Nissan Juke (2014 year). Service Repair Manual — part 51
DOOR & LOCK SYSTEM
DLK-41
< WIRING DIAGRAM >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
JRKWC9387GB
Revision: 2013 October
2014 JUKE
DLK-42
< WIRING DIAGRAM >
[WITH INTELLIGENT KEY SYSTEM]
DOOR & LOCK SYSTEM
JRKWC9388GB
Revision: 2013 October
2014 JUKE
DOOR & LOCK SYSTEM
DLK-43
< WIRING DIAGRAM >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
JRKWC9389GB
Revision: 2013 October
2014 JUKE
DLK-44
< WIRING DIAGRAM >
[WITH INTELLIGENT KEY SYSTEM]
DOOR & LOCK SYSTEM
JRKWC9390GB
Revision: 2013 October
2014 JUKE
DOOR & LOCK SYSTEM
DLK-45
< WIRING DIAGRAM >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
JRKWC9391GB
Revision: 2013 October
2014 JUKE
DLK-46
< WIRING DIAGRAM >
[WITH INTELLIGENT KEY SYSTEM]
DOOR & LOCK SYSTEM
JRKWC9392GB
Revision: 2013 October
2014 JUKE
DOOR & LOCK SYSTEM
DLK-47
< WIRING DIAGRAM >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
JRKWC9393GB
Revision: 2013 October
2014 JUKE
DLK-48
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS AND REPAIR WORK FLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORK FLOW
Work Flow
INFOID:0000000009753945
OVERALL SEQUENCE
DETAILED FLOW
JMKIA8652GB
Revision: 2013 October
2014 JUKE
DIAGNOSIS AND REPAIR WORK FLOW
DLK-49
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
GET INFORMATION FOR SYMPTOM
1.
Get detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurs).
2.
Check operation condition of the function that is malfunctioning.
>> GO TO 2.
2.
CHECK DTC
1.
Check DTC.
2.
Perform the following procedure if DTC is detected.
-
Record DTC and freeze frame data (Print them out using CONSULT.)
-
Erase DTC.
-
Study the relationship between the cause detected by DTC and the symptom described by the customer.
3.
Check related service bulletins for information.
Are any symptoms described and any DTC detected?
Symptom is described, DTC is detected>>GO TO 3.
Symptom is described, DTC is not detected>>GO TO 4.
Symptom is not described, DTC is detected>>GO TO 5.
3.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Also study the normal operation and fail-safe related to the symptom.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.
CONFIRM THE SYMPTOM
Try to confirm the symptom described by the customer.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.
PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC CONFIRMATION PROCEDURE for the detected DTC, and then check that DTC is detected
again. At this time, always connect CONSULT to the vehicle, and check self diagnostic results in real time.
If two or more DTCs are detected, refer to
BCS-58, "DTC Inspection Priority Chart"
(BCM), and determine
trouble diagnosis order.
NOTE:
• Freeze frame data is useful if the DTC is not detected.
• Perform Component Function Check if DTC CONFIRMATION PROCEDURE is not included on Service
Manual. This simplified check procedure is an effective alternative though DTC cannot be detected during
this check.
If the result of Component Function Check is NG, it is the same as the detection of DTC by DTC CONFIR-
MATION PROCEDURE.
Is DTC detected?
YES
>> GO TO 7.
NO
>> Check according to
GI-46, "Intermittent Incident"
.
6.
DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS
Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step
4, and determine the trouble diagnosis order based on possible causes and symptom.
Is the symptom described?
YES
>> GO TO 7.
NO
>> Monitor input data from related sensors or check voltage of related module terminals using CON-
SULT.
7.
DETECT MALFUNCTIONING PART BY DIAGNOSIS PROCEDURE
Revision: 2013 October
2014 JUKE
DLK-50
< BASIC INSPECTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS AND REPAIR WORK FLOW
Inspect according to Diagnosis Procedure of the system.
Is malfunctioning part detected?
YES
>> GO TO 8.
NO
>> Check according to
GI-46, "Intermittent Incident"
.
8.
REPAIR OR REPLACE THE MALFUNCTIONING PART
1.
Repair or replace the malfunctioning part.
2.
Reconnect parts or connectors disconnected during Diagnosis Procedure again after repair and replace-
ment.
3.
Check DTC. If DTC is detected, erase it.
>> GO TO 9.
9.
FINAL CHECK
When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the
malfunction is repaired securely.
When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the
symptom is not detected.
Is DTC detected and does symptom remain?
YES-1 >> DTC is detected: GO TO 7.
YES-2 >> Symptom remains: GO TO 4.
NO
>> Before returning the vehicle to the customer, always erase DTC.
Revision: 2013 October
2014 JUKE
B2621 INSIDE ANTENNA
DLK-51
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DTC/CIRCUIT DIAGNOSIS
B2621 INSIDE ANTENNA
DTC Logic
INFOID:0000000009753946
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “INSIDE ANT DIAGNOSIS” in “WORK SUPPORT” mode.
3.
Perform inside key antenna (“INSIDE ANT DIAGNOSIS”) on “WORK SUPPORT” of “INTELLIGENT
KEY”.
4.
Check BCM for DTC.
Is inside key antenna DTC detected?
YES
>> Refer to
.
NO
>> Inside key antenna (instrument center) is OK.
Diagnosis Procedure
INFOID:0000000009753947
1.
CHECK INSIDE KEY ANTENNA INPUT SIGNAL 1
1.
Turn ignition switch ON.
2.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK INSIDE KEY ANTENNA CIRCUIT
DTC
CONSULT display
description
DTC detecting condition
Possible cause
B2621
INSIDE ANTENNA
An excessive high or low voltage from inside anten-
na (instrument center) is sent to BCM
• Inside key antenna (instrument
center)
• Harness or connector
[Inside key antenna (instrument
center) circuit is open or shorted]
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M70
84
85
Ground
When Intelligent Key is in the
antenna detection area
When Intelligent Key is not in
the antenna detection area
JMKIA3839GB
JMKIA5951GB
Revision: 2013 October
2014 JUKE
DLK-52
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2621 INSIDE ANTENNA
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and inside key antenna (instrument center) connector.
3.
Check continuity between BCM harness connector and inside key antenna (instrument center) harness
connector.
4.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK INSIDE KEY ANTENNA INPUT SIGNAL 2
1.
Replace inside key antenna (instrument center). (New antenna or other antenna)
2.
Connect BCM connector and inside key antenna (instrument center) connector.
3.
Turn ignition switch ON.
4.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace inside key antenna (instrument center).
NO
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
BCM
Inside key antenna (instrument center)
Continuity
Connector
Terminal
Connector
Terminal
M70
84
M105
1
Existed
85
2
BCM
Ground
Continuity
Connector
Terminal
M70
84
Not existed
85
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M70
84
85
Ground
When Intelligent Key is in the
antenna detection area
When Intelligent Key is not in
the antenna detection area
JMKIA3839GB
JMKIA5951GB
Revision: 2013 October
2014 JUKE
B2622 INSIDE ANTENNA
DLK-53
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
B2622 INSIDE ANTENNA
DTC Logic
INFOID:0000000009753948
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “INSIDE ANT DIAGNOSIS” in “WORK SUPPORT” mode.
3.
Perform inside key antenna (“INSIDE ANT DIAGNOSIS”) on “WORK SUPPORT” of “INTELLIGENT
KEY”.
4.
Check BCM for DTC.
Is inside key antenna DTC detected?
YES
>> Refer to
.
NO
>> Inside key antenna (console) is OK.
Diagnosis Procedure
INFOID:0000000009753949
1.
CHECK INSIDE KEY ANTENNA INPUT SIGNAL 1
1.
Turn ignition switch ON.
2.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK INSIDE KEY ANTENNA CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and inside key antenna (console) connector.
3.
Check continuity between BCM harness connector and inside key antenna (console) harness connector.
DTC
CONSULT display
description
DTC detecting condition
Possible cause
B2622
INSIDE ANTENNA
An excessive high or low voltage from inside anten-
na (console) is sent to BCM
• Inside key antenna (console)
• Harness or connector
[Inside key antenna (console) cir-
cuit is open or shorted]
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M70
86
87
Ground
When Intelligent Key is in the an-
tenna detection area
When Intelligent Key is not in the
antenna detection area
JMKIA3839GB
JMKIA5951GB
Revision: 2013 October
2014 JUKE
DLK-54
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2622 INSIDE ANTENNA
4.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK INSIDE KEY ANTENNA INPUT SIGNAL 2
1.
Replace inside key antenna (console). (New antenna or other antenna)
2.
Connect BCM connector and inside key antenna (console) connector.
3.
Turn ignition switch ON.
4.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace inside key antenna (console).
NO
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
BCM
Inside key antenna (console)
Continuity
Connector
Terminal
Connector
Terminal
M70
86
M106
1
Existed
87
2
BCM
Ground
Continuity
Connector
Terminal
M70
86
Not existed
87
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M70
86
87
Ground
When Intelligent Key is in the an-
tenna detection area
When Intelligent Key is not in the
antenna detection area
JMKIA3839GB
JMKIA5951GB
Revision: 2013 October
2014 JUKE
B2623 INSIDE ANTENNA
DLK-55
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
B2623 INSIDE ANTENNA
DTC Logic
INFOID:0000000009753950
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “INSIDE ANT DIAGNOSIS” in “WORK SUPPORT” mode.
3.
Perform inside key antenna (“INSIDE ANT DIAGNOSIS”) on “WORK SUPPORT” of “INTELLIGENT
KEY”.
4.
Check BCM for DTC.
Is inside key antenna DTC detected?
YES
>> Refer to
.
NO
>> Inside key antenna (luggage room) is OK.
Diagnosis Procedure
INFOID:0000000009753951
1.
CHECK INSIDE KEY ANTENNA INPUT SIGNAL 1
1.
Turn ignition switch ON.
2.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
NO
>> GO TO 2.
2.
CHECK INSIDE KEY ANTENNA CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and inside key antenna (luggage room) connector.
DTC
CONSULT display
description
DTC detecting condition
Possible cause
B2623
INSIDE ANTENNA
An excessive high or low voltage from inside anten-
na (luggage room) is sent to BCM
• Inside key antenna (luggage room)
• Harness or connector
[Inside key antenna (luggage
room) circuit is open or shorted]
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M70
88
89
Ground
When Intelligent Key is in the an-
tenna detection area
When Intelligent Key is not in the
antenna detection area
JMKIA3839GB
JMKIA5951GB
Revision: 2013 October
2014 JUKE
DLK-56
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2623 INSIDE ANTENNA
3.
Check continuity between BCM harness connector and inside key antenna (luggage room) harness con-
nector.
4.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK INSIDE KEY ANTENNA INPUT SIGNAL 2
1.
Replace inside key antenna (luggage room). (New antenna or other antenna)
2.
Connect BCM connector and inside key antenna (luggage room) connector.
3.
Turn ignition switch ON.
4.
Check signal between BCM harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> Replace inside key antenna (luggage room).
NO
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
BCM
Inside key antenna (luggage room)
Continuity
Connector
Terminal
Connector
Terminal
M70
88
B82
1
Existed
89
2
BCM
Ground
Continuity
Connector
Terminal
M70
88
Not existed
89
(+)
(–)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M70
88
89
Ground
When Intelligent Key is in the an-
tenna detection area
When Intelligent Key is not in the
antenna detection area
JMKIA3839GB
JMKIA5951GB
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст