Nissan Juke (2014 year). Service Repair Manual — part 186
PCS-42
< SYSTEM DESCRIPTION >
[IPDM E/R (WITHOUT I-KEY)]
SYSTEM
- CAN communication is normally performed with other control units.
- Individual unit control by IPDM E/R is normally performed.
Low power consumption mode (sleep)
- Low power consumption control is active.
- CAN transmission is stopped.
SLEEP MODE ACTIVATION
• IPDM E/R judges that the sleep-ready conditions are fulfilled when the ignition switch is OFF and none of the
conditions below are present. Then it transmits a sleep-ready signal (ready) to BCM via CAN communica-
tion.
- Outputting signals to actuators
- Switches or relays operating
- Output requests are being received from control units via CAN communication.
• IPDM E/R stops CAN communication and enters the low power consumption mode when it receives a sleep
wake up signal (sleep) from BCM and the sleep-ready conditions are fulfilled.
WAKE-UP OPERATION
• IPDM E/R changes from the low power consumption mode to the normal mode when it receives a sleep
wake-up signal (wake up) from BCM or any of the following conditions is fulfilled. In addition, it transmits a
sleep-ready signal (not-ready) to BCM via CAN communication to report the CAN communication start.
- Ignition switch ON
- An output request is received from a control unit via CAN communication.
Revision: 2013 October
2014 JUKE
PCS
DIAGNOSIS SYSTEM (IPDM E/R)
PCS-43
< SYSTEM DESCRIPTION >
[IPDM E/R (WITHOUT I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DIAGNOSIS SYSTEM (IPDM E/R)
Diagnosis Description
INFOID:0000000009751946
AUTO ACTIVE TEST
Description
In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Rear window defogger
• Front wiper motor
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
• Headlamp (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan
Operation Procedure
CAUTION:
Wiper arm interferes with hood when wiper is operated while wiper arm is in the raised position.
Always perform auto active test without setting wiper arm in the raised position. Always pour water on
front windshield glass in advance to auto active test so that damage on front windshield glass surface
is prevented.
1.
Turn the ignition switch OFF.
2.
Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
CAUTION:
Close passenger door.
3.
Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
CAUTION:
Engine starts when ignition switch is turned ON while brake pedal is depressed.
4.
After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
• When auto active test mode has to be cancelled halfway through test, turn the ignition switch OFF.
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to
Inspection in Auto Active Test Mode
When auto active test mode is actuated, the following operation sequence is repeated 3 times.
Operation
sequence
Inspection location
Operation
1
Rear window defogger
10 seconds
2
Front wiper motor
LO for 5 seconds
→
HI for 5 seconds
3
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
10 seconds
4
Headlamp
LO for 10 seconds
→
HI ON
⇔
OFF 5 times
5
A/C compressor (magnet clutch)
ON
⇔
OFF 5 times
6
Cooling fan
50% duty for 5 seconds
→
100% duty for 5 seconds
Revision: 2013 October
2014 JUKE
PCS-44
< SYSTEM DESCRIPTION >
[IPDM E/R (WITHOUT I-KEY)]
DIAGNOSIS SYSTEM (IPDM E/R)
Concept of auto active test
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode
JMMIA0588GB
Symptom
Inspection contents
Possible cause
Rear window defogger does not operate
Perform auto active test.
Does the rear window defog-
ger operate?
YES
BCM signal input circuit
NO
• Rear window defogger
• Rear window defogger ground circuit
• Harness or connector between IPDM E/R
and rear window defogger
• IPDM E/R
Any of the following components do not
operate
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
• Headlamp (HI, LO)
• Front wiper motor
Perform auto active test.
Does the applicable system
operate?
YES
BCM signal input circuit
NO
• Lamp or motor
• Lamp or motor ground circuit
• Harness or connector between IPDM E/R
and applicable system
• IPDM E/R
A/C compressor does not operate
Perform auto active test.
Does the magnet clutch oper-
ate?
YES
• A/C amp. signal input circuit
• CAN communication signal between A/C
amp. and ECM
• CAN communication signal between ECM
and IPDM E/R
NO
• Magnet clutch
• Harness or connector between IPDM E/R
and magnet clutch
• IPDM E/R
Revision: 2013 October
2014 JUKE
PCS
DIAGNOSIS SYSTEM (IPDM E/R)
PCS-45
< SYSTEM DESCRIPTION >
[IPDM E/R (WITHOUT I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
CONSULT Function (IPDM E/R)
INFOID:0000000009751947
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
SELF DIAGNOSTIC RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Cooling fan does not operate
Perform auto active test.
Does the cooling fan operate?
YES
• ECM signal input circuit
• CAN communication signal between ECM
and IPDM E/R
NO
• Harness or connector between IPDM E/R
and cooling fan relay
• Harness or connector between IPDM E/R
and cooling fan control module.
• Harness or connector between cooling fan
control module and cooling fan motor
• Cooling fan motor
• Cooling fan relay
• Cooling fan control module
• IPDM E/R
Symptom
Inspection contents
Possible cause
Diagnosis mode
Description
Ecu Identification
Allows confirmation of IPDM E/R part number.
Self Diagnostic Result
Displays the diagnosis results judged by IPDM E/R.
Data Monitor
Displays the real-time input/output data from IPDM E/R input/output data.
Active Test
IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor
The results of transmit/receive diagnosis of CAN communication can be read.
Monitor Item
[Unit]
MAIN SIG-
NALS
Description
RAD FAN REQ
[%]
×
Displays the value of the cooling fan speed request signal received from ECM via
CAN communication.
AC COMP REQ
[Off/On]
×
Displays the status of the A/C compressor request signal received from ECM via
CAN communication.
TAIL&CLR REQ
[Off/On]
×
Displays the status of the position light request signal received from BCM via CAN
communication.
HL LO REQ
[Off/On]
×
Displays the status of the low beam request signal received from BCM via CAN
communication.
HL HI REQ
[Off/On]
×
Displays the status of the high beam request signal received from BCM via CAN
communication.
FR FOG REQ
[Off/On]
×
Displays the status of the front fog light request signal received from BCM via
CAN communication.
FR WIP REQ
[Stop/1LOW/Low/Hi]
×
Displays the status of the front wiper request signal received from BCM via CAN
communication.
WIP AUTO STOP
[STOP P/ACT P]
×
Displays the status of the front wiper auto stop signal judged by IPDM E/R.
WIP PROT
[Off/BLOCK]
×
Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
IGN RLY
[Off/On]
×
Displays the status of the ignition relay judged by IPDM E/R.
Revision: 2013 October
2014 JUKE
PCS-46
< SYSTEM DESCRIPTION >
[IPDM E/R (WITHOUT I-KEY)]
DIAGNOSIS SYSTEM (IPDM E/R)
ACTIVE TEST
Test item
INTER/NP SW
[Off/On]
Displays the status of the shift position (CVT models) judged by IPDM E/R.
ST RLY REQ
[Off/On]
Displays the status of the starter relay status signal received from BCM via CAN
communication.
DTRL REQ
[Off/On]
Displays the status of the daytime running light request signal received from BCM
via CAN communication.
OIL P SW
[Open/Close]
NOTE:
This item is indicated, but not monitored.
HOOD SW
[Off/On]
NOTE:
This item is indicated, but not monitored.
HL WASHER REQ
[Off/On]
NOTE:
This item is indicated, but not monitored.
THFT HRN REQ
[Off/On]
Displays the status of the theft warning horn request signal received from BCM
via CAN communication.
HORN CHIRP
[Off/On]
Displays the status of the horn reminder request signal received from BCM via
CAN communication.
Monitor Item
[Unit]
MAIN SIG-
NALS
Description
Test item
Operation
Description
HORN
On
Operates horn relay for 20 ms.
REAR DEFOGGER
Off
OFF
On
Operates the rear window defogger relay.
FRONT WIPER
Off
OFF
Lo
Operates the front wiper relay.
Hi
Operates the front wiper relay and front wiper high relay.
MOTOR FAN
1
OFF
2
Transmits 50% pulse duty signal (PWM signal) to the cooling fan control module.
3
Transmits 75% pulse duty signal (PWM signal) to the cooling fan control module.
4
Transmits 100% pulse duty signal (PWM signal) to the cooling fan control module.
HEAD LAMP WASHER
On
NOTE:
This item is indicated, but cannot be tested.
EXTERNAL LAMPS
Off
OFF
TAIL
Operates the tail lamp relay.
Lo
Operates the headlamp low relay.
Hi
Operates the headlamp low relay and ON/OFF the headlamp high relay at 1 second
intervals.
Fog
Operates the front fog lamp relay.
Revision: 2013 October
2014 JUKE
PCS
IPDM E/R
PCS-47
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R (WITHOUT I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ECU DIAGNOSIS INFORMATION
IPDM E/R
Reference Value
INFOID:0000000009751948
VALUES ON THE DIAGNOSIS TOOL
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor Item
Condition
Value/Status
RAD FAN REQ
Engine idle speed
Changes depending on engine
coolant temperature, air conditioner
operation status, vehicle speed,
etc.
0 – 100%
AC COMP REQ
Engine running
A/C switch OFF
Off
A/C switch ON
(Compressor is operating)
On
TAIL&CLR REQ
Lighting switch OFF
Off
• Lighting switch 1ST or 2ND (Light is illuminated)
• Daytime running light system operated
On
HL LO REQ
Lighting switch OFF
Off
Lighting switch 2ND (Light is illuminated)
On
HL HI REQ
Lighting switch 2ND (light is illumi-
nated)
Lighting switch other than HI and
PASS
Off
Lighting switch HI or PASS
On
FR FOG REQ
Lighting switch 1ST or 2ND
(Light is illuminated)
Front fog lamp switch OFF
Off
Front fog lamp switch ON
On
FR WIP REQ
Ignition switch ON
Front wiper switch OFF
Stop
Front wiper switch INT
1LOW
Front wiper switch LO
Low
Front wiper switch HI
Hi
WIP AUTO STOP
Ignition switch ON
Front wiper stop position
STOP P
Any position other than front wiper
stop position
ACT P
WIP PROT
Ignition switch ON
Front wiper operates normally.
Off
Front wiper stops at fail-safe opera-
tion.
BLOCK
IGN RLY
Ignition switch OFF or ACC
Off
Ignition switch ON
On
INTER/NP SW
Ignition switch ON (CVT models)
Selector lever in any position other
than P or N
Off
Selector lever in P or N position
On
Ignition switch OFF or ACC (M/T models)
Off
Ignition switch ON (M/T models)
On
ST RLY REQ
Ignition switch OFF or ACC
Off
Ignition switch ON
On
Revision: 2013 October
2014 JUKE
PCS-48
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R (WITHOUT I-KEY)]
IPDM E/R
TERMINAL LAYOUT
PHYSICAL VALUES
DTRL REQ
Daytime running light system is not operated with ignition switch OFF
Off
Any of the condition below
• Daytime running light system is operated
• Light switch 2ND (light is illuminated)
On
OIL P SW
NOTE:
This item is indicated, but not monitored
Open
HOOD SW
NOTE:
This item is indicated, but not monitored
Off
HL WASHER REQ
NOTE:
This item is indicated, but not monitored
Off
THFT HRN REQ
Not operation
Off
Theft warning alarm is activated
On
HORN CHIRP
Not operation
Off
Horn reminder is activated
On
Monitor Item
Condition
Value/Status
JPMIA1512ZZ
Terminal NO.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output
+
–
1
(R)
Ground
Battery power supply
Input
Ignition switch OFF
6 – 16 V
2
(G)
Ground
Battery power supply
Input
Ignition switch OFF
6 – 16 V
Revision: 2013 October
2014 JUKE
PCS
IPDM E/R
PCS-49
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R (WITHOUT I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
3
(R)
Ground
Starter motor
Output
Other than engine cranking
0 – 1 V
At engine cranking
6 – 16 V
4
(P)
Ground
Battery power supply
Input
Ignition switch OFF
9 – 16 V
6
(GR)
Ground
Ignition switch START
Output
Any position other ignition switch START
0 – 1 V
Ignition switch START
6 – 16 V
9
(B/Y)
Ground
Ground
—
Ignition switch ON
0 – 1 V
14
(R)
Ground
Rear window defogger
Output
Ignition
switch
ON
Rear window defogger switch
OFF
0 – 1 V
Rear window defogger switch
ON
9 – 16 V
18
(B/Y)
Ground
Ground
—
Ignition switch ON
0 – 1 V
19
(W)
Ground
Front fog lamp (RH)
Output
Lighting
switch
1ST or
2ND
Front fog lamp switch OFF
0 – 1 V
Front fog lamp switch ON
9 – 16 V
20
(V)
Ground
Front fog lamp (LH)
Output
Lighting
switch
1ST or
2ND
Front fog lamp switch OFF
0 – 1 V
Front fog lamp switch ON
9 – 16 V
22
(G)
Ground
Ignition switch
Output
Ignition switch OFF or ACC
0 – 1 V
Ignition switch ON
6 – 16 V
23
(SB)
Ground
Cranking request
Output
Ignition switch OFF
0 – 1 V
Ignition
switch
ON
Select lever P or N
Select lever in any position oth-
er than P or N
9 – 16 V
Engine running
25
(BR)
Ground
Front wiper stop posi-
tion
Input
Ignition
switch
ON
Front wiper stop position
0 – 1.5 V
Any position other than front
wiper stop position
9 – 16 V
26
(P)
Ground
CAN-L
Input/
Output
—
—
27
(L)
Ground
CAN-H
Input/
Output
—
—
28
(Y)
Ground
Daytime running light
relay control
Output
Daytime running light deactivated
0 – 1 V
Daytime running light activated
9 – 16 V
30
(V)
Ground
Starter relay control
Output
At engine cranking
0 – 1 V
Other than engine cranking
6 – 16 V
31
(Y)
Ground
Fuel pump relay con-
trol
Output
• Approximately 1 second after turning the
ignition switch ON
• Engine running
0 – 1 V
Approximately 1 second or more after turn-
ing the ignition switch ON
6 – 16 V
Terminal NO.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output
+
–
Revision: 2013 October
2014 JUKE
PCS-50
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R (WITHOUT I-KEY)]
IPDM E/R
33
(G)
Ground
Power generation
command signal
Output
Ignition switch ON
6.3 V
40% is set on “ACTIVE TEST”, “ALTERNA-
TOR DUTY” of “ENGINE”
3.8 V
80% is set on “ACTIVE TEST”, “ALTERNA-
TOR DUTY” of “ENGINE”
1.4 V
34
(L)
Ground
Horn relay control
Output
The horn is deactivated
9 – 16 V
The horn is activated
0 – 1 V
35
(G)
Ground
ECM relay power sup-
ply
Output
Ignition switch OFF
(More than a few seconds after turning igni-
tion switch OFF)
0 – 1 V
• Ignition switch ON
• Ignition switch OFF
(For a few seconds after turning ignition
switch OFF)
6 – 16 V
36
(P)
Ground
ECM relay power sup-
ply
Output
Ignition switch OFF
(More than a few seconds after turning igni-
tion switch OFF)
0 – 1 V
• Ignition switch ON
• Ignition switch OFF
(For a few seconds after turning ignition
switch OFF)
6 – 16 V
39
(L)
Ground
Front wiper HI
Output
Ignition
switch
ON
Front wiper switch OFF
0 – 1 V
Front wiper switch HI
9 – 16 V
41
(BR)
Ground
ECM relay control
Output
Ignition switch OFF
(More than a few seconds after turning igni-
tion switch OFF)
6 – 16 V
• Ignition switch ON
• Ignition switch OFF
(For a few seconds after turning ignition
switch OFF)
0 – 1 V
42
(Y)
Ground
ECM power supply
Output
Ignition switch OFF
6 – 16 V
Terminal NO.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output
+
–
JPMIA0001GB
JPMIA0002GB
JPMIA0003GB
Revision: 2013 October
2014 JUKE
PCS
IPDM E/R
PCS-51
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R (WITHOUT I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
43
(L)
Ground
Parking lamp and side
marker lamp
Output
Lighting switch OFF
0 – 1 V
Lighting switch 1ST
9 – 16 V
44
(R)
Ground
Rear combination
lamp and illumination
Output
Lighting switch OFF
0 – 1 V
Lighting switch 1ST
9 – 16 V
45
(W)
Ground
Front wiper LO
Output
Ignition
switch
ON
Front wiper switch OFF
0 – 1 V
Front wiper switch LO
9 – 16 V
48
(BR)
Ground
Transmission range
switch
*1
Input
Select lever in any position other than P or
N (Ignition switch ON)
0 – 1 V
Select lever P or N (Ignition switch ON)
9 – 16 V
Clutch interlock
switch
*2
Release the clutch pedal
0 – 1 V
Depress the clutch pedal
9 – 16 V
49
(Y)
Ground
Headlamp HI (RH)
Output
Ignition
switch
2ND
Lighting switch OFF
0 – 1 V
• Lighting switch HI
• Lighting switch PASS
9 – 16 V
50
(G)
Ground
Headlamp HI (LH)
Output
Ignition
switch
2ND
Lighting switch OFF
0 – 1 V
• Lighting switch HI
• Lighting switch PASS
9 – 16 V
51
(L)
Ground
Headlamp LO (LH)
Output
Lighting switch OFF
0 – 1 V
Lighting switch 2ND
9 – 16 V
52
(P)
Ground
Headlamp LO (RH)
and daytime running
light relay 1
Output
Lighting switch OFF
0 – 1 V
Lighting switch 2ND
9 – 16 V
54
(P)
Ground
Fuel pump power sup-
ply
Output
Approximately 1 second or more than after
turning the ignition switch ON
0 – 1 V
• Approximately 1 second after turning the
ignition switch ON
• Engine running
6 – 16 V
55
(G)
Ground
Throttle control motor
relay power supply
Output
Ignition switch OFF
(More than a few seconds after turning igni-
tion switch OFF)
0 – 1 V
• Ignition switch ON
• Ignition switch OFF
(For a few seconds after turning ignition
switch OFF)
6 – 16 V
56
(SB)
Ground
A/C relay power supply
Output
Engine
running
A/C switch OFF
0 – 1 V
A/C switch ON
(A/C compressor is operating)
9 – 16 V
57
(O)
Ground
Ignition relay power
supply
Output
Ignition switch OFF or ACC
0 – 1 V
Ignition switch ON
6 – 16 V
58
(LG)
Ground
Ignition relay power
supply
Output
Ignition switch OFF
0 – 1 V
Ignition switch ON
6 – 16 V
59
(V)
Ground
Ignition relay power
supply
Output
Ignition switch OFF
0 – 1 V
Ignition switch ON
6 – 16 V
60
(SB)
Ground
Throttle control motor
relay control
Output
Ignition switch OFF or ACC
6 – 16 V
Ignition switch ON
0 – 1 V
61
(LG)
Ground
Ignition relay power
supply
Output
Ignition switch OFF
0 – 1 V
Ignition switch ON
6 – 16 V
Terminal NO.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output
+
–
Revision: 2013 October
2014 JUKE
PCS-52
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R (WITHOUT I-KEY)]
IPDM E/R
*
1
: CVT models
*
2
: M/T models
Fail-safe
INFOID:0000000009751949
CAN COMMUNICATION CONTROL
When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If No CAN Communication Is Available With ECM
If No CAN Communication Is Available With BCM
IGNITION RELAY MALFUNCTION DETECTION FUNCTION
• IPDM E/R monitors the voltage at the contact circuit and excitation coil circuit of the ignition relay inside it.
• IPDM E/R judges the ignition relay error if the voltage differs between the contact circuit and the excitation
coil circuit.
62
(O)
Ground
Ignition relay power
supply
Output
Ignition switch OFF
0 – 1 V
Ignition switch ON
6 – 16 V
67
(L)
Ground
Cooling fan relay con-
trol
Output
Ignition switch OFF or ACC
9 – 16 V
Ignition switch ON
0 – 1 V
69
(BR)
Ground
Ignition power supply
No. 2
Output
Ignition switch OFF or ACC
0 – 1 V
Ignition switch ON
6 – 16 V
72
(W)
Ground
Cooling fan control
Output
Engine idling
0 – 5 V
Terminal NO.
(Wire color)
Description
Condition
Value
(Approx.)
Signal name
Input/
Output
+
–
Control part
Fail-safe operation
Cooling fan
• Transmits the pulse duty signal (PWM signal) 100% when the ignition switch is turned ON.
• Transmits the pulse duty signal (PWM signal) 0% when the ignition switch is turned OFF.
A/C compressor
A/C relay OFF
Alternator
Outputs the power generation command signal (PWM signal) 0%
Control part
Fail-safe operation
Headlamp
• Turns ON the headlamp low relay when the ignition switch is turned ON
• Turns OFF the headlamp low relay when the ignition switch is turned OFF
• Headlamp high relay OFF
• Parking lamp
• License plate lamp
• Illumination
• Tail lamp
• Side marker lamp
• Turns ON the tail lamp relay when the ignition switch is turned ON
• Turns OFF the tail lamp relay when the ignition switch is turned OFF
Front wiper motor
• The status just before activation of fail-safe control is maintained until the ignition switch is turned OFF while
the front wiper is operating at LO or HI speed.
• The wiper is operated at LO speed until the ignition switch is turned OFF if the fail-safe control is activated
while the front wiper is set in the INT mode and the front wiper motor is operating.
• Returns automatically wiper to stop position when ignition switch is turned ON if fail-safe control is activated
while front wiper motor is operated and wiper stop in the other position than stop position.
• The status is held at service position if the fail-safe control is activated while the service position function is
operating.
Front fog lamp
Front fog lamp relay OFF
Rear window defogger
Rear window defogger relay OFF
Horn
Horn OFF
Starter motor
Starter control relay OFF
Revision: 2013 October
2014 JUKE
PCS
IPDM E/R
PCS-53
< ECU DIAGNOSIS INFORMATION >
[IPDM E/R (WITHOUT I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
• If the ignition relay cannot turn OFF due to contact seizure, it activates the tail lamp relay for 10 minutes to
alert the user to the ignition relay malfunction when the ignition switch is turned OFF.
FRONT WIPER PROTECTION FUNCTION
IPDM E/R detects front wiper stop position by a front wiper stop position signal.
When a front wiper stop position signal is in the conditions listed below, IPDM E/R stops power supply to wiper
after repeating a front wiper 10 seconds activation and 20 seconds stop.
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
STARTER MOTOR PROTECTION FUNCTION
IPDM E/R turns OFF the starter control relay to protect the starter motor when the starter control relay remains
active for 90 seconds.
DTC Index
INFOID:0000000009751950
NOTE:
• The details of time display are as follows.
- CRNT: A malfunction is detected now.
- PAST: A malfunction was detected in the past.
• IGN counter is displayed on FFD (Freeze Frame Data).
- The number is 0 when is detected now.
- The number increases like 1
→
2 ··· 38
→
39 after returning to the normal condition whenever IGN OFF
→
ON.
- The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
×
: Applicable
Voltage judgment
IPDM E/R judgment
Operation
Ignition relay contact
side
Ignition relay excitation
coil side
ON
ON
Ignition relay ON normal
—
OFF
OFF
Ignition relay OFF normal
—
ON
OFF
Ignition relay ON stuck
• Detects DTC “B2098: IGN RELAY ON”
• Turns ON the tail lamp relay for 10 minutes
OFF
ON
Ignition relay OFF stuck
Detects DTC “B2099: IGN RELAY OFF”
Ignition switch
Front wiper switch
Front wiper stop position signal
ON
OFF
The front wiper stop position signal (stop position) cannot be input for 10 seconds.
ON
The front wiper stop position signal does not change for 10 seconds.
CONSULT display
Fail-safe
Refer to
No DTC is detected.
further testing
may be required.
—
—
U1000: CAN COMM CIRCUIT
×
B2098: IGN RELAY ON
×
B2099: IGN RELAY OFF
—
B209F: STR CUT OFF OPEN
—
B20A0: STR CUT OFF SHORT
—
B210B: START CONT RLY ON
—
B210C: START CONT RLY OFF
—
B210D: STARTER RELAY ON
—
B210E: STARTER RELAY OFF
—
Revision: 2013 October
2014 JUKE
PCS-54
< WIRING DIAGRAM >
[IPDM E/R (WITHOUT I-KEY)]
IPDM E/R
WIRING DIAGRAM
IPDM E/R
Wiring Diagram
INFOID:0000000009751951
JRMWE7904GB
Revision: 2013 October
2014 JUKE
PCS
IPDM E/R
PCS-55
< WIRING DIAGRAM >
[IPDM E/R (WITHOUT I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
JRMWE7905GB
Revision: 2013 October
2014 JUKE
PCS-56
< WIRING DIAGRAM >
[IPDM E/R (WITHOUT I-KEY)]
IPDM E/R
JRMWE7906GB
Revision: 2013 October
2014 JUKE
PCS
IPDM E/R
PCS-57
< WIRING DIAGRAM >
[IPDM E/R (WITHOUT I-KEY)]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
JRMWE7907GB
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст