of the tools may differ from those illustrated here.
Tool number
(TechMate No.)
Tool name
Description
—
(—) Model GR8-1200 NI
Multitasking battery and electrical di-
agnostic station
Tests batteries, starting and charging sys-
tems and charges batteries.
For operating instructions, refer to diagnostic
station instruction manual.
—
(—) Model EXP-800 NI
Battery and electrical diagnostic ana-
lyzer
Tests batteries and charging systems.
For operating instructions, refer to diagnostic
analyzer instruction manual.
AWIIA1239ZZ
JSMIA0806ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст