Nissan Juke (2014 year). Service Repair Manual — part 123
EX-2
< PRECAUTION >
[MR16DDT ]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precautions for Removing of Battery Terminal
INFOID:0000000010177975
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
Removal and Installation
INFOID:0000000009753637
CAUTION:
• Be sure to use genuine exhaust system parts or equivalents which are specially designed for heat
resistance, corrosion resistance, and shape.
• Perform the operation with the exhaust system fully cooled down because the system will be hot
just after engine stops.
• Be careful not to cut your hand on the heat insulator edge.
SEF289H
Revision: 2013 October
2014 JUKE
PREPARATION
EX-3
< PREPARATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
PREPARATION
PREPARATION
Special Service Tools
INFOID:0000000009753638
Commercial Service Tools
INFOID:0000000009753639
Tool number
(Kent- Mooer No.)
Tool name
Description
KV10114400
(J-38365)
Heated oxygen sensor wrench
Loosening or tightening heated oxygen sen-
sor 2 ( 2WD models)
a: For 22 mm (0.87 in) width hexagon nut
S-NT636
Tool name
Description
Power tool
Loosening nuts and bolts
Heated oxygen sensor thread cleaner
Reconditioning the exhaust system threads
before installing a new heated oxygen sensor
(Use with anti-seize lubricant shown below.)
A: J-43897-18 [18 mm (0.71 in) dia.] for zir-
conia heated oxygen sensor
B: J-43897-12 [12 mm (0.47 in) dia.] for tita-
nia heated oxygen sensor
C: Mating surface shave cylinder
D: Flutes
Anti-seize lubricant (Permatex 133AR
or equivalent meeting MIL specifica-
tion MIL-A-907)
Lubricating heated oxygen sensor thread
cleaner when reconditioning exhaust system
threads
PBIC0190E
JPBIA0238ZZ
AEM489
Revision: 2013 October
2014 JUKE
EX-4
< PERIODIC MAINTENANCE >
[MR16DDT ]
EXHAUST SYSTEM
PERIODIC MAINTENANCE
EXHAUST SYSTEM
Inspection
INFOID:0000000009753640
Check exhaust pipes, muffler, and mounting for improper attach-
ment, leakage, cracks, damage or deterioration.
• If anything is found, repair or replace damaged parts.
SMA211A
Revision: 2013 October
2014 JUKE
EXHAUST SYSTEM
EX-5
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
REMOVAL AND INSTALLATION
EXHAUST SYSTEM
Exploded View
INFOID:0000000009753641
2WD (Standard models)
JSBIA3454GB
1.
Center muffler
2.
Mounting rubber
3.
Spring
4.
Seal bearing
5.
Stud bolt
6.
Exhaust front tube
7.
Heated oxygen sensor 2
8.
Seal bearing
9.
Ring gasket
10. Main muffler
A.
To catalyst convertor
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
Revision: 2013 October
2014 JUKE
EX-6
< REMOVAL AND INSTALLATION >
[MR16DDT ]
EXHAUST SYSTEM
2WD (NISMO RS models)
JSBIA4459GB
1.
Center muffler
2.
Mounting rubber
3.
Spring
4.
Seal bearing
5.
Stud bolt
6.
Exhaust front tube
7.
Heated oxygen sensor 2
8.
Seal bearing
9.
Ring gasket
10. Main muffler
A.
To catalyst convertor
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
Revision: 2013 October
2014 JUKE
EXHAUST SYSTEM
EX-7
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
AWD (Standard models)
JSBIA3455GB
1.
Center pipe
2.
Mounting rubber
3.
Spring
4.
Seal bearing
5.
Stud bolt
6.
Exhaust front tube
7.
Seal bearing
8.
Ring gasket
9.
Main muffler
A.
To catalyst convertor
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
Revision: 2013 October
2014 JUKE
EX-8
< REMOVAL AND INSTALLATION >
[MR16DDT ]
EXHAUST SYSTEM
AWD (NISMO RS models)
Removal and Installation
INFOID:0000000009753642
REMOVAL
• Disconnect each joint and mounting.
• Remove heated oxygen sensor 2 with following procedure (2WD models):
- Using heated oxygen sensor wrench [SST: KV10114400 (J-
38365)] (A), removal heated oxygen sensor 2 (1).
CAUTION:
• Never damage heated oxygen sensor 2.
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
• Always replace seal bearings with new ones when reassembling.
JSBIA3379GB
1.
Center pipe
2.
Mounting rubber
3.
Spring
4.
Seal bearing
5.
Stud bolt
6.
Exhaust front tube
7.
Seal bearing
8.
Ring gasket
9.
Main muffler
A.
To catalyst convertor
: N·m (kg-m, ft-lb)
: Always replace after every disassembly.
PBIC4498J
Revision: 2013 October
2014 JUKE
EXHAUST SYSTEM
EX-9
< REMOVAL AND INSTALLATION >
[MR16DDT ]
C
D
E
F
G
H
I
J
K
L
M
A
EX
N
P
O
• Discard any heated oxygen sensor 2 which has been dropped onto a hard surface such as a con-
crete floor. Use a new one.
• Before installing a new heated oxygen sensor 2, clean exhaust system threads using the heated oxy-
gen sensor thread cleaner [commercial service tool: J-43897-18 or J-43897-12] and apply anti-seize
lubricant (commercial service tool).
• Never over torque heated oxygen sensor 2. Doing so may cause damage to the heated oxygen sen-
sor 2, resulting in the “MIL” coming on.
• Prevent rust preventives from adhering to the sensor body.
• If heat insulator is badly deformed, repair or replace it. If deposits such as mud pile up on the heat
insulator, remove them.
• When installing heat insulator avoid large gaps or interference between heat insulator and each
exhaust pipe.
• Remove deposits from the sealing surface of each connection. Connect them securely to avoid gas
leakage.
• When installing each mounting rubber, use silicon oil to avoid twisting.
• Temporarily tighten mounting nuts and bolts. Check each part for unusual interference and mount-
ing rubber interference, and then tighten them to the specified torque.
• When installing each mounting rubber, avoid twisting or unusual extension in up/down, front/rear
and right/left directions.
• Install seal bearing according to the following instructions.
CAUTION:
The structure of seal bearing depends on the mounting por-
tion. When installing seal bearings, be careful not to install
wrong one.
Exhaust Manifold to Exhaust Front Tube
1.
Place a piece of wood (A) on seal bearing (2) and securely
insert the seal bearing on the exhaust manifold (1) side, using a
plastic hammer (B).
CAUTION:
• Never damage the seal bearing surface during insertion.
• If seal bearing is inserted by hammering directly without
using a piece of wood, the seal bearing is deformed and
exhaust gas leaks. To insert seal bearing, always use a
piece of wood and insert straight.
: Exhaust manifold side
: Mesh
: Exhaust front tube side
: Pawl (projection)
JPBIA6287ZZ
JPBIA6288ZZ
Revision: 2013 October
2014 JUKE
EX-10
< REMOVAL AND INSTALLATION >
[MR16DDT ]
EXHAUST SYSTEM
2.
Check that seal bearing (1) is in absolute contact (C) with the
flange (A). If there is clearance (B), insert seal bearing straight
by hand to bring the seal bearing into absolute contact with the
flange.
CAUTION:
• Never use a tool for insertion.
• Never insert seal bearing by tightening exhaust front
tube.
3.
With spring (3), tighten nut (4).
CAUTION:
• Fasten stud bolts to the flange of exhaust manifold side to
the specified torque before fastening mounting nuts.
• Ensure springs are seated correctly on the flange and not
sitting on (A).
• Be careful that stud bolt does not interfere with mounting hole of exhaust front tube (
).
4.
After installing, check that stud bolt does not interfere with mounting hole of exhaust front tube.
Exhaust Front Tube to Main Muffler
1.
Securely insert seal bearing (2) into exhaust front tube (1) side
in the direction as shown in the figure.
CAUTION:
Be careful not to damage seal bearing surface when install-
ing.
2.
With spring, tighten bolt.
CAUTION:
• Ensure springs are seated correctly on the flange and not sitting on (A).
• Be careful that bolt does not interfere with mounting hole of main muffler (
).
3.
After installing, check that bolt does not interfere with mounting hole of main muffler.
Inspection
INFOID:0000000009753643
INSPECTION AFTER INSTALLATION
• Check clearance between tail tube and rear bumper is even.
• With engine running, check exhaust tube joints for gas leakage and unusual noises.
• Check to ensure that mounting brackets and mounting rubbers are installed properly and free from undue
stress. Improper installation could result in excessive noise and vibration.
JPBIA6289ZZ
1
: Exhaust manifold
2
: Seal bearing
5
: Stud bolt
6
: Exhaust front tube
JPBIA2372ZZ
3
: Spring
4
: Bolt
5
: Main muffler
JPBIA2174ZZ
Revision: 2013 October
2014 JUKE
EXL-1
DRIVER CONTROLS
C
D
E
F
G
H
I
J
K
M
SECTION
EXL
A
B
EXL
N
O
P
CONTENTS
EXTERIOR LIGHTING SYSTEM
HALOGEN TYPE
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precautions for Removing of Battery Terminal . .....
SYSTEM DESCRIPTION . . . . . . . ..
COMPONENT PARTS . . . . . . . . . .
Component Parts Location . . . . . . . . . ....
Component Description . . . . . . . . . . ....
SYSTEM . . . . . . . . . . . . . . . ..
HEADLAMP SYSTEM . . . . . . . . . . . .....
HEADLAMP SYSTEM : System Diagram . . . .....
HEADLAMP SYSTEM : System Description . . .....
HEADLAMP SYSTEM : Fail-safe . . . . . . . ..
AUTO LIGHT SYSTEM . . . . . . . . . . . ...
AUTO LIGHT SYSTEM : System Diagram . . . ...
AUTO LIGHT SYSTEM : System Description . . ...
DAYTIME RUNNING LIGHT SYSTEM . . . . . ....
DAYTIME RUNNING LIGHT SYSTEM : System
Diagram . . . . . . . . . . . . . . . . ...
DAYTIME RUNNING LIGHT SYSTEM : System
Description . . . . . . . . . . . . . . . ..
FRONT FOG LAMP SYSTEM . . . . . . . . ...
FRONT FOG LAMP SYSTEM : System Diagram .
FRONT FOG LAMP SYSTEM : System Descrip-
tion . . . . . . . . . . . . . . . . . . ..
FRONT FOG LAMP SYSTEM : Fail-safe . . . .
TURN SIGNAL AND HAZARD WARNING LAMP
SYSTEM . . . . . . . . . . . . . . . . .
TURN SIGNAL AND HAZARD WARNING LAMP
SYSTEM : System Diagram . . . . . . . . .
TURN SIGNAL AND HAZARD WARNING LAMP
SYSTEM : System Description . . . . . . . .
PARKING, LICENSE PLATE, SIDE MARKER AND
TAIL LAMP SYSTEM . . . . . . . . . . . . .
PARKING, LICENSE PLATE, SIDE MARKER
AND TAIL LAMP SYSTEM : System Diagram . .
PARKING, LICENSE PLATE, SIDE MARKER
AND TAIL LAMP SYSTEM : System Description .
PARKING, LICENSE PLATE, SIDE MARKER
AND TAIL LAMP SYSTEM : Fail-safe . . . . . .
EXTERIOR LAMP BATTERY SAVER SYSTEM . ...
EXTERIOR LAMP BATTERY SAVER SYSTEM :
System Diagram . . . . . . . . . . . . . ..
EXTERIOR LAMP BATTERY SAVER SYSTEM :
System Description . . . . . . . . . . . . ..
DIAGNOSIS SYSTEM (BCM) (WITH INTELLI-
GENT KEY SYSTEM) . . . . . . . . . ...
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
HEADLAMP . . . . . . . . . . . . . . . ...
HEADLAMP : CONSULT Function (BCM - HEAD
LAMP) . . . . . . . . . . . . . . . . . ..
FLASHER . . . . . . . . . . . . . . . . ...
FLASHER : CONSULT Function (BCM - FLASH-
ER) . . . . . . . . . . . . . . . . . . ..
DIAGNOSIS SYSTEM (BCM) (WITHOUT IN-
TELLIGENT KEY SYSTEM) . . . . . . . .
COMMON ITEM . . . . . . . . . . . . . . .
COMMON ITEM : CONSULT Function (BCM -
COMMON ITEM) . . . . . . . . . . . . . .
HEADLAMP . . . . . . . . . . . . . . . ...
HEADLAMP : CONSULT Function (BCM - HEAD
LAMP) . . . . . . . . . . . . . . . . . ..
Revision: 2013 October
2014 JUKE
EXL-2
FLASHER . . . . . . . . . . . . . . . . ..
FLASHER : CONSULT Function (BCM - FLASH-
ER) . . . . . . . . . . . . . . . . . . .
DIAGNOSIS SYSTEM (IPDM E/R) (WITH IN-
TELLIGENT KEY SYSTEM) . . . . . . . ..
Diagnosis Description . . . . . . . . . . . .
CONSULT Function (IPDM E/R) . . . . . . ....
DIAGNOSIS SYSTEM (IPDM E/R) (WITHOUT
INTELLIGENT KEY SYSTEM) . . . . . . ..
Diagnosis Description . . . . . . . . . . . .
CONSULT Function (IPDM E/R) . . . . . . ....
ECU DIAGNOSIS INFORMATION . . . ..
BCM, IPDM E/R . . . . . . . . . . . . .
List of ECU Reference . . . . . . . . . . ....
WIRING DIAGRAM . . . . . . . . . .
EXTERIOR LIGHTING SYSTEM . . . . . ...
Wiring Diagram . . . . . . . . . . . . . ...
BASIC INSPECTION . . . . . . . . ...
DIAGNOSIS AND REPAIR WORK FLOW . .
Work Flow . . . . . . . . . . . . . . . ...
DTC/CIRCUIT DIAGNOSIS . . . . . . .
HEADLAMP (HI) CIRCUIT . . . . . . . .
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ..
HEADLAMP (LO) CIRCUIT . . . . . . . ...
WITHOUT DAYTIME RUNNING LIGHT SYSTEM ...
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
: Component Function Check . . . . . . . . .
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
: Diagnosis Procedure . . . . . . . . . . ....
WITH DAYTIME RUNNING LIGHT SYSTEM . . ...
WITH DAYTIME RUNNING LIGHT SYSTEM :
Component Function Check . . . . . . . . ...
WITH DAYTIME RUNNING LIGHT SYSTEM : Di-
agnosis Procedure . . . . . . . . . . . . ..
WITH DAYTIME RUNNING LIGHT SYSTEM :
Component Inspection . . . . . . . . . . ....
HEADLAMP GROUND CIRCUIT . . . . . ..
WITHOUT DAYTIME RUNNING LIGHT SYSTEM ...
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
: Diagnosis Procedure . . . . . . . . . . ....
WITH DAYTIME RUNNING LIGHT SYSTEM . . ...
WITH DAYTIME RUNNING LIGHT SYSTEM : Di-
agnosis Procedure . . . . . . . . . . . . ..
DAYTIME RUNNING LIGHT RELAY CIRCUIT
...
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
Component Inspection . . . . . . . . . . .
DAYTIME RUNNING LIGHT CIRCUIT . . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
PARKING LAMP CIRCUIT . . . . . . . .
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
FRONT SIDE MARKER LAMP CIRCUIT . . ..
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
TAIL LAMP CIRCUIT . . . . . . . . . .
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
LICENSE PLATE LAMP CIRCUIT . . . . .
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
OPTICAL SENSOR . . . . . . . . . . ...
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
FRONT FOG LAMP CIRCUIT . . . . . . ...
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
TURN SIGNAL LAMP CIRCUIT . . . . . .
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
HAZARD SWITCH . . . . . . . . . . . .
Component Function Check . . . . . . . . ...
Diagnosis Procedure . . . . . . . . . . . ...
SYMPTOM DIAGNOSIS . . . . . . .
EXTERIOR LIGHTING SYSTEM SYMPTOMS ...
WITHOUT DAYTIME RUNNING LIGHT SYSTEM .
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
: Symptom Table . . . . . . . . . . . . . .
WITH DAYTIME RUNNING LIGHT SYSTEM . . ...
WITH DAYTIME RUNNING LIGHT SYSTEM :
Symptom Table . . . . . . . . . . . . . ...
NORMAL OPERATING CONDITION . . . .
Description . . . . . . . . . . . . . . . ..
BOTH SIDE HEADLAMPS (HI) ARE NOT
TURNED ON . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
BOTH SIDE HEADLAMPS (LO) ARE NOT
TURNED ON . . . . . . . . . . . . . ..
Description . . . . . . . . . . . . . . . ..
Revision: 2013 October
2014 JUKE
EXL-3
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Diagnosis Procedure . . . . . . . . . . . ...
PARKING, LICENSE PLATE, SIDE MARKER
AND TAIL LAMPS ARE NOT TURNED ON . ..
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
BOTH SIDE FRONT FOG LAMPS ARE NOT
TURNED ON . . . . . . . . . . . . . ...
Description . . . . . . . . . . . . . . . ..
Diagnosis Procedure . . . . . . . . . . . ...
PERIODIC MAINTENANCE . . . . . . .
HEADLAMP AIMING ADJUSTMENT . . . .
Description . . . . . . . . . . . . . . . ..
Aiming Adjustment Procedure . . . . . . . . .
FRONT FOG LAMP AIMING ADJUSTMENT .
Description . . . . . . . . . . . . . . . ..
Aiming Adjustment Procedure . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
HEADLAMP . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . ...
Disassembly and Assembly . . . . . . . . .
FRONT COMBINATION LAMP . . . . . . ..
Exploded View . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Replacement . . . . . . . . . . . . . . ...
Disassembly and Assembly . . . . . . . . .
DAYTIME RUNNING LIGHT . . . . . . .
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
FRONT FOG LAMP . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
OPTICAL SENSOR . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ..
Removal and Installation . . . . . . . . . ...
LIGHTING & TURN SIGNAL SWITCH . . ...
Removal and Installation . . . . . . . . . ...
HAZARD SWITCH . . . . . . . . . . ..
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
SIDE TURN SIGNAL LAMP . . . . . . .
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
HEADLAMP AIMING SWITCH . . . . . ...
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
REAR COMBINATION LAMP . . . . . . .
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
HIGH-MOUNTED STOP LAMP . . . . . ..
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
LICENSE PLATE LAMP . . . . . . . . .
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
Replacement . . . . . . . . . . . . . . .
REAR FOG LAMP . . . . . . . . . . ...
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
REAR REFLEX REFLECTOR . . . . . .
Exploded View . . . . . . . . . . . . . ...
Removal and Installation . . . . . . . . . ...
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . ..
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . ...
Bulb Specifications . . . . . . . . . . . .
Revision: 2013 October
2014 JUKE
EXL-4
< PRECAUTION >
[HALOGEN TYPE]
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009754460
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the “SRS AIR BAG” and “SEAT BELT” of this
Service Manual.
WARNING:
Always observe the following items for preventing accidental activation.
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision that would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see “SRS AIR BAG”.
• Never use electrical test equipment on any circuit related to the SRS unless instructed to in this Ser-
vice Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness
connectors.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
Always observe the following items for preventing accidental activation.
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, never use air or electric power tools or strike near the sensor(s) with
a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly causing
serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precautions for Removing of Battery Terminal
INFOID:0000000010239712
• When removing the 12V battery terminal, turn OFF the ignition
switch and wait at least 30 seconds.
NOTE:
ECU may be active for several tens of seconds after the ignition
switch is turned OFF. If the battery terminal is removed before ECU
stops, then a DTC detection error or ECU data corruption may
occur.
• For vehicles with the 2-batteries, be sure to connect the main bat-
tery and the sub battery before turning ON the ignition switch.
NOTE:
If the ignition switch is turned ON with any one of the terminals of
main battery and sub battery disconnected, then DTC may be
detected.
• After installing the 12V battery, always check "Self Diagnosis Result" of all ECUs and erase DTC.
NOTE:
The removal of 12V battery may cause a DTC detection error.
SEF289H
Revision: 2013 October
2014 JUKE
COMPONENT PARTS
EXL-5
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
SYSTEM DESCRIPTION
COMPONENT PARTS
Component Parts Location
INFOID:0000000009754461
*
1
: With front fog lamp models
*
2
: For NISMO models with daytime running light system
*
3
: With auto light system
*
4
: Except for NISMO models with daytime running light system
1.
Hazard switch
2.
Parking lamp
3.
Front side marker lamp
4.
Front turn signal lamp
5.
• Front fog lamp*
1
• Daytime running light*
2
6.
Headlamp
7.
TROL SYSTEM :
Component Parts Location"
.
8.
IPDM E/R
Refer to
9.
BCM
Refer to
SYSTEM : Component Parts Loca-
tion"
.
10. Combination switch
11.
Combination meter
12. Side turn signal lamp
13. Push-button ignition switch
14. Front door switch (driver side)
15. • Rear turn signal lamp
• Tail lamp
16. License plate lamp
17. Optical sensor*
3
18. Daytime running light relay 1*
4
19. Daytime running light relay 2*
4
A.
Engine room (RH)
JMLIA1484ZZ
Revision: 2013 October
2014 JUKE
EXL-6
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
COMPONENT PARTS
Component Description
INFOID:0000000009754462
*: With auto light system
Part
Description
BCM
Controls the exterior lighting system.
ECM
Transmits engine status signal to BCM. (via CAN communication)
IPDM E/R
Controls the integrated relay, and supplies voltage to the load according to the request
from BCM (via CAN communication).
Combination meter
• Blinks the turn signal indicator lamp and outputs the turn signal operating sound with
integrated buzzer according to the request from BCM (via CAN communication).
• Turns the tail lamp indicator lamp and high beam indicator lamp ON according to the
request from BCM (via CAN communication).
Optical sensor*
Optical sensor converts the outside brightness (lux) to voltage and transmits the opti-
cal sensor signal to BCM.
Combination switch
(Lighting & turn signal switch)
BCS-9, "COMBINATION SWITCH READING SYSTEM : System Descrip-
Door switch
DLK-13, "Component Description"
Hazard switch
Inputs the hazard switch signal to BCM.
Revision: 2013 October
2014 JUKE
SYSTEM
EXL-7
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
SYSTEM
HEADLAMP SYSTEM
HEADLAMP SYSTEM : System Diagram
INFOID:0000000009754463
HEADLAMP SYSTEM : System Description
INFOID:0000000009754464
OUTLINE
Headlamp is controlled by combination switch reading function and headlamp control function of BCM, and
relay control function of IPDM E/R.
HEADLAMP (LO) OPERATION
• BCM detects the combination switch condition with the combination switch reading function.
• BCM transmits the low beam request signal to IPDM E/R using CAN communication according to the head-
lamp (LO) ON condition.
Headlamp (LO) ON condition
- Lighting switch 2ND
- Lighting switch AUTO (auto light function ON judgment)
- Lighting switch AUTO, with the front fog lamp switch ON and the ignition switch ON*
• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low
beam request signal.
*: Only for models with Intelligent Key system
HEADLAMP (HI) OPERATION
• BCM transmits the high beam request signal to IPDM E/R and the combination meter using CAN communi-
cation according to the headlamp (HI) ON condition. At this time, BCM stops to transmit low beam request
signal.
Headlamp (HI) ON condition
- Lighting switch HI with the lighting switch 2ND or AUTO (auto light function ON judgment)
- Lighting switch PASS
- Lighting switch AUTO, with the front fog lamp switch ON, the ignition switch ON and lighting switch HI*
• Combination meter turns the high beam indicator lamp ON according to the high beam request signal.
• IPDM E/R turns the integrated headlamp high relay ON, and turns the headlamp ON according to the high
beam request signal.
*: Only for models with Intelligent Key system
FOLLOW ME HOME FUNCTION
When the driver is moving to the house entrance from the own vehicle, headlamp is kept still ON by the follow
me home function of BCM.
• When BCM detects the input of lighting switch PASS while all of following conditions satisfied, it transmits
the low beam request signal for a period of time to IPDM E/R through CAN communication.
Follow me home ON condition
JPLIA0167GB
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст