Nissan Juke (2014 year). Service Repair Manual — part 49
PRECAUTIONS
DLK-9
< PRECAUTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009753917
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution for Procedure without Cowl Top Cover
INFOID:0000000009753918
When performing the procedure after removing cowl top cover, cover
the lower end of windshield with urethane, etc to prevent damage to
windshield.
PIIB3706J
Revision: 2013 October
2014 JUKE
DLK-10
< PRECAUTION >
[WITH INTELLIGENT KEY SYSTEM]
PRECAUTIONS
Precautions for Removing of Battery Terminal
INFOID:0000000010288671
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
Work
INFOID:0000000009753919
• After removing and installing the opening/closing parts, be sure to carry out fitting adjustments to check their
operational.
• Check the lubrication level, damage, and wear of each part. If necessary, grease or replace it.
SEF289H
Revision: 2013 October
2014 JUKE
PREPARATION
DLK-11
< PREPARATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009753920
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tools
INFOID:0000000009753921
Tool number
(Kent-Moore No.)
Tool name
Description
(J-39570)
Chassis ear
Locates the noise
(J-50397)
NISSAN Squeak and Rat-
tle Kit
Repairs the cause of noise
SIIA0993E
SIIA0994E
Tool name
Description
Engine ear
Locates the noise
Remover tool
Removes the clips, pawls, and metal clips
Power tool
SIIA0995E
JMKIA3050ZZ
PIIB1407E
Revision: 2013 October
2014 JUKE
DLK-12
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
COMPONENT PARTS
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000009753922
JMKIA6158ZZ
Revision: 2013 October
2014 JUKE
COMPONENT PARTS
DLK-13
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Component Description
INFOID:0000000009753923
1.
Intelligent Key warning buzzer
2.
Remote keyless entry receiver
3.
Inside key antenna (instrument cen-
ter)
4.
TCM
Refer to
SYSTEM : Component Parts Location"
5.
Push-button ignition switch
6.
Combination meter
7.
BCM
Refer to
SYSTEM : Component Parts Location"
8.
Power window main switch
9.
Outside key antenna (driver side)
10. Front door switch (driver side)
11.
Front door lock assembly (driver side) 12. Front door request switch (driver side)
13. Inside key antenna (console)
14. Inside key antenna (luggage room)
15. Back door request switch
16. Back door lock assembly
17. Outside antenna (rear bumper)
18. Front door request switch (passenger
side)
19. Outside key antenna (passenger side) 20. IPDM E/R
A.
View with front bumper removed
B.
View with instrument panel assembly
removed
C.
View with multi display unit removed
D.
View with center console assembly re-
moved
E.
View with luggage room finisher re-
moved
F.
View with rear bumper removed
Item
Function
BCM
Controls the door lock system.
Back door opener actuator
Opens the back door with the back door open signal from BCM.
Back door opener switch
Inputs back door opener switch operation signal to BCM.
Combination meter
• Displays each operation method guide and warning for system malfunction.
• Performs operation method guide and warning with buzzer.
• Transmits vehicle seep signal to CAN communication line.
Door lock actuator
• Inputs locks/unlocks signal from BCM and locks/unlocks each door.
• Integrated in each door lock assembly.
Door lock and unlock switch
• Transmits door lock/unlock operation to BCM.
• Integrated in the power window main switch and front power window switch (passenger side).
Door request switch
• Transmits door lock/unlock operation to BCM.
• Integrated in the outside handle (driver side, passenger side and back door).
Door switch
Detects door open/close condition.
Inside key antenna
• Detects whether Intelligent Key is inside the vehicle.
• Installed in the instrument center and luggage room.
Intelligent Key
The following functions are available when having and carrying electronic ID.
• Door lock/unlock
• Engine start
• Remote control entry function is available when operating on button.
Intelligent Key warning buzzer
Warns for an inappropriate operation.
IPDM E/R
Sounds horn via CAN communication between BCM.
Outside key antenna
• Detects whether Intelligent Key is outside the vehicle.
• Integrated in the outside handle (driver side, passenger side and back door).
Push-button ignition switch
• BCM transmits the change in the power supply position with the push-button ignition switch to
IPDM E/R via CAN communication line. IPDM E/R transmits the power supply position status
via CAN communication line to BCM.
• Immobilizer antenna amp checks Intelligent Key transponder.
Remote keyless entry receiver
Receives Intelligent Key operation and transmits to BCM.
TCM
Transmits shift position signal to BCM via CAN communication line
Revision: 2013 October
2014 JUKE
DLK-14
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
SYSTEM (POWER DOOR LOCK SYSTEM)
SYSTEM (POWER DOOR LOCK SYSTEM)
System Diagram
INFOID:0000000009753924
System Description
INFOID:0000000009753925
DOOR LOCK FUNCTION
Door Lock and Unlock Switch
• The door lock and unlock switch (driver side) is build into power window main switch.
• Interlocked with the locking operation of door lock and unlock switch, door lock actuators of all doors are
locked.
• Interlocked with the unlocking operation of door lock and unlock switch, door lock actuators of all doors actu-
ator are unlocked.
Door Key Cylinder Switch
• With the mechanical key inserted in the door key cylinder on driver side, turning it to lock position, locks door
lock actuator of all doors.
• With the mechanical key inserted in the door key cylinder on driver side, turning it to unlock position once
unlocks the driver side door, turning it to unlock position again within 5 seconds after the first unlock opera-
tion unlocks all of the other doors actuator. (SELECTIVE UNLOCK OPERATION)
Selective unlock operation mode can be changed using CONSULT.
Refer to
DLK-29, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
IGNITION POSITION WARNING FUNCTION
When door lock and unlock switch are operated while driver side door is open and ignition position is ACC or
ON, door locks once but immediately unlocks.
INTERIOR ROOM LAMP CONTROL FUNCTION
Interior room lamp is controlled according to door lock /unlock state, refer to
CONTROL SYSTEM : System Description"
AUTOMATIC DOOR LOCK/UNLOCK FUNCTION (LOCK OPERATION)
The interlock door lock function is the function that locks all doors linked with the vehicle speed or shift posi-
tion. It has 2 types as per the following items.
Vehicle Speed Sensing Auto Door Lock
All doors are locked when the vehicle speed reaches 24 km/h (15 MPH) or more.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is turned ON, all
doors are closed and the vehicle speed received from the combination meter via CAN communication
becomes 24 km/h (15 MPH) or more.
P Range Interlock Door Lock*
All doors are locked when shifting the selector lever from the P position to any position other than P.
BCM outputs the lock signal to all door lock actuators when it detects that the ignition switch is in the ON posi-
tion and the shift signal received from the TCM via CAN communication is shifted from the P position to any
position other than P.
JMKIA6117GB
Revision: 2013 October
2014 JUKE
SYSTEM (POWER DOOR LOCK SYSTEM)
DLK-15
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Setting change of Automatic Door Lock/Unlock Function
The lock operation setting of the automatic door lock/unlock function can be changed.
NOTE:
P range interlock door lock can be selected for M/T models, but automatic door lock/unlock function does not
operate.
With CONSULT
The ON/OFF switching of the automatic door lock function and the type selection of the automatic door lock/
unlock function can be performed at the WORK SUPPORT setting of CONSULT.
Without CONSULT
The automatic door lock function ON/OFF can be switched by performing the following operation.
1.
Close all doors (door switch OFF)
2.
Ignition switch: OFF
→
ON
3.
Press and hold the door lock and unlock switch for 5 seconds or more in the lock direction within 20 sec-
onds after turning the ignition switch ON.
4.
The switching complete when the hazard lamp blinks.
*: This function does not operate on M/T models.
AUTOMATIC DOOR LOCK/UNLOCK FUNCTION (UNLOCK OPERATION)
The automatic door lock/unlock function is the function that unlocks all doors linked with the key position or
shift position. It has 2 types as per the following items.
IGN OFF Interlock Door Unlock*
1
All doors are unlocked when the power supply position is changed from ON to OFF.
BCM outputs the unlock signal to all door lock actuators when it detects that the power supply position is
changed from ignition switch ON to OFF.
P Range Interlock Door Unlock*
2
All doors are unlocked when shifting the selector lever from any position other than the P to P position.
BCM outputs the unlock signal to all door lock actuators when it detects that the ignition switch is in the ON
position and the shift signal received from TCM via CAN communication is shifted from any position other than
the P to P position.
Setting change of Automatic Door Lock/Unlock Function
The unlock operation setting of the automatic door lock/unlock function can be changed.
NOTE:
P range interlock door lock can be selected for M/T models, but automatic door lock/unlock function does not
operate.
With CONSULT
The ON/OFF switching of the automatic door lock/unlock function and the type selection of the automatic door
lock/unlock function can be performed at the WORK SUPPORT setting of CONSULT. Refer to
"DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
Without CONSULT
The automatic door lock/unlock function ON/OFF can be switched by performing the following operation.
1.
Close all doors below (door switch OFF)
2.
Ignition switch: OFF
→
ON
3.
Press and hold the door lock and unlock switch for 5 seconds or more in the unlock direction within 20
seconds after turning the power supply position ON.
4.
The switching is complete when the hazard lamp blinks.
*
1
: This function is set to ON before delivery.
*
2
: This function does not operate on M/T models.
OFF
→
ON
: 2 blinks
ON
→
OFF
: 1 blink
OFF
→
ON
: 2 blinks
ON
→
OFF
: 1 blink
Revision: 2013 October
2014 JUKE
DLK-16
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
SYSTEM (INTELLIGENT KEY SYSTEM)
SYSTEM (INTELLIGENT KEY SYSTEM)
INTELLIGENT KEY SYSTEM
INTELLIGENT KEY SYSTEM : System Diagram
INFOID:0000000009753926
INTELLIGENT KEY SYSTEM : System Description
INFOID:0000000009753927
• The Intelligent Key system is a system that makes it possible to lock and unlock the door locks (door lock/
unlock function) by carrying the Intelligent Key, which operates based on the results of electronic ID verifica-
tion using two-way communication between the Intelligent Key and the vehicle (BCM).
CAUTION:
The driver should always carry the Intelligent Key
• The settings for each function can be changed with CONSULT.
• If an Intelligent Key is lost, a new Intelligent Key can be registered. A maximum of 4 Intelligent Keys can be
registered.
• It is possible to perform a diagnosis on the system and register an Intelligent Key with CONSULT.
JMKIA6118GB
Function
Description
Refer
Door lock
Lock/unlock can be performed by pressing the request switch
Remote keyless entry
Lock/unlock can be performed by pressing the remote controller button of the In-
telligent Key
Key reminder
The key reminder buzzer sounds a warning if the door is locked with the key left
inside the vehicle
Revision: 2013 October
2014 JUKE
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-17
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR LOCK FUNCTION
DOOR LOCK FUNCTION : System Diagram
INFOID:0000000009753928
DOOR LOCK FUNCTION : System Description
INFOID:0000000009753929
When pressing the door request switch, it is possible to lock and unlock the door by carrying the Intelligent
Key.
OPERATION DESCRIPTION
• When the BCM detects that each door request switch is pressed, it activates the outside key antenna and
inside key antenna corresponding to the pressed door request switch and transmits the request signal to the
Intelligent Key. And then, check that the Intelligent Key is near the door.
• If the Intelligent Key is within the outside key antenna detection area, it receives the request signal and
transmits the key ID signal to the BCM via remote keyless entry receiver.
• BCM receives the key ID signal and compares it with the registered key ID.
• BCM transmits door lock/unlock signal and operates each door lock actuator. At the same time, BCM blinks
hazard warning lamp (lock: 2 times, unlock: 1 time) and sounds Intelligent Key buzzer (lock: 2 times, unlock:
1 time) as a reminder.
OPERATION CONDITION
If the following conditions are satisfied, door lock/unlock operation is performed if the door request switch is
operated.
Warning
If an action that does not meet the operating condition of the Intelligent Key sys-
tem is taken, the buzzer sounds to inform the driver
Engine start
The engine can be turned on while carrying the Intelligent Key
Interior room lamp control
Interior room lamp is controlled according to door lock/unlock state
Panic alarm
When Intelligent Key panic alarm button is pressed, horn sounds
Function
Description
Refer
JMKIA6137GB
Revision: 2013 October
2014 JUKE
DLK-18
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
SYSTEM (INTELLIGENT KEY SYSTEM)
*: Even with a registered Intelligent Key remaining inside the vehicle, door locks can be unlocked from outside of the vehicle with a spare
Intelligent Key as long as key IDs are different.
OUTSIDE KEY ANTENNA DETECTION AREA
The outside key antenna detection area of door lock/unlock function
is in the range of approximately 80 cm (31.50 in) surrounding the
driver, passenger door handles (1) and back door handle (2). How-
ever, this operating range depends on the ambient conditions.
SELECTIVE UNLOCK FUNCTION
Lock Operation
When an LOCK signal is sent from door request switch (driver side, passenger side or back door), all doors
are locked.
Unlock Operation
• When an UNLOCK signal from front door request switch (driver side) is transmitted, driver side door
unlocks. When another UNLOCK signal is transmitted within 60 seconds, all door unlocks.
• When an UNLOCK signal from front door request switch (passenger side) is transmitted, passenger side
door unlocks. When another UNLOCK signal is transmitted within 60 seconds, all door unlocks.
• When an UNLOCK signal from back door request switch is transmitted, back door unlocks. When another
UNLOCK signal is transmitted within 60 seconds, all door unlocks.
How to Change Selective Unlock Operation Mode
Selective unlock operation mode can be changed using CONSULT.
Refer to
DLK-31, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
HAZARD AND BUZZER REMINDER FUNCTION
During lock, unlock, operation by each request switch, the hazard warning lamps and Intelligent Key warning
buzzer will blink or honk as a reminder.
When doors are locked, unlocked by each request switch, BCM honks Intelligent Key warning buzzer as a
reminder and blinks.
Operating Function of Hazard and Buzzer Reminder
Hazard and buzzer reminder does not operate if ignition switch ON position.
How to Change Hazard and Buzzer Reminder Operation Mode
Hazard and buzzer reminder operation mode can be changed using CONSULT.
Refer to
DLK-31, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
AUTO DOOR LOCK FUNCTION
Each door request switch operation
Operation condition
Lock
• All doors are closed
• Panic alarm is not activated
• P position warning is not activated
• Intelligent Key is outside the vehicle
• Intelligent Key is within outside key antenna detection area
Unlock
• All doors are closed
• Panic alarm is not activated
• Intelligent Key is outside the vehicle
• Intelligent Key is within outside key antenna detection area *
JMKIA5569ZZ
Operation
Hazard warning lamp blinks
Intelligent Key warning buzzer honk
Unlock
Once
Once
Lock
Twice
Twice
Revision: 2013 October
2014 JUKE
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-19
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
After door is unlocked by door request switch operation and if 60 seconds or more passes without performing
the following operation, all doors are automatically locked. However, operation check function does not acti-
vate.
How To Change Auto Door Lock Operation Mode
Auto door lock operation mode can be changed using CONSULT.
Refer to
DLK-31, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
LIST OF OPERATION RELATED PARTS
Parts marked with
×
are the parts related to operation.
BACK DOOR OPEN FUNCTION
BACK DOOR OPEN FUNCTION : System Diagram
INFOID:0000000009753930
BACK DOOR OPEN FUNCTION : System Description
INFOID:0000000009753931
While back door open in the permitted state, back door opens when back door opener switch is pressed after
back door opener request switch is operated.
BACK DOOR OPEN
Operating condition
• Door switch is ON (door is open)
• Door is locked
• Push switch is pressed
Door lock function
In
tel
lig
en
t Ke
y
Re
mo
te
ke
yl
es
s en
try rec
e
ive
r
Do
or swi
tch
Doo
r re
qu
es
t s
w
itc
h
Do
or l
o
c
k ac
tu
at
o
r
In
si
de
ke
y
an
ten
na
Out
s
id
e ke
y ant
en
na
Int
e
llig
en
t Ke
y
wa
rni
n
g
bu
zze
r
CAN co
mm
un
ic
at
io
n
s
ys
tem
BCM
Hazard warning
lamp
Pu
sh
-bu
tto
n i
g
n
iti
on
swi
tch
Co
mb
in
at
io
n
met
e
r
Door lock/unlock function
×
×
×
×
×
×
×
×
Hazard and buzzer reminder function
×
×
×
×
×
Selective unlock function
×
×
×
×
×
×
Auto door lock function
×
×
×
×
JMKIA6136GB
Revision: 2013 October
2014 JUKE
DLK-20
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
SYSTEM (INTELLIGENT KEY SYSTEM)
• When the BCM detects that back door opener switch is pressed, it starts the outside key antenna (rear
bumper) and inside key antenna and transmits the request signal to the Intelligent Key. Then, check that the
Intelligent Key is near the back door.
• If the Intelligent Key is within the outside key antenna detection area, it receives the request signal and
transmits the key ID signal to the BCM via remote keyless entry receiver.
• BCM receives the key ID signal and compares it with the registered key ID.
• BCM opens back door, simultaneously unlocks all doors.
NOTE:
In selective unlock mode, only back door opens. All doors do not unlock.
OPERATION CONDITION
If the following conditions are satisfied, the back door can be opened.
OUTSIDE KEY ANTENNA DETECTION AREA
The outside key antenna detection area of back door open function
is in the range of approximately 80 cm (31.50 in) surrounding the
back door opener switch (1). However, this operating range depends
on the ambient conditions.
LIST OF OPERATION RELATED PARTS
Parts marked with
×
are the parts related to operation.
REMOTE KEYLESS ENTRY FUNCTION
Back door open function
Operation condition
Back door open operation
• Vehicle speed is less than 5 km/h (3 MPH)
• 3 seconds or more after BCM outputs all doors lock signal
• Intelligent Key is outside of vehicle
• Intelligent Key is within outside key antenna detection area
JMKIA5804ZZ
Door lock function
In
te
lli
ge
nt Key
Re
mo
te ke
yl
es
s ent
ry rec
e
iv
er
Ba
c
k
d
o
o
r op
en
er
ac
tua
to
r
Do
or l
o
c
k
ac
tua
to
r
In
si
d
e
ke
y a
n
ten
n
a
Ou
ts
id
e
k
e
y
an
te
nna
CAN co
mm
un
ic
ati
o
n
sy
s
tem
BCM
Ba
c
k
d
o
o
r op
en
er
swit
ch
Co
mb
in
ati
o
n
me
te
r
Back door open function
×
×
×
×
×
×
×
×
×
×
Revision: 2013 October
2014 JUKE
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-21
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY FUNCTION : System Diagram
INFOID:0000000009753932
REMOTE KEYLESS ENTRY FUNCTION : System Description
INFOID:0000000009753933
The Intelligent Key has the same functions as the remote control entry system. Therefore, it can be used in the
same manner as the remote controller by operating the door lock/unlock button.
OPERATION
Remote keyless entry system controls operation of the following items.
• Door lock/unlock
• Selective unlock function
• Hazard reminder function
• Auto door lock
OPERATION AREA
To check that the Intelligent Key works normally, use within 1 m (3 ft) range of each doors, however the opera-
ble range may differ according to surroundings.
DOOR LOCK/UNLOCK FUNCTION
• When door lock/unlock button of the Intelligent Key is pressed, lock signal or unlock signal transmitted from
Intelligent Key to BCM via remote keyless entry receiver.
• BCM receives the signal and compares it with the registered key ID to the vehicle.
• When BCM receives the door lock/unlock signal, it operates all door lock actuators and the hazard lamp
(lock: 2 times, unlock: 1 time) and horn chirp signal to IPDM E/R at the same time as a reminder.
• IPDM E/R honks horn (lock: 1 times) as a reminder
OPERATION CONDITION
If the following condition are satisfied, remote keyless entry operation is performed when the Intelligent Key is
operated.
SELECTIVE UNLOCK FUNCTION
• When an LOCK signal is transmitted from Intelligent Key, all doors are locked.
• When an UNLOCK signal is transmitted from Intelligent Key once, driver side door is unlocked.
• Then, if an UNLOCK signal is transmitted from Intelligent Key again within 60 seconds, all other doors are
unlocked.
How To Change Selective Unlock Operation Mode
Selective unlock operation mode can be changed using CONSULT.
JMKIA6159GB
Remote controller operation
Operation condition
Lock
• Panic alarm is not activated
• P position warning is not activated
Unlock
Panic alarm is not activated
Revision: 2013 October
2014 JUKE
DLK-22
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-29, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
.
HAZARD AND HORN REMINDER FUNCTION
When doors are locked or unlocked by Intelligent Key, BCM blinks hazard warning lamps as a reminder and
transmits horn chirp signal to IPDM E/R. IPDM E/R sounds horn as a reminder.
The hazard and horn reminder has a horn chirp mode (C mode) and a non-horn chirp mode (S mode).
Operating Function of Hazard and Horn Reminder
Hazard and horn reminder does not operate if ignition switch ON position.
How to change hazard and horn reminder mode
With CONSULT
DLK-31, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
Without CONSULT
When LOCK and UNLOCK signals are sent from the Intelligent Key for more than 2 seconds at the same time,
the hazard and horn reminder mode is changed and hazard warning lamp blinks and horn sounds as per the
following items:
AUTO DOOR LOCK FUNCTION
After door is unlocked by Intelligent Key button operation and if 60 seconds or more passes without performing
the following operation, all doors are locked. However, operation check function does not activate.
How To Change Auto Door Lock Operation Mode
Auto door lock operation mode can be changed using CONSULT.
Refer to
DLK-31, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
LIST OF OPERATION RELATED PARTS
Parts marked with
×
are the parts related to operation.
C mode
S mode
Intelligent Key operation
Lock
Unlock
Back door
open
Lock
Unlock
Back door
open
Hazard warning lamp blinks
Twice
Once
—
Twice
—
—
Horn sound
Once
—
—
—
—
—
JMKIA6362GB
Operating condition
• Door switch is ON (door is open)
• Door is locked
• Push switch is pressed
Revision: 2013 October
2014 JUKE
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-23
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEY REMINDER FUNCTION
KEY REMINDER FUNCTION : System Diagram
INFOID:0000000009753934
KEY REMINDER FUNCTION : System Description
INFOID:0000000009753935
Key reminder is the function that prevents the key from being left in the vehicle.
Key reminder has the following 3 functions.
Remote keyless entry functions
Int
e
llig
en
t Ke
y
Doo
r swi
tch
Do
or l
o
c
k
ac
tua
to
r
Pu
sh
-bu
tto
n i
g
n
iti
on
swi
tch
Inte
llige
n
t Ke
y wa
rni
ng
bu
zz
er
CAN c
o
m
m
un
ica
ti
o
n sy
st
em
BCM
Co
mb
in
at
ion
me
te
r
Hazard warning lamp
Horn
IP
DM E/
R
Door lock/unlock function
×
×
×
×
×
Hazard and horn reminder function
×
×
×
×
×
×
×
×
Selective unlock function
×
×
×
×
×
Auto door lock function
×
×
×
×
×
JMKIA5390GB
Key remainder func-
tion
Operation condition
Operation
Driver side door
closed*
Right after driver side door is closed under the following conditions
• Intelligent Key is inside the vehicle
• Driver side door is opened
• Driver side door is in unlock state
All doors unlock
Door is open to closed
Right after all doors are closed under the following conditions
• Intelligent Key is inside the vehicle
• Any door is opened
• All doors are locked.
• All doors unlock
• Honk Intelligent Key warn-
ing buzzer
Back door is closed
Right after back door is closed under the following conditions
• Intelligent Key is inside the vehicle
• All doors (except back door) are closed
• All doors (except back door) are locked
• All doors unlock
• Back door can open with
back door opener switch
• Honk Intelligent Key warn-
ing buzzer
Revision: 2013 October
2014 JUKE
DLK-24
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
SYSTEM (INTELLIGENT KEY SYSTEM)
*:If the door closing impact shocks the door lock knob, or contacts against baggage with the door lock knob might activate the door locks
accidentally but unlock operation is perform in these cases.
CAUTION:
• The above function operates when the Intelligent Key is inside the vehicle. However, there may be
times when the Intelligent Key cannot be detected, and this function does not operate when the Intel-
ligent Key is on the instrument panel, rear parcel shelf, or in the glove box. Also, this system some-
times does not operate if the Intelligent Key is in the door pocket for the open door.
WARNING FUNCTION
WARNING FUNCTION : System Description
INFOID:0000000009753936
OPERATION DESCRIPTION
The warning function are as per the following items and are given to the user as warning information and
warnings using combinations of Intelligent Key warning buzzer, combination meter buzzer, KEY warning lamp,
shift P warning lamp and engine start operation indicator lamp.
• Intelligent Key system malfunction
• OFF position warning
• P position warning
• ACC warning
• Take away warning
• Door lock operation warning
• Engine start information
• Intelligent Key low battery warning
• Key ID warning
OPERATION CONDITION
Operation condition of warning and information is as per the following table.
Warning/Information functions
Operation procedure
Intelligent Key system malfunction
A malfunction is detected on BCM and key warning lamp turns ON
OFF position warning
For internal
When condition A, B or condition C is satisfied
• Condition A
- Ignition switch: ACC position
- Door switch (driver side): ON (Door is open)
• Condition B
- Turn ignition switch from ON to OFF while door is open
• Condition C
- Intelligent Key backside is contacted to ignition switch while brake pedal is de-
pressed and ignition switch is LOCK or OFF (When the Intelligent Key battery
is discharged)
- Door switch (driver side): ON (Door is open)
For external*
OFF position warning (For internal) is in active mode, driver side door is closed
NOTE:
OFF position warning (for external) operates only when driver door is closed af-
ter each of P position warning, ACC warning, and OFF position warning (inter-
nal) sounds.
P position warning*
For internal
• Shift position: Except P position
• Engine is running to stopped (Ignition switch is ON to OFF)
For external
• P position warning (For internal) operates
• Door switch: ON to OFF (Door is open to close)
• Intelligent Key cannot be detected inside the vehicle
ACC warning*
• After P position warning operates, or when ignition switch is turned ON imme-
diately after P position warning operates
• Ignition switch: ACC position
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст