Nissan Juke (2014 year). Service Repair Manual — part 54
REMOTE KEYLESS ENTRY RECEIVER
DLK-89
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY RECEIVER
Component Function Check
INFOID:0000000009753996
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “RKE OPE COUN1” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Remote keyless entry receiver is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009753997
1.
CHECK REMOTE KEYLESS ENTRY RECEIVER POWER SUPPLY
1.
Turn ignition switch OFF.
2.
Disconnect remote keyless entry receiver connector.
3.
Check voltage between remote keyless entry receiver harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
DETECT MALFUNCTIONING PART
Check the following.
• 10 A fuse (No. 7)
• Harness for open or short between remote keyless entry receiver and battery
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK REMOTE KEYLESS ENTRY RECEIVER GROUND CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
Monitor item
Condition
RKE OPE COUN1
Checks whether value changes when operating Intelligent Key
(+)
(–)
Voltage
Remote keyless entry receiver
Connector
Terminal
M75
1
Ground
Battery voltage
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M68
18
M75
4
Existed
BCM
Ground
Continuity
Connector
Terminal
M68
18
Existed
Revision: 2013 October
2014 JUKE
DLK-90
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
REMOTE KEYLESS ENTRY RECEIVER
4.
CHECK REMOTE KEYLESS ENTRY RECEIVER OUTPUT SIGNAL
1.
Reconnect BCM connector and remote keyless entry receiver connector.
2.
Check signal between remote keyless entry receiver harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace remote keyless entry receiver.
5.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT
1.
Disconnect BCM connector and remote keyless entry receiver connector.
2.
Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
NO
>> Repair or replace harness.
6.
CHECK INTERMITTENT INCIDENT
GI-46, "Intermittent Incident"
>> INSPECTION END
(+)
(–)
Condition
Signal
(Reference value)
Remote keyless entry receiver
Connector
Terminal
M75
2
Ground
Waiting
12 V
Press the Intelligent
Key lock or unlock
button
JMMIA0572GB
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M68
38
M75
2
Existed
BCM
Ground
Continuity
Connector
Terminal
M68
38
Not existed
Revision: 2013 October
2014 JUKE
SHIFT P WARNING LAMP
DLK-91
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SHIFT P WARNING LAMP
Component Function Check
INFOID:0000000009753998
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “LCD” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Shift P warning lamp is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009753999
1.
CHECK SHIFT P WARNING LAMP
MWI-20, "On Board Diagnosis Function"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-46, "Intermittent Incident"
.
>> INSPECTION END
Monitor item
Status
LCD
SFT P
Shift P warning lamp
Turns ON
Revision: 2013 October
2014 JUKE
DLK-92
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
UNLOCK SENSOR
UNLOCK SENSOR
Component Function Check
INFOID:0000000009754000
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “UNLK SEN -DR” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Unlock sensor is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000009754001
1.
CHECK BCM OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check signal between front door lock assembly (driver side) harness connector and ground using oscillo-
scope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK UNLOCK SENSOR CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
Monitor item
Condition
Status
UNLK SEN -DR
Driver side door
Lock
OFF
Unlock
ON
(+)
(–)
Signal
(Reference value)
Front door lock assembly (driver side)
Connector
Terminal
D38
3
Ground
PKIB4960J
BCM
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M68
31
D38
3
Existed
BCM
Ground
Continuity
Connector
Terminal
M68
31
Not existed
Revision: 2013 October
2014 JUKE
UNLOCK SENSOR
DLK-93
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
NO
>> Repair or replace harness.
3.
CHECK UNLOCK SENSOR GROUND CIRCUIT
Check continuity between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK UNLOCK SENSOR
DLK-93, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace front door lock assembly (driver side).
5.
CHECK INTERMITTENT INCIDENT
GI-46, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000009754002
1.
CHECK UNLOCK SENSOR
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check continuity between front door lock assembly (driver side) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front lock assembly (driver side).
Front door lock assembly (driver side)
Ground
Continuity
Connector
Terminal
D38
4
Existed
Front door lock assembly (driver side)
Condition
Continuity
Terminal
3
4
Driver side door
Unlock
Existed
Lock
Not existed
Revision: 2013 October
2014 JUKE
DLK-94
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
SYMPTOM DIAGNOSIS
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK
SWITCH
ALL DOOR
ALL DOOR : Description
INFOID:0000000009754003
All doors do not lock/unlock using door lock and unlock switch.
ALL DOOR : Diagnosis Procedure
INFOID:0000000009754004
1.
CHECK DOOR LOCK AND UNLOCK SWITCH
Check door lock and unlock switch.
Refer to
DLK-77, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK DOOR LOCK ACTUATOR
Check front door lock assembly (driver side).
Refer to
DLK-72, "DRIVER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-90, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000009754005
Driver side door does not lock/unlock using door lock and unlock switch.
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000009754006
1.
CHECK DOOR LOCK ACTUATOR
Check front door lock assembly (driver side).
Refer to
DLK-72, "DRIVER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-90, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
PASSENGER SIDE
Revision: 2013 October
2014 JUKE
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
DLK-95
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
PASSENGER SIDE : Description
INFOID:0000000009754007
Passenger side door does not lock/unlock using door lock and unlock switch.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000009754008
1.
CHECK DOOR LOCK ACTUATOR
Check front door lock assembly (passenger side).
Refer to
DLK-73, "PASSENGER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-90, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
REAR LH
REAR LH : Description
INFOID:0000000009754009
Rear LH side door does not lock/unlock using door lock and unlock switch.
REAR LH : Diagnosis Procedure
INFOID:0000000009754010
1.
CHECK DOOR LOCK ACTUATOR
Check rear door lock assembly LH.
Refer to
DLK-74, "REAR LH : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-90, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
REAR RH
REAR RH : Description
INFOID:0000000009754011
Rear RH side door does not lock/unlock using door lock and unlock switch.
REAR RH : Diagnosis Procedure
INFOID:0000000009754012
1.
CHECK DOOR LOCK ACTUATOR
Check rear door lock assembly RH.
Refer to
DLK-75, "REAR RH : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-90, "Removal and Installation"
.
Revision: 2013 October
2014 JUKE
DLK-96
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
Revision: 2013 October
2014 JUKE
DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH
DLK-97
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH
ALL DOOR REQUEST SWITCHES
ALL DOOR REQUEST SWITCHES : Description
INFOID:0000000009754013
All doors do not lock/unlock using all door request switches.
ALL DOOR REQUEST SWITCHES : Diagnosis Procedure
INFOID:0000000009754014
1.
CHECK REMOTE KEYLESS ENTRY FUNCTION
Check remote keyless entry function.
Does door lock/unlock with Intelligent Key button?
YES
>> GO TO 2.
NO
>> Refer to
DLK-21, "REMOTE KEYLESS ENTRY FUNCTION : System Description"
2.
CHECK “LOCK/UNLOCK BY I-KEY” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT.
2.
Select “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT” mode.
3.
Check “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT”.
Refer to
DLK-31, "INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT”.
3.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-81, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK INSIDE KEY ANTENNA
Check inside key antenna.
• Instrument center: Refer to
.
• Luggage room: Refer to
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
CHECK OUTSIDE KEY ANTENNA
Check outside key antenna.
• Driver side: Refer to
.
.
• Rear bumper: Refer to
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace the malfunctioning parts.
6.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-90, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
DRIVER SIDE DOOR REQUEST SWITCH
Revision: 2013 October
2014 JUKE
DLK-98
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH
DRIVER SIDE DOOR REQUEST SWITCH : Description
INFOID:0000000009754015
All doors do not lock/unlock using driver side door request switch.
DRIVER SIDE DOOR REQUEST SWITCH : Diagnosis Procedure
INFOID:0000000009754016
1.
CHECK DRIVER SIDE DOOR REQUEST SWITCH
Check driver side door request switch.
Refer to
DLK-79, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK OUTSIDE KEY ANTENNA
Check outside key antenna (driver side).
Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-90, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
PASSENGER SIDE DOOR REQUEST SWITCH
PASSENGER SIDE DOOR REQUEST SWITCH : Description
INFOID:0000000009754017
All doors do not lock/unlock using passenger side door request switch.
PASSENGER SIDE DOOR REQUEST SWITCH : Diagnosis Procedure
INFOID:0000000009754018
1.
CHECK PASSENGER SIDE DOOR REQUEST SWITCH
Check passenger side door request switch.
Refer to
DLK-79, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK OUTSIDE KEY ANTENNA
Check outside key antenna (passenger side).
Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-90, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
BACK DOOR REQUEST SWITCH
Revision: 2013 October
2014 JUKE
DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH
DLK-99
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR REQUEST SWITCH : Description
INFOID:0000000009754019
All doors do not lock/unlock using back door request switch.
BACK DOOR REQUEST SWITCH : Diagnosis Procedure
INFOID:0000000009754020
1.
CHECK BACK DOOR REQUEST SWITCH
Check back door request switch.
Refer to
DLK-67, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK OUTSIDE KEY ANTENNA
Check outside key antenna (rear bumper).
Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-90, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
Revision: 2013 October
2014 JUKE
DLK-100
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR DOES NOT LOCK/UNLOCK WITH DOOR KEY CYLINDER OPERATION
DOOR DOES NOT LOCK/UNLOCK WITH DOOR KEY CYLINDER OPERA-
TION
Diagnosis Procedure
INFOID:0000000009754021
1.
CHECK POWER DOOR LOCK OPERATION
Check power door lock operation.
Does door lock/unlock with door lock and unlock switch?
YES
>> GO TO 2.
NO
>> Refer to
DLK-77, "Component Function Check"
.
2.
CHECK DOOR KEY CYLINDER SWITCH
Check door key cylinder switch.
Refer to
DLK-70, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-90, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
Revision: 2013 October
2014 JUKE
DOOR DOES NOT LOCK/UNLOCK WITH INTELLIGENT KEY
DLK-101
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR DOES NOT LOCK/UNLOCK WITH INTELLIGENT KEY
Diagnosis Procedure
INFOID:0000000009754022
1.
CHECK INTELLIGENT KEY
For Intelligent Key that cannot be used for door lock and unlock, check that the Intelligent Key belongs to the
vehicle to be checked.
Does the Intelligent Key belong to the vehicle to checked?
YES
>> GO TO 2.
NO
>> Check Intelligent Key button operation with registered Intelligent Key belonging to the vehicle.
2.
CHECK INTELLIGENT KEY LOW BATTERY WARNING
Check that the Intelligent Key low battery warning is operated.
Is the Intelligent Key low battery warning operated?
YES
>> GO TO 6.
NO-1
>> With another registered Intelligent Key: GO TO 3.
NO-2
>> Without another registered Intelligent Key: GO TO 4.
3.
CHECK INTELLIGENT KEY BUTTON OPERATION
Check that door lock and unlock can be performed by operating the buttons of another registered Intelligent
Key.
Can door lock and unlock be performed with another registered Intelligent Key?
YES
>> GO TO 4.
NO
>> GO TO 7.
4.
CHECK ENGINE START
While depressing the brake pedal, contact the backside of the Intelligent Key that cannot be used to perform
door lock and unlock operation to the push-button ignition switch. Operate the push-button ignition switch, and
check that the vehicle is in START status.
Is the vehicle in START status?
YES
>> GO TO 6.
NO
>> GO TO 5.
5.
CHECK INTELLIGENT KEY
Check the inside of the Intelligent Key for rust or corrosion by water. Simultaneously check the internal circuits
for damage.
Is the vehicle in START status?
YES
>> GO TO 6.
NO
>> Replace Intelligent Key.
6.
CHECK INTELLIGENT KEY BATTERY
Check the Intelligent Key battery.
Refer to
DLK-85, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace Intelligent Key battery.
7.
CHECK POWER DOOR LOCK OPERATION
Check door lock/unlock using door lock and unlock switch.
Does door lock/unlock using door lock and unlock switch?
YES
>> GO TO 8.
NO
>> Refer to
DLK-94, "ALL DOOR : Diagnosis Procedure"
8.
CHECK REMOTE KEYLESS ENTRY RECEIVER
Check remote keyless entry receiver.
Refer to
DLK-89, "Component Function Check"
.
Revision: 2013 October
2014 JUKE
DLK-102
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
DOOR DOES NOT LOCK/UNLOCK WITH INTELLIGENT KEY
Is the inspection result normal?
YES
>> GO TO 9.
NO
>> Repair or replace the malfunctioning parts.
9.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-81, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 10.
NO
>> Repair or replace the malfunctioning parts.
10.
REPLACE INTELLIGENT KEY
1.
Replace Intelligent Key.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Replace BCM. Refer to
BCS-90, "Removal and Installation"
Revision: 2013 October
2014 JUKE
IGNITION POSITION WARNING FUNCTION DOES NOT OPERATE
DLK-103
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
IGNITION POSITION WARNING FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000009754023
1.
CHECK DTC WITH BCM
Check that DTC is not detected with BCM.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Refer to
2.
CHECK POWER DOOR LOCK OPERATION
Check power door lock operation.
Does door lock/unlock with driver side door lock knob and door key cylinder?
YES
>> GO TO 3.
NO
>> Refer to
3.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-81, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-90, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
Revision: 2013 October
2014 JUKE
DLK-104
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
SELECTIVE UNLOCK FUNCTION DOES NOT OPERATE
SELECTIVE UNLOCK FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000009754024
1.
CHECK “DOOR LOCK–UNLOCK SET” SETTING IN “WORK SUPPORT”
1.
Select “DOOR LOCK” of “BCM” using CONSULT.
2.
Select “DOOR LOCK-UNLOCK SET” in “WORK SUPPORT” mode.
3.
Check “DOOR LOCK-UNLOCK SET” in “WORK SUPPORT”
Refer to
DLK-29, "DOOR LOCK : CONSULT Function (BCM - DOOR LOCK)"
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Set “DOOR LOCK-UNLOCK SET” in “WORK SUPPORT”.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-90, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-46, "Intermittent Incident"
.
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст