Nissan Juke (2014 year). Service Repair Manual — part 124
EXL-8
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
SYSTEM
- Ignition switch OFF
- Lighting switch OFF
• IPDM E/R turns the integrated headlamp low relay ON, and turns the headlamp ON according to the low
beam request signal.
• When in any of following conditions, follow me home function can be cancelled while follow me home func-
tion is operating.
Follow me home OFF condition
- Ignition switch is turned from OFF
→
ACC or ON
- Lighting switch is turned from OFF
→
ON
NOTE:
• Flash-to-pass operation illumination time for 1 time can be extended to approximately 30 seconds during
operation of follow me home function.
• Flash-to-pass operation can be illuminated continuously for approximately 60 seconds (flash-to-pass opera-
tion, 2 times), approximately 90 seconds (flash-to-pass operation, 3 times), and a maximum of approxi-
mately 120 seconds (flash-to-pass operation, 4 times).
• Follow me home function activating time can be set by CONSULT. Refer to
SULT Function (BCM - HEAD LAMP)"
HEADLAMP SYSTEM : Fail-safe
INFOID:0000000009754465
CAN COMMUNICATION CONTROL
When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If No CAN Communication Is Available With BCM
AUTO LIGHT SYSTEM
AUTO LIGHT SYSTEM : System Diagram
INFOID:0000000009754466
AUTO LIGHT SYSTEM : System Description
INFOID:0000000009754467
OUTLINE
• Auto light system is controlled by each function of BCM and IPDM E/R.
Control by BCM
- Combination switch reading function
Control part
Fail-safe operation
Headlamp
• Turns ON the headlamp low relay when the ignition switch is turned ON
• Turns OFF the headlamp low relay when the ignition switch is turned OFF
• Headlamp high relay OFF
JMLIA1254GB
Revision: 2013 October
2014 JUKE
SYSTEM
EXL-9
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
- Headlamp control function
- Auto light function
- Delay timer function
- Wiper linked auto lighting function
Control by IPDM E/R
- Relay control function
• Auto light system has the auto light function (with twilight lighting function), wiper linked auto lighting function
and delay timer function.
- Auto light function automatically turns ON/OFF the exterior lamps* and each illumination automatically,
depending on the outside brightness.
- Wiper linked auto lighting function automatically turns ON/OFF the exterior lamps* and each illumination
when the light switch is in the AUTO position, according to a front wiper operation.
- When auto light system turns the exterior lamps ON with the ignition switch OFF, delay timer function turns
the exterior lamps OFF, depending on the vehicle condition with the auto light function after a certain period
of time.
*: Headlamp (LO/HI), parking lamp, tail lamp, front fog lamp and side marker lamp (Headlamp HI and front fog
lamp depend on the combination switch condition.)
NOTE:
The settings of the twilight lighting function and the wiper linked auto lighting function can be changed with
CONSULT. Refer to
EXL-16, "HEADLAMP : CONSULT Function (BCM - HEAD LAMP)"
AUTO LIGHT FUNCTION (WITH TWILIGHT LIGHTING FUNCTION)
Description
• BCM detects the combination switch condition with the combination switch reading function.
• BCM supplies voltage to the optical sensor when the ignition switch is turned ON or ACC.
• Optical sensor converts outside brightness (lux) to voltage and transmits the optical sensor signal to BCM.
• BCM filters outside brightness based on the optical sensor signal and judges outside brightness.
• BCM detects change status of outside brightness according to outside brightness from the optical sensor
signal and filtered outside brightness. Based on the change status, BCM judges ON/OFF condition of the
exterior lamp.
• BCM transmits each request signal to IPDM E/R via CAN communication, according to ON/OFF condition by
the auto light function.
NOTE:
As to ON/OFF timing, the sensitivity depends on settings. The settings can be changed with CONSULT. Refer
to
EXL-16, "HEADLAMP : CONSULT Function (BCM - HEAD LAMP)"
.
WIPER LINKED AUTO LIGHTING FUNCTION
BCM turns the exterior lamps ON when detecting 4 operations of the front wiper work the light switch in AUTO
position.
NOTE:
BCM turns OFF the headlamps 3 seconds after the front wiper switch is turned from ON
⇒
OFF.
DELAY TIMER FUNCTION
BCM turns the exterior lamps OFF depending on the vehicle condition with the auto light function when the
ignition switch is turned OFF.
• Turns the exterior lamps OFF 5 minutes after detecting that any door opens. (Door switch ON).
• Turns the exterior lamps OFF a certain period of time* after closing all doors. (Door switch ON
→
OFF).
• Turns the exterior lamps OFF with the ignition switch ACC or the light switch OFF.
*: The preset time is 45 seconds. The timer operating time can be set by CONSULT. Refer to
LAMP : CONSULT Function (BCM - HEAD LAMP)"
.
NOTE:
When any position other than the light switch AUTO is set, the auto light system function switches to the exte-
rior lamp battery saver function.
DAYTIME RUNNING LIGHT SYSTEM
Revision: 2013 October
2014 JUKE
EXL-10
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
SYSTEM
DAYTIME RUNNING LIGHT SYSTEM : System Diagram
INFOID:0000000009754468
EXCEPT FOR NISMO MODELS
FOR NISMO MODELS
DAYTIME RUNNING LIGHT SYSTEM : System Description
INFOID:0000000009754469
EXCEPT FOR NISMO MODELS
Outline
• Turns the headlamp high ON (high beam at approximately half illumination) as the daytime running light.
• Daytime running light is controlled by daytime running light control function and combination switch reading
function of BCM, and relay control function of IPDM E/R.
Daytime Running Light Operation
• BCM detects the combination switch condition by the combination switch reading function.
• BCM detects the engine condition according to push-button ignition switch*
1
• BCM detects the engine condition by the engine status signal received from ECM using CAN communica-
tion*
2
.
• BCM detects the parking brake condition by the parking brake switch signal received from combination
meter using CAN communication.
• BCM transmits the daytime running light request signal to IPDM E/R using CAN communication according to
the daytime running light ON condition.
Daytime running light ON condition
- Engine running
JMLIA1487GB
JMLIA3997GB
Revision: 2013 October
2014 JUKE
SYSTEM
EXL-11
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
- Lighting switch OFF or 1ST
- Parking brake switch OFF
• IPDM E/R controls the daytime running light relay-2 (ground-side) to turn ON according to the daytime run-
ning light request signal.
• Power is supplied from the daytime running light relay 2 through headlamp high (RH) and IPDM E/R to
headlamp high (LH). And high beam headlamps are illuminated (approximately half illumination) as the day-
time running light.
*
1
: Only for models with Intelligent Key system
*
2
: Only for models without Intelligent Key system
NOTE:
• Daytime running light relay 1 is turned ON when headlamp is low.
• Daytime running light relay 1 is OFF to cut voltage of headlamp low circuit when daytime running light is ON.
FOR NISMO MODELS
Outline
• Daytime running light system is turned on daytime running light.
• Daytime running light is controlled by daytime running light control function and combination switch reading
function of BCM, and relay control function of IPDM E/R.
Daytime Running Light Operation
• BCM detects the combination switch condition by the combination switch reading function.
• BCM detects the engine condition by the engine status signal received from ECM with CAN communication.
• BCM detects the parking brake condition by the parking brake switch signal received from combination
meter with CAN communication.
• BCM detects ENGINE RUNNING condition by engine status signal and RELEASE condition by parking
brake switch signal. And then, BCM transmits the daytime running light request signal to IPDM E/R with
CAN communication according to any of the daytime running light ON condition.
Daytime running light ON condition
- Lighting switch OFF
- Lighting switch AUTO and auto light judgement OFF
• IPDM E/R turns the integrated daytime running light relay ON, and turns the daytime running light ON
according to the daytime running light request signal.
FRONT FOG LAMP SYSTEM
FRONT FOG LAMP SYSTEM : System Diagram
INFOID:0000000009754470
FRONT FOG LAMP SYSTEM : System Description
INFOID:0000000009754471
OUTLINE
Front fog lamp is controlled by combination switch reading function, front fog lamp control function of BCM,
and relay control function of IPDM E/R.
FRONT FOG LAMP OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the front fog lights request signal to IPDM E/R via CAN communication according to the front
fog lamp ON condition.
Front fog lamp ON condition
- Front fog lamp switch ON and any of the following. (except for the high beam ON)
JMLIA1154GB
Revision: 2013 October
2014 JUKE
EXL-12
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
SYSTEM
• Lighting switch 2ND
• Lighting switch AUTO (auto light function ON judgment)
IPDM E/R turns the integrated front fog lamp relay ON, and turns the front fog lamp ON according to the front
fog lights request signal.
FRONT FOG LAMP SYSTEM : Fail-safe
INFOID:0000000009754472
CAN COMMUNICATION CONTROL
When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If No CAN Communication Is Available With BCM
TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM
TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Diagram
INFOID:0000000009754473
TURN SIGNAL AND HAZARD WARNING LAMP SYSTEM : System Description
INFOID:0000000009754474
OUTLINE
Turn signal lamp and the hazard warning lamp are controlled by combination switch reading function and the
flasher control function of BCM.
TURN SIGNAL LAMP OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM supplies voltage to the right (left) turn signal lamp circuit when the ignition switch is ON and the turn
signal switch is in the right (left) position. BCM blinks the turn signal lamp.
HAZARD WARNING LAMP OPERATION
BCM supplies voltage to both turn signal lamp circuits when the hazard switch is ON. BCM blinks the hazard
warning lamp.
TURN SIGNAL INDICATOR LAMP AND TURN SIGNAL OPERATION
• BCM transmits the turn signal indicator lamp signal to the combination meter using CAN communication
while the turn signal lamp and the hazard warning lamp are operating.
• Combination meter outputs the turn signal sound with the integrated buzzer while blinking the turn signal
indicator lamp according to the turn signal indicator lamp signal.
HIGH FLASHER OPERATION
• BCM detects the turn signal lamp circuit status from the current value.
Control part
Fail-safe operation
Front fog lamp
Front fog lamp relay OFF
JPLIA0180GB
Revision: 2013 October
2014 JUKE
SYSTEM
EXL-13
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
• BCM increases the turn signal lamp blinking speed if the bulb or harness open is detected with the turn sig-
nal lamp operating.
NOTE:
The blinking speed is normal while operating the hazard warning lamp.
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM : System Di-
agram
INFOID:0000000009754475
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM : System De-
scription
INFOID:0000000009754476
OUTLINE
Parking, license plate, side marker and tail lamps are controlled by combination switch reading function and
headlamp control function of BCM, and relay control function of IPDM E/R.
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMPS OPERATION
• BCM detects the combination switch condition by the combination switch reading function.
• BCM transmits the position light request signal to IPDM E/R and the combination meter via CAN communi-
cation according to the ON/OFF condition of the parking, license plate, side marker and tail lamps.
Parking, license plate, side marker and tail lamps ON condition
- Lighting switch 1ST
- Lighting switch 2ND
- Lighting switch AUTO, and the auto light function ON judgment
- Lighting switch AUTO, with the front fog lamp switch ON and the ignition switch ON*
• IPDM E/R turns the integrated tail lamp relay ON and turns the parking, license plate, side marker and tail
lamps ON according to the position light request signal.
• Combination meter turns the tail lamp indicator lamp ON according to the position light request signal.
*: Only for models with Intelligent Key system
PARKING, LICENSE PLATE, SIDE MARKER AND TAIL LAMP SYSTEM : Fail-safe
INFOID:0000000009754477
CAN COMMUNICATION CONTROL
When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If No CAN Communication Is Available With BCM
JMLIA1349GB
Revision: 2013 October
2014 JUKE
EXL-14
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
SYSTEM
EXTERIOR LAMP BATTERY SAVER SYSTEM
EXTERIOR LAMP BATTERY SAVER SYSTEM : System Diagram
INFOID:0000000009754478
EXTERIOR LAMP BATTERY SAVER SYSTEM : System Description
INFOID:0000000009754479
OUTLINE
• Exterior lamp battery saver system is controlled by each function of BCM and IPDM E/R.
Control by BCM
- Combination switch reading function
- Headlamp control function
- Exterior lamp battery saver function
Control by IPDM E/R
- Relay control function
• BCM turns the exterior lamps* OFF after a period of time to prevent the battery from over-discharge when
the ignition switch is turned OFF with the exterior lamps ON.
*: Headlamp (LO/HI), parking lamp, tail lamp, side marker lamp, license plate lamp and front fog lamp
EXTERIOR LAMP BATTERY SAVER ACTIVATION
BCM activates the timer and turns the exterior lamp OFF 5 minutes after the ignition switch is turned from ON
→
OFF with the exterior lamps ON.
NOTE:
• Headlamp control function turns the exterior lamps ON normally when the ignition switch is turned ACC or
the engine started (both before and after the exterior lamp battery saver is turned OFF).
• The timer starts at the time that the lighting switch is turned from OFF
→
1ST or 2ND with the exterior lamps
OFF.
Control part
Fail-safe operation
• Parking lamp
• License plate lamp
• Illumination
• Tail lamp
• Side marker lamp
• Turns ON the tail lamp relay when the ignition switch is turned ON
• Turns OFF the tail lamp relay when the ignition switch is turned OFF
JPLIA1037GB
Revision: 2013 October
2014 JUKE
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
EXL-15
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010296660
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
*: For models with automatic A/C, this diagnosis mode is not used.
FREEZE FRAME DATA (FFD)
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT.
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
Air conditioning system
AIR CONDITONER
×
×
*
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
RAP
RETAINED PWR
×
Signal buffer system
SIGNAL BUFFER
×
×
TPMS
AIR PRESSURE MONITOR
×
×
×
Revision: 2013 October
2014 JUKE
EXL-16
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
NOTE:
*: Power position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in the P position (A/T models
and CVT models), and any of the following conditions are met.
• Closing door
• Opening door
• Door is locked using door request switch
• Door is locked using Intelligent Key
The power position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEAD LAMP)
INFOID:0000000009754481
WORK SUPPORT
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power position is “LOCK”*.)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power position is “OFF”.)
LOCK>ACC
While turning power position from “LOCK”* *to “ACC”
ACC>ON
While turning power position from “ACC” to “IGN”
RUN>ACC
While turning power position from “RUN” to “ACC” (Vehicle is
stopping and selector lever is except P position.)
CRANK>RUN
While turning power position from “CRANKING” to “RUN” (From
cranking up the engine to run it)
RUN>URGENT
While turning power position from “RUN“ to “ACC” (Emergency
stop operation)
ACC>OFF
While turning power position from “ACC” to “OFF”
OFF>LOCK
While turning power position from “OFF” to “LOCK”*
OFF>ACC
While turning power position from “OFF” to “ACC”
ON>CRANK
While turning power position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power position is
“OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power position is
“LOCK”*.) to low power consumption mode
LOCK
Power position is “LOCK”*
OFF
Power position is “OFF” (Ignition switch OFF)
ACC
Power position is “ACC” (Ignition switch ACC)
ON
Power position is “IGN” (Ignition switch ON with engine stopped)
ENGINE RUN
Power position is “RUN” (Ignition switch ON with engine running)
CRANKING
Power position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
Revision: 2013 October
2014 JUKE
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
EXL-17
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
*
1
: For models without auto light system, this item is displayed, but cannot be used.
*
2
: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Service item
Setting item
Setting
CUSTOM A/LIGHT SET-
TING*
1
MODE 1*
2
Normal
MODE 2
More sensitive setting than normal setting (Turns ON earlier than normal opera-
tion)
MODE 3
More sensitive setting than MODE 2 (Turns ON earlier than MODE 2)
MODE 4
Less sensitive setting than normal setting (Turns ON later than normal operation)
BATTERY SAVER SET
On*
2
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
ILL DELAY SET*
1
MODE 1*
2
45 sec.
Sets delay timer function timer operation time
(All doors closed)
MODE 2
Without the
function
MODE 3
30 sec.
MODE 4
60 sec.
MODE 5
90 sec.
MODE 6
120 sec.
MODE 7
150 sec.
MODE 8
180 sec.
HEAD LIGHT TIMER
MODE 1
10 sec.
Sets follow me home function activating time
MODE 2
*2
30 sec.
AUTO LIGHT LOGIC SET*
1
MODE 1*
2
With twilight ON custom & with wiper INT, LO and HI
MODE 2
With twilight ON custom & with wiper LO and HI
MODE 3
With twilight ON custom & without
MODE 4
Without twilight ON custom & with wiper INT, LO and HI
MODE 5
Without twilight ON custom & with wiper LO and HI
MODE 6
Without twilight ON custom & without
Monitor item
[Unit]
Description
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
ENGINE STATE
[Stop/Stall/Crank/Run]
Indicates [Stop/Stall/Crank/Run] condition of engine states
VEH SPEED 1
[km/h]
Display the vehicle speed signal received from combination meter by numerical value
[Km/h]
Revision: 2013 October
2014 JUKE
EXL-18
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
*: For models without front fog lamp, this item is displayed, but cannot be monitored.
ACTIVE TEST
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW
[On/Off]
FR FOG SW*
[On/Off]
DOOR SW-DR
[On/Off]
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
[On/Off]
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
[On/Off]
Indicated [On/Off] condition of rear door switch RH
DOOR SW- RL
[On/Off]
Indicated [On/Off] condition of rear door switch LH
DOOR SW-BK
[On/Off]
Indicated [On/Off] condition of back door switch
OPTICAL SENSOR
[On/Off/NG]
NOTE:
This item is displayed, but cannot be monitored
OPTI SEN (DTCT)
[V]
The value of outside brightness voltage input from the optical sensor
OPTI SEN (FILT)
[V]
The value of outside brightness voltage filtered by BCM
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
On
Transmits the position light request signal to IPDM E/R via CAN commu-
nication to turn the tail lamp ON
Off
Stops the tail lamp request signal transmission
HEAD LAMP
Hi
Transmits the high beam request signal via CAN communication to turn
the headlamp (HI)
Lo
Transmits the low beam request signal via CAN communication to turn
the headlamp (LO)
Off
Stops the high & low beam request signal transmission
Revision: 2013 October
2014 JUKE
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
EXL-19
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
*
1
: Except for NISMO models without front fog lamp, this item is displayed, but cannot be tested.
*
2
: For NISMO models with daytime running light system, this item is displayed, but cannot be tested.
*
3
: Except for NISMO models with daytime running light system.
*
4
: For NISMO models with daytime running light system.
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER)
INFOID:0000000009754482
WORK SUPPORT
*: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
FR FOG LAMP*
1
On
• Transmits the front fog lights request signal to IPDM E/R via CAN com-
munication to turn the front fog lamp ON*
3
• Transmits the daytime running light request signal to IPDM E/R via
CAN communication to turn the daytime running light ON*
4
Off
• Stops the front fog light request signal transmission*
3
• Stops the daytime running light request signal transmission*
4
DAYTIME RUNNING LIGHT*
2
On
Transmits the daytime running light request signal via CAN communica-
tion to IPDM E/R
Off
Stop the daytime running light request signal transmission
ILL DIM SIGNAL
On
NOTE:
This item is indicated, but can not tested
Off
Test item
Operation
Description
Service item
Setting item
Setting
HAZARD ANSWER
BACK
Lock Only
With locking only
Sets the hazard warning lamp answer back function
when the door is lock/unlock with the request switch or
the Intelligent Key.
Unlk Only
With unlocking only
Lock&Unlk
*
With locking/unlocking
Off
Without the function
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
Indicated [On/Off] condition of door request switch (driver side)
REQ SW-AS
[On/Off]
Indicated [On/Off] condition of door request switch (passenger side)
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
[On/Off]
The switch status input from the hazard switch
RKE-LOCK
[On/Off]
Indicates [On/Off] condition of LOCK signal from Intelligent Key
Revision: 2013 October
2014 JUKE
EXL-20
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
ACTIVE TEST
RKE-UNLOCK
[On/Off]
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-PANIC
[On/Off]
Indicates [On/Off] condition of PANIC button of Intelligent Key
Monitor item
[Unit]
Description
Test item
Operation
Description
FLASHER
RH
Outputs the voltage to turn the right side turn signal lamps ON
LH
Outputs the voltage to turn the left side turn signal lamps ON
Off
Stops the voltage to turn the turn signal lamps OFF
Revision: 2013 October
2014 JUKE
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
EXL-21
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010296662
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEAD LAMP)
INFOID:0000000009754484
WORK SUPPORT
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp control
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
Air conditioning system
AIR CONDITONER
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
×
Signal buffer system
SIGNAL BUFFER
×
×
Panic alarm
PANIC ALARM
×
TPMS
AIR PRESSUE MONITOR
×
×
×
Revision: 2013 October
2014 JUKE
EXL-22
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
*: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Service item
Setting item
Setting
BATTERY SAVER SET
On*
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
ILL DELAY SET
MODE 1
NOTE:
This item is displayed but is not operated
MODE 2
MODE 3
MODE 4
MODE 5
MODE 6
MODE 7
MODE 8
HEAD LIGHT TIMER
MODE 1
10 sec.
Sets follow me home function activating time
MODE 2
*
30 sec.
AUTO LIGHT LOGIC SET
MODE 1
NOTE:
This item is displayed but is not operated
MODE 2
MODE 3
MODE 4
MODE 5
MODE 6
Monitor item
[Unit]
Description
IGN ON SW
[On/Off]
Indicated [On/Off] condition of ignition switch in ON position
ACC ON SW
[On/Off]
Indicates [On/Off] condition of ignition switch in ACC position
VEHICLE SPEED
[km/h]
Display the vehicle speed signal received from combination meter by numerical value
[Km/h]
HI BEAM SW
[On/Off]
Each switch status that BCM judges from the combination switch reading function
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
FR FOG SW*
[On/Off]
AUTO LIGHT SW
[On/Off]
NOTE:
This item is indicated, but can not monitored
DOOR SW-DR
[On/Off]
The switch status input from front door switch (driver side)
DOOR SW-AS
[On/Off]
The switch status input from front door switch (passenger side)
Revision: 2013 October
2014 JUKE
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
EXL-23
< SYSTEM DESCRIPTION >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
*: For models without front fog lamp, this item is displayed but is not monitored.
ACTIVE TEST
*
1
: For models without front fog lamp, this item is displayed but is not tested.
*
2
: For models without daytime running light system, this item is not displayed.
FLASHER
DOOR SW-RR
[On/Off]
The switch status input from rear door switch RH
DOOR SW- RL
[On/Off]
The switch status input from rear door switch LH
BACK DOOR SW
[On/Off]
The switch status input from back door switch
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
KEY ON SW
[On/Off]
Indicated [On/Off] condition of key switch
KEYLESS LOCK
[On/Off]
Indicated [On/Off] condition of lock signal from key fob
PKB SW
[On/Off]
The parking brake switch status received from combination meter with CAN commu-
nication
ENGINE RUN
[On/Off]
The engine status received from ECM with CAN communication
OPTI SEN (DTCT)
[V]
NOTE:
This item is indicated, but can not monitored
OPTI SEN (FILT)
[V]
NOTE:
This item is indicated, but can not monitored
LIG SEN COND
[On/Off/NG]
NOTE:
This item is indicated, but can not monitored
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
On
Transmits the position light request signal to IPDM E/R with CAN com-
munication to turn the tail lamp ON
Off
Stops the tail lamp request signal transmission
HEAD LAMP
Hi
Transmits the high beam request signal with CAN communication to turn
the headlamp (HI)
Lo
Transmits the low beam request signal with CAN communication to turn
the headlamp (LO)
Off
Stops the high & low beam request signal transmission
FR FOG LAMP*
1
On
Transmits the front fog lights request signal to IPDM E/R with CAN com-
munication to turn the front fog lamp ON
Off
Stops the front fog lights request signal transmission
DAYTIME RUNNING LIGHT*
2
On
Transmits the daytime running light request signal via CAN communica-
tion to IPDM E/R
Off
Stop the daytime running light request signal transmission
ILL DIM SIGNAL
On
NOTE:
This item is indicated, but can not tested
Off
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст