Nissan Juke (2014 year). Service Repair Manual — part 47
DEF-26
< DTC/CIRCUIT DIAGNOSIS >
REAR WINDOW DEFOGGER SWITCH
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace A/C control. Refer to
HAC-142, "Removal and Installation"
.
A/C control
Condition
Continuity
Terminal
3
8
Rear window defogger switch
Pressed
Existed
Released
Not existed
Revision: 2013 October
2014 JUKE
REAR WINDOW DEFOGGER RELAY
DEF-27
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
REAR WINDOW DEFOGGER RELAY
Description
INFOID:0000000009754260
The rear window defogger is operated by turning the rear window defogger switch ON.
Component Function Check
INFOID:0000000009754261
1.
CHECK FUNCTION
1.
Perform IPDM E/R Active Test (“REAR DEFOGGER”) using CONSULT.
2.
Touch “ON”.
3.
Check that the rear window heating wire is getting warmer.
Is the inspection result normal?
YES
>> Rear window defogger relay function is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009754262
1.
CHECK FUSE
1.
Turn ignition switch OFF.
2.
Check the 15A fuse (No. 41 and 42 located in IPDM E/R).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
2.
CHECK IPDM E/R OUTPUT SIGNAL
1.
Perform IPDM E/R Active Test (“REAR DEFOGGER”) using CONSULT.
2.
Touch “ON”.
3.
Check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace IPDM E/R. Refer to
PCS-34, "Removal and Installation"
(With Intelligent Key system) or
PCS-62, "Removal and Installation"
(Without Intelligent Key system).
(+)
(
−
)
CONSULT Active Test condition
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E11
14
Ground
REAR DEFOGGER
ON
Battery voltage
OFF
0
Revision: 2013 October
2014 JUKE
DEF-28
< DTC/CIRCUIT DIAGNOSIS >
REAR WINDOW DEFOGGER
REAR WINDOW DEFOGGER
Description
INFOID:0000000009754263
Heats the heating wire with the power supply from the rear window defogger relay to prevent the rear window
from fogging up.
Component Function Check
INFOID:0000000009754264
1.
CHECK FUNCTION
1.
Perform IPDM E/R Active Test (“REAR DEFOGGER”) using CONSULT.
2.
Touch “ON”.
3.
Check that the rear window heating wire is getting warmer.
Is the inspection result normal?
YES
>> Rear window defogger is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009754265
1.
CHECK REAR WINDOW DEFOGGER POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect rear window defogger connector.
3.
Turn ignition switch ON.
4.
Check voltage between rear window defogger harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> GO TO 4.
2.
CHECK REAR WINDOW DEFOGGER GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between rear window defogger harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK FILAMENT
DEF-47, "Inspection and Repair"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair filament.
4.
CHECK REAR WINDOW DEFOGGER POWER SUPPLY CIRCUIT 1
1.
Turn ignition switch OFF.
2.
Disconnect condenser connector.
3.
Check continuity between condenser harness connector and rear window defogger harness connector.
(+)
(
−
)
Condition
Voltage (V)
(Approx.)
Rear window defogger
Connector
Terminal
D202
1
Ground
Rear window defogger switch
ON
Battery voltage
OFF
0
Rear window defogger
Ground
Continuity
Connector
Terminal
D203
2
Existed
Revision: 2013 October
2014 JUKE
REAR WINDOW DEFOGGER
DEF-29
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
4.
Check continuity between condenser connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK REAR WINDOW DEFOGGER POWER SUPPLY CIRCUIT 2
1.
Disconnect IPDM E/R connectors.
2.
Check continuity between IPDM E/R harness connector and condenser harness connector.
3.
Check continuity between IPDM E/R connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK CONDENSER
DEF-29, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace condenser. Refer to
DEF-49, "Removal and Installation"
.
7.
CHECK INTERMITTENT INCIDENT
GI-46, "Intermittent Incident"
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Repair or replace harness or connector.
Component Inspection
INFOID:0000000009754266
1.
CHECK CONDENSER
1.
Turn ignition switch OFF.
2.
Disconnect condenser connector.
3.
Check continuity between condenser connector and ground part of condenser.
4.
Check continuity between condenser terminals.
Condenser
Rear window defogger
Continuity
Connector
Terminal
Connector
Terminal
D201
2
D202
1
Existed
Condenser
Ground
Continuity
Connector
Terminal
D201
2
Not existed
IPDM E/R
Condenser
Continuity
Connector
Terminal
Connector Terminal
E11
14
D103
1
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E11
14
Not existed
Condenser
Ground part of
condenser
Continuity
Connector
Terminal
D103
1
Not existed
D202
2
Revision: 2013 October
2014 JUKE
DEF-30
< DTC/CIRCUIT DIAGNOSIS >
REAR WINDOW DEFOGGER
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace condenser. Refer to
DEF-49, "Removal and Installation"
.
Condenser
Continuity
Connector
Terminal
Connector
Terminal
D103
1
D202
2
Existed
Revision: 2013 October
2014 JUKE
DOOR MIRROR DEFOGGER
DEF-31
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
DOOR MIRROR DEFOGGER
Description
INFOID:0000000009754267
Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror
from fogging up.
Component Function Check
INFOID:0000000009754268
1.
CHECK DOOR MIRROR DEFOGGER
1.
Perform IPDM E/R Active Test (“REAR DEFOGGER”) using CONSULT.
2.
Touch “ON”.
3.
Check that both side door mirror glasses are getting warmer.
Is the inspection result normal?
YES
>> Door mirror defogger is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009754269
1.
CHECK FUSE
1.
Turn ignition switch OFF.
2.
Check 10A fuse [No.22, located in fuse block (J/B)].
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.
2.
CHECK DOOR MIRROR DEFOGGER CIRCUIT
1.
Disconnect IPDM E/R connector and door mirror (both sides) connector.
2.
Check continuity between IPDM E/R harness connector and door mirror (driver side) harness connector.
3.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK INTERMITTENT INCIDENT
Check intermittent incident.
Refer to
GI-46, "Intermittent Incident"
.
>> INSPECTION END
IPDM E/R
Door mirror (driver side)
Continuity
Connector
Terminal
Connector
Terminal
E11
14
D29
3
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E11
14
Not existed
Revision: 2013 October
2014 JUKE
DEF-32
< DTC/CIRCUIT DIAGNOSIS >
DRIVER SIDE DOOR MIRROR DEFOGGER
DRIVER SIDE DOOR MIRROR DEFOGGER
Description
INFOID:0000000009754270
Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror
from fogging up.
Component Function Check
INFOID:0000000009754271
1.
CHECK DRIVER SIDE DOOR MIRROR DEFOGGER
1.
Perform IPDM E/R Active Test (“REAR DEFOGGER”) using CONSULT.
2.
Touch “ON”.
3.
Check that the driver side door mirror glass is getting warmer.
Is the inspection result normal?
YES
>> Driver side door mirror defogger is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009754272
1.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect door mirror (driver side) connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace door mirror glass (driver side). Refer to
MIR-17, "DOOR MIRROR ASSEMBLY : Removal
.
NO
>> Repair or replace harness.
(+)
(–)
Condition
Voltage (V)
(Approx.)
Door mirror (driver side)
Connector
Terminal
D29
3
Ground
Rear window defogger
switch
ON
Battery voltage
OFF
0
Door mirror (driver side)
Ground
Continuity
Connector
Terminal
D29
2
Existed
Revision: 2013 October
2014 JUKE
PASSENGER SIDE DOOR MIRROR DEFOGGER
DEF-33
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
PASSENGER SIDE DOOR MIRROR DEFOGGER
Description
INFOID:0000000009754273
Heats the heating wire with the power supply from the rear window defogger relay to prevent the door mirror
from fogging up.
Component Function Check
INFOID:0000000009754274
1.
CHECK PASSENGER SIDE DOOR MIRROR DEFOGGER
1.
Perform IPDM E/R Active Test (“REAR DEFOGGER”) using CONSULT.
2.
Touch “ON”.
3.
Check that the passenger side door mirror glass is getting warmer.
Is the inspection result normal?
YES
>> Passenger side door mirror defogger is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009754275
1.
CHECK POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect door mirror (passenger side) connector.
3.
Turn ignition switch ON.
4.
Check voltage between door mirror (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Check continuity between door mirror (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace door mirror glass (passenger side). Refer to
MIR-17, "DOOR MIRROR ASSEMBLY :
.
NO
>> Repair or replace harness.
(+)
(–)
Condition
Voltage (V)
(Approx.)
Door mirror (passenger side)
Connector
Terminal
D8
3
Ground
Rear window defogger
switch
ON
Battery voltage
OFF
0
Door mirror (passenger side)
Ground
Continuity
Connector
Terminal
D8
2
Existed
Revision: 2013 October
2014 JUKE
DEF-34
< DTC/CIRCUIT DIAGNOSIS >
REAR WINDOW DEFOGGER FEEDBACK SIGNAL
REAR WINDOW DEFOGGER FEEDBACK SIGNAL
Description
INFOID:0000000009754276
Turns the indicator lamp in the rear window defogger switch ON when operating the rear window defogger.
Component Function Check
INFOID:0000000009754277
1.
CHECK REAR WINDOW DEFOGGER FEEDBACK SIGNAL
Check that the indicator lamp of rear window defogger switch is illuminated when turning the rear window
defogger switch ON.
Is the inspection result normal?
OK
>> Rear window defogger feedback signal is OK.
NG
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009754278
1.
CHECK REAR WINDOW DEFOGGER FEEDBACK SIGNAL
1.
Turn ignition switch ON.
2.
Check voltage between A/C control harness connector and ground.
Is the inspection result normal?
YES
>> Replace A/C control.
NO
>> Repair or replace harness.
A/C control
Ground
Condition
Voltage (V)
(Approx.)
Connector
Terminal
M53
4
Rear window defogger switch
ON
Battery voltage
OFF
0
Revision: 2013 October
2014 JUKE
REAR WINDOW DEFOGGER SYSTEM
DEF-35
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
REAR WINDOW DEFOGGER SYSTEM
Wiring Diagram - DEFOGGER CONTROL SYSTEM -
INFOID:0000000009754279
JCLWA4334GB
Revision: 2013 October
2014 JUKE
DEF-36
< DTC/CIRCUIT DIAGNOSIS >
REAR WINDOW DEFOGGER SYSTEM
JRLWD0886GB
Revision: 2013 October
2014 JUKE
REAR WINDOW DEFOGGER SYSTEM
DEF-37
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
JRLWD0887GB
Revision: 2013 October
2014 JUKE
DEF-38
< DTC/CIRCUIT DIAGNOSIS >
REAR WINDOW DEFOGGER SYSTEM
JRLWD0888GB
Revision: 2013 October
2014 JUKE
REAR WINDOW DEFOGGER SYSTEM
DEF-39
< DTC/CIRCUIT DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
JRLWD0889GB
Revision: 2013 October
2014 JUKE
DEF-40
< DTC/CIRCUIT DIAGNOSIS >
REAR WINDOW DEFOGGER SYSTEM
JRLWD0890GB
Revision: 2013 October
2014 JUKE
ALL DEFOGGER SYSTEMS DO NOT OPERATE
DEF-41
< SYMPTOM DIAGNOSIS >
C
D
E
F
G
H
I
J
K
M
A
B
DEF
N
O
P
SYMPTOM DIAGNOSIS
ALL DEFOGGER SYSTEMS DO NOT OPERATE
Description
INFOID:0000000009754280
Rear window defogger and door mirror defogger do not operate when rear window defogger switch operated.
Diagnosis Procedure
INFOID:0000000009754281
1.
CHECK REAR WINDOW DEFOGGER SWITCH
Check rear window defogger switch.
Refer to
DEF-24, "WITH AUTO A/C : Component Function Check"
(With Auto A/C) or
AUTO A/C : Component Function Check"
(Without Auto A/C).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK REAR WINDOW DEFOGGER RELAY
Check rear window defogger relay.
Refer to
DEF-27, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK REAR WINDOW DEFOGGER
Check rear window defogger.
Refer to
DEF-28, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection result normal?
YES
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
NO
>> GO TO 1.
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст