Nissan Juke (2014 year). Service Repair Manual — part 271
WW-14
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
NOTE:
*: Power position shifts to “LOCK” from “OFF”, when ignition switch is in the OFF position, selector lever is in the P position (A/T models
and CVT models), and any of the following conditions are met.
• Closing door
• Opening door
• Door is locked using door request switch
• Door is locked using Intelligent Key
The power position shifts to “ACC” when the push-button ignition switch (push switch) is pushed at “LOCK”.
WIPER
WIPER : CONSULT Function - WIPER
INFOID:0000000009754873
WORK SUPPORT
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power position is “LOCK”*.)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power position is “OFF”.)
LOCK>ACC
While turning power position from “LOCK”* *to “ACC”
ACC>ON
While turning power position from “ACC” to “IGN”
RUN>ACC
While turning power position from “RUN” to “ACC” (Vehicle is
stopping and selector lever is except P position.)
CRANK>RUN
While turning power position from “CRANKING” to “RUN” (From
cranking up the engine to run it)
RUN>URGENT
While turning power position from “RUN“ to “ACC” (Emergency
stop operation)
ACC>OFF
While turning power position from “ACC” to “OFF”
OFF>LOCK
While turning power position from “OFF” to “LOCK”*
OFF>ACC
While turning power position from “OFF” to “ACC”
ON>CRANK
While turning power position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power position is
“OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power position is
“LOCK”*.) to low power consumption mode
LOCK
Power position is “LOCK”*
OFF
Power position is “OFF” (Ignition switch OFF)
ACC
Power position is “ACC” (Ignition switch ACC)
ON
Power position is “IGN” (Ignition switch ON with engine stopped)
ENGINE RUN
Power position is “RUN” (Ignition switch ON with engine running)
CRANKING
Power position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
Revision: 2013 October
2014 JUKE
DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)
WW-15
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
*:Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
Service item
Setting item
Description
WIPER SPEED
SETTING
On
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
Off*
Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)
Monitor Item
[Unit]
Description
PUSH SW
[Off/On]
The switch status input from push-button ignition switch
VEH SPEED 1
[km/h]
Displays the value of the vehicle speed signal received from combination meter via CAN com-
munication
FR WIPER HI
[Off/On]
Status of each switch judged by BCM using the combination switch reading function
FR WIPER LOW
[Off/On]
FR WASHER SW
[Off/On]
FR WIPER INT
[Off/On]
FR WIPER STOP
[Off/On]
Displays the status of the front wiper stop position signal received from IPDM E/R via CAN
communication.
INT VOLUME
[1
−
7]
Status of each switch judged by BCM using the combination switch reading function
RR WIPER ON
[Off/On]
Status of each switch judged by BCM using the combination switch reading function
RR WIPER INT
[Off/On]
RR WASHER SW
[Off/On]
RR WIPER STOP
[Off/On]
Rear wiper motor (stop position) status input from the rear wiper motor
RAIN SENSOR
[Off/LOW/HIGH/SPLASH/NG]
NOTE:
This item is displayed, but cannot be monitored.
Test item
Operation
Description
FR WIPER
Hi
Transmits the front wiper request signal (HI) to IPDM E/R via CAN communication to op-
erate the front wiper HI operation.
Lo
Transmits the front wiper request signal (LO) to IPDM E/R via CAN communication to
operate the front wiper LO operation.
INT
Transmits the front wiper request signal (INT) to IPDM E/R via CAN communication to
operate the front wiper INT operation.
Off
Stops transmitting the front wiper request signal to stop the front wiper operation.
RR WIPER
On
Output the voltage to operate the rear wiper motor.
Off
Stops the voltage to stop the rear wiper motor.
Revision: 2013 October
2014 JUKE
WW-16
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
COMMON ITEM
COMMON ITEM : CONSULT Function (BCM - COMMON ITEM)
INFOID:0000000010296034
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
WIPER
WIPER : CONSULT Function (BCM - WIPER)
INFOID:0000000009754875
WORK SUPPORT
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp control
INT LAMP
×
×
×
Remote keyless entry system
MULTI REMOTE ENT
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
Air conditioning system
AIR CONDITONER
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NATS
IMMU
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
RAP system
RETAINED PWR
×
×
Signal buffer system
SIGNAL BUFFER
×
×
Panic alarm
PANIC ALARM
×
TPMS
AIR PRESSUE MONITOR
×
×
×
Revision: 2013 October
2014 JUKE
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
WW-17
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
*: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
Service item
Setting item
Description
WIPER SPEED
SETTING
On
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
Off*
Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)
Monitor Item
[Unit]
Description
IGN ON SW
[On/Off]
Ignition switch ON status judged from ignition power supply.
IGN SW CAN
[On/Off]
Ignition switch ON status received from IPDM E/R with CAN communication.
FR WIPER HI
[On/Off]
Each switch status that BCM judges from the combination switch reading function.
FR WIPER LOW
[On/Off]
FR WIPER INT
[On/Off]
FR WASHER SW
[On/Off]
INT VOLUME
[1
−
7]
Each switch status that BCM judges from the combination switch reading function.
FR WIPER STOP
[On/Off]
Front wiper motor (stop position) status received from IPDM E/R with CAN communication.
VEHICLE SPEED
[km/h]
The value of the vehicle speed signal received from combination meter with CAN communication.
RR WIPER ON
[On/Off]
Each switch status that BCM judges from the combination switch reading function.
RR WIPER INT
[On/Off]
RR WASHER SW
[On/Off]
RR WIPER STOP
[On/Off]
Rear wiper motor (stop position) status input from the rear wiper motor.
REVERSE SW CAN
[On/Off]
Reverse position status as judged from TCM with CAN communication.
RAIN SENSOR
[Off/LOW/HIGH/SPLASH/NG]
NOTE:
This item is displayed, but cannot be monitored.
Revision: 2013 October
2014 JUKE
WW-18
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)
Test item
Operation
Description
FR WIPER
Hi
Transmits the front wiper request signal (HI) to IPDM E/R with CAN communication to
operate the front wiper HI operation.
Lo
Transmits the front wiper request signal (LO) to IPDM E/R with CAN communication to
operate the front wiper LO operation.
INT
Transmits the front wiper request signal (INT) to IPDM E/R with CAN communication to
operate the front wiper INT operation.
Off
Stops transmitting the front wiper request signal to stop the front wiper operation.
RR WIPER
On
Outputs the voltage to operate the rear wiper motor.
Off
Stops the voltage to stop.
Revision: 2013 October
2014 JUKE
DIAGNOSIS SYSTEM (IPDM E/R)
WW-19
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
DIAGNOSIS SYSTEM (IPDM E/R)
WITH INTELLIGENT KEY
WITH INTELLIGENT KEY : Diagnosis Description
INFOID:0000000010296035
AUTO ACTIVE TEST
Description
In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Rear window defogger
• Front wiper motor
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
• Headlamp (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan
Operation Procedure
CAUTION:
Wiper arm interferes with hood when wiper is operated while wiper arm is in the raised position.
Always perform auto active test without setting wiper arm in the raised position. Always pour water on
front windshield glass in advance to auto active test so that damage on front windshield glass surface
is prevented.
1.
Turn the ignition switch OFF.
2.
Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
CAUTION:
Close passenger door.
3.
Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
CAUTION:
Engine starts when ignition switch is turned ON while brake pedal is depressed.
4.
After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
• When auto active test mode has to be cancelled halfway through test, turn the ignition switch OFF.
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to
Inspection in Auto Active Test Mode
When auto active test mode is actuated, the following operation sequence is repeated 3 times.
Operation
sequence
Inspection location
Operation
1
Rear window defogger
10 seconds
2
Front wiper motor
LO for 5 seconds
→
HI for 5 seconds
3
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
10 seconds
4
Headlamp
LO for 10 seconds
→
HI ON
⇔
OFF 5 times
5
A/C compressor (magnet clutch)
ON
⇔
OFF 5 times
6
Cooling fan
50% duty for 5 seconds
→
100% duty for 5 seconds
Revision: 2013 October
2014 JUKE
WW-20
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (IPDM E/R)
Concept of auto active test
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode
JMMIA0588GB
Symptom
Inspection contents
Possible cause
Rear window defogger does not operate
Perform auto active test.
Does the rear window defog-
ger operate?
YES
BCM signal input circuit
NO
• Rear window defogger
• Rear window defogger ground circuit
• Harness or connector between IPDM E/R
and rear window defogger
• IPDM E/R
Any of the following components do not
operate
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
• Headlamp (HI, LO)
• Front wiper motor
Perform auto active test.
Does the applicable system
operate?
YES
BCM signal input circuit
NO
• Lamp or motor
• Lamp or motor ground circuit
• Harness or connector between IPDM E/R
and applicable system
• IPDM E/R
A/C compressor does not operate
Perform auto active test.
Does the magnet clutch oper-
ate?
YES
• A/C amp. signal input circuit
• CAN communication signal between A/C
amp. and ECM
• CAN communication signal between ECM
and IPDM E/R
NO
• Magnet clutch
• Harness or connector between IPDM E/R
and magnet clutch
• IPDM E/R
Revision: 2013 October
2014 JUKE
DIAGNOSIS SYSTEM (IPDM E/R)
WW-21
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WITH INTELLIGENT KEY : CONSULT Function (IPDM E/R)
INFOID:0000000010296036
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
SELF DIAGNOSTIC RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Cooling fan does not operate
Perform auto active test.
Does the cooling fan operate?
YES
• ECM signal input circuit
• CAN communication signal between ECM
and IPDM E/R
NO
• Harness or connector between IPDM E/R
and cooling fan relay
• Harness or connector between IPDM E/R
and cooling fan control module.
• Harness or connector between cooling fan
control module and cooling fan motor
• Cooling fan motor
• Cooling fan relay
• Cooling fan control module
• IPDM E/R
Symptom
Inspection contents
Possible cause
Diagnosis mode
Description
Ecu Identification
Allows confirmation of IPDM E/R part number.
Self Diagnostic Result
Displays the diagnosis results judged by IPDM E/R.
Data Monitor
Displays the real-time input/output data from IPDM E/R input/output data.
Active Test
IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor
The results of transmit/receive diagnosis of CAN communication can be read.
Monitor Item
[Unit]
MAIN
SIGNALS
Description
RAD FAN REQ
[%]
×
Displays the value of the cooling fan speed request signal received from ECM via CAN
communication.
AC COMP REQ
[Off/On]
×
Displays the status of the A/C compressor request signal received from ECM via CAN
communication.
TAIL&CLR REQ
[Off/On]
×
Displays the status of the position light request signal received from BCM via CAN
communication.
HL LO REQ
[Off/On]
×
Displays the status of the low beam request signal received from BCM via CAN com-
munication.
HL HI REQ
[Off/On]
×
Displays the status of the high beam request signal received from BCM via CAN com-
munication.
FR FOG REQ
[Off/On]
×
Displays the status of the front fog light request signal received from BCM via CAN
communication.
FR WIP REQ
[Stop/1LOW/Low/Hi]
×
Displays the status of the front wiper request signal received from BCM via CAN com-
munication.
WIP AUTO STOP
[STOP P/ACT P]
×
Displays the status of the front wiper auto stop signal judged by IPDM E/R.
WIP PROT
[Off/BLOCK]
×
Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
IGN RLY1 -REQ
[Off/On]
Displays the status of the ignition switch ON signal received from BCM via CAN com-
munication.
Revision: 2013 October
2014 JUKE
WW-22
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (IPDM E/R)
ACTIVE TEST
Test item
IGN RLY
[Off/On]
×
Displays the status of the ignition relay judged by IPDM E/R.
PUSH SW
[Off/On]
Displays the status of the push-button ignition switch judged by IPDM E/R.
INTER/NP SW
[Off/On]
Displays the status of the ignition power supply (M/T models) or shift position (CVT
models) judged by IPDM E/R.
ST RLY CONT
[Off/On]
Displays the status of the starter relay status signal received from BCM via CAN com-
munication.
IHBT RLY -REQ
[Off/On]
Displays the status of the starter control relay signal received from BCM via CAN com-
munication.
ST/INHI RLY
[Off/ ST ON/INHI ON/UNKWN]
Displays the status of the starter relay and starter control relay judged by IPDM E/R.
DETENT SW
[Off/On]
Displays the status of the CVT shift selector (detention switch) judged by IPDM E/R.
S/L RLY -REQ
[Off/On]
NOTE:
This item is indicated, but not monitored.
S/L STATE
[LOCK/UNLK/UNKWN]
NOTE:
This item is indicated, but not monitored.
DTRL REQ
[Off/On]
Displays the status of the daytime running light request signal received from BCM via
CAN communication.
NOTE:
This item is monitored only for the except for NISMO models.
OIL P SW
[Open/Close]
NOTE:
This item is indicated, but not monitored.
HOOD SW
[Off/On]
NOTE:
This item is indicated, but not monitored.
HL WASHER REQ
[Off/On]
NOTE:
This item is indicated, but not monitored.
THFT HRN REQ
[Off/On]
Displays the status of the theft warning horn request signal received from BCM via
CAN communication.
HORN CHIRP
[Off/On]
Displays the status of the horn reminder request signal received from BCM via CAN
communication.
Monitor Item
[Unit]
MAIN
SIGNALS
Description
Test item
Operation
Description
HORN
On
Operates horn relay for 20 ms.
REAR DEFOGGER
Off
OFF
On
Operates the rear window defogger relay.
FRONT WIPER
Off
OFF
Lo
Operates the front wiper relay.
Hi
Operates the front wiper relay and front wiper high relay.
MOTOR FAN
1
OFF
2
Transmits 50% pulse duty signal (PWM signal) to the cooling fan control module.
3
Transmits 75% pulse duty signal (PWM signal) to the cooling fan control module.
4
Transmits 100% pulse duty signal (PWM signal) to the cooling fan control module.
HEAD LAMP WASHER
On
NOTE:
This item is indicated, but cannot be tested.
Revision: 2013 October
2014 JUKE
DIAGNOSIS SYSTEM (IPDM E/R)
WW-23
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WITHOUT INTELLIGENT KEY
WITHOUT INTELLIGENT KEY : Diagnosis Description
INFOID:0000000010296037
AUTO ACTIVE TEST
Description
In auto active test mode, the IPDM E/R sends a drive signal to the following systems to check their operation.
• Rear window defogger
• Front wiper motor
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
• Headlamp (LO, HI)
• A/C compressor (magnet clutch)
• Cooling fan
Operation Procedure
CAUTION:
Wiper arm interferes with hood when wiper is operated while wiper arm is in the raised position.
Always perform auto active test without setting wiper arm in the raised position. Always pour water on
front windshield glass in advance to auto active test so that damage on front windshield glass surface
is prevented.
1.
Turn the ignition switch OFF.
2.
Turn the ignition switch ON, and within 20 seconds, press the driver door switch 10 times. Then turn the
ignition switch OFF.
CAUTION:
Close passenger door.
3.
Turn the ignition switch ON within 10 seconds. After that the horn sounds once and the auto active test
starts.
CAUTION:
Engine starts when ignition switch is turned ON while brake pedal is depressed.
4.
After a series of the following operations is repeated 3 times, auto active test is completed.
NOTE:
• When auto active test mode has to be cancelled halfway through test, turn the ignition switch OFF.
• When auto active test is not activated, door switch may be the cause. Check door switch. Refer to
Inspection in Auto Active Test Mode
When auto active test mode is actuated, the following operation sequence is repeated 3 times.
EXTERNAL LAMPS
Off
OFF
TAIL
Operates the tail lamp relay.
Lo
Operates the headlamp low relay.
Hi
Operates the headlamp low relay and ON/OFF the headlamp high relay at 1 second
intervals.
Fog
Operates the front fog lamp relay.
Test item
Operation
Description
Operation
sequence
Inspection location
Operation
1
Rear window defogger
10 seconds
2
Front wiper motor
LO for 5 seconds
→
HI for 5 seconds
Revision: 2013 October
2014 JUKE
WW-24
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (IPDM E/R)
Concept of auto active test
• IPDM E/R starts the auto active test with the door switch signals transmitted by BCM via CAN communica-
tion. Therefore, the CAN communication line between IPDM E/R and BCM is considered normal if the auto
active test starts successfully.
• The auto active test facilitates troubleshooting if any systems controlled by IPDM E/R cannot be operated.
Diagnosis chart in auto active test mode
3
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
10 seconds
4
Headlamp
LO for 10 seconds
→
HI ON
⇔
OFF 5 times
5
A/C compressor (magnet clutch)
ON
⇔
OFF 5 times
6
Cooling fan
50% duty for 5 seconds
→
100% duty for 5 seconds
Operation
sequence
Inspection location
Operation
JMMIA0588GB
Symptom
Inspection contents
Possible cause
Rear window defogger does not operate
Perform auto active test.
Does the rear window defog-
ger operate?
YES
BCM signal input circuit
NO
• Rear window defogger
• Rear window defogger ground circuit
• Harness or connector between IPDM E/R
and rear window defogger
• IPDM E/R
Any of the following components do not
operate
• Parking lamp
• License plate lamp
• Tail lamp
• Side marker lamp
• Front fog lamp
• Headlamp (HI, LO)
• Front wiper motor
Perform auto active test.
Does the applicable system
operate?
YES
BCM signal input circuit
NO
• Lamp or motor
• Lamp or motor ground circuit
• Harness or connector between IPDM E/R
and applicable system
• IPDM E/R
Revision: 2013 October
2014 JUKE
DIAGNOSIS SYSTEM (IPDM E/R)
WW-25
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WITHOUT INTELLIGENT KEY : CONSULT Function (IPDM E/R)
INFOID:0000000010296038
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with IPDM E/R.
SELF DIAGNOSTIC RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
A/C compressor does not operate
Perform auto active test.
Does the magnet clutch oper-
ate?
YES
• A/C amp. signal input circuit
• CAN communication signal between A/C
amp. and ECM
• CAN communication signal between ECM
and IPDM E/R
NO
• Magnet clutch
• Harness or connector between IPDM E/R
and magnet clutch
• IPDM E/R
Cooling fan does not operate
Perform auto active test.
Does the cooling fan operate?
YES
• ECM signal input circuit
• CAN communication signal between ECM
and IPDM E/R
NO
• Harness or connector between IPDM E/R
and cooling fan relay
• Harness or connector between IPDM E/R
and cooling fan control module.
• Harness or connector between cooling fan
control module and cooling fan motor
• Cooling fan motor
• Cooling fan relay
• Cooling fan control module
• IPDM E/R
Symptom
Inspection contents
Possible cause
Diagnosis mode
Description
Ecu Identification
Allows confirmation of IPDM E/R part number.
Self Diagnostic Result
Displays the diagnosis results judged by IPDM E/R.
Data Monitor
Displays the real-time input/output data from IPDM E/R input/output data.
Active Test
IPDM E/R can provide a drive signal to electronic components to check their operations.
CAN Diag Support Monitor
The results of transmit/receive diagnosis of CAN communication can be read.
Monitor Item
[Unit]
MAIN SIG-
NALS
Description
RAD FAN REQ
[%]
×
Displays the value of the cooling fan speed request signal received from ECM via
CAN communication.
AC COMP REQ
[Off/On]
×
Displays the status of the A/C compressor request signal received from ECM via
CAN communication.
TAIL&CLR REQ
[Off/On]
×
Displays the status of the position light request signal received from BCM via CAN
communication.
HL LO REQ
[Off/On]
×
Displays the status of the low beam request signal received from BCM via CAN
communication.
HL HI REQ
[Off/On]
×
Displays the status of the high beam request signal received from BCM via CAN
communication.
Revision: 2013 October
2014 JUKE
WW-26
< SYSTEM DESCRIPTION >
DIAGNOSIS SYSTEM (IPDM E/R)
ACTIVE TEST
Test item
FR FOG REQ
[Off/On]
×
Displays the status of the front fog light request signal received from BCM via
CAN communication.
FR WIP REQ
[Stop/1LOW/Low/Hi]
×
Displays the status of the front wiper request signal received from BCM via CAN
communication.
WIP AUTO STOP
[STOP P/ACT P]
×
Displays the status of the front wiper auto stop signal judged by IPDM E/R.
WIP PROT
[Off/BLOCK]
×
Displays the status of the front wiper fail-safe operation judged by IPDM E/R.
IGN RLY
[Off/On]
×
Displays the status of the ignition relay judged by IPDM E/R.
INTER/NP SW
[Off/On]
Displays the status of the shift position (CVT models) judged by IPDM E/R.
ST RLY REQ
[Off/On]
Displays the status of the starter relay status signal received from BCM via CAN
communication.
DTRL REQ
[Off/On]
Displays the status of the daytime running light request signal received from BCM
via CAN communication.
OIL P SW
[Open/Close]
NOTE:
This item is indicated, but not monitored.
HOOD SW
[Off/On]
NOTE:
This item is indicated, but not monitored.
HL WASHER REQ
[Off/On]
NOTE:
This item is indicated, but not monitored.
THFT HRN REQ
[Off/On]
Displays the status of the theft warning horn request signal received from BCM
via CAN communication.
HORN CHIRP
[Off/On]
Displays the status of the horn reminder request signal received from BCM via
CAN communication.
Monitor Item
[Unit]
MAIN SIG-
NALS
Description
Test item
Operation
Description
HORN
On
Operates horn relay for 20 ms.
REAR DEFOGGER
Off
OFF
On
Operates the rear window defogger relay.
FRONT WIPER
Off
OFF
Lo
Operates the front wiper relay.
Hi
Operates the front wiper relay and front wiper high relay.
MOTOR FAN
1
OFF
2
Transmits 50% pulse duty signal (PWM signal) to the cooling fan control module.
3
Transmits 75% pulse duty signal (PWM signal) to the cooling fan control module.
4
Transmits 100% pulse duty signal (PWM signal) to the cooling fan control module.
HEAD LAMP WASHER
On
NOTE:
This item is indicated, but cannot be tested.
EXTERNAL LAMPS
Off
OFF
TAIL
Operates the tail lamp relay.
Lo
Operates the headlamp low relay.
Hi
Operates the headlamp low relay and ON/OFF the headlamp high relay at 1 second
intervals.
Fog
Operates the front fog lamp relay.
Revision: 2013 October
2014 JUKE
BCM, IPDM E/R
WW-27
< ECU DIAGNOSIS INFORMATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
ECU DIAGNOSIS INFORMATION
BCM, IPDM E/R
List of ECU Reference
INFOID:0000000009754880
ECU
Reference
BCM
(With Intelligent Key system)
BCS-58, "DTC Inspection Priority Chart"
(Without Intelligent Key system)
BCS-132, "DTC Inspection Priority Chart"
IPDM E/R
(With Intelligent Key system)
(Without Intelligent Key system)
Revision: 2013 October
2014 JUKE
WW-28
< WIRING DIAGRAM >
WIPER AND WASHER SYSTEM
WIRING DIAGRAM
WIPER AND WASHER SYSTEM
Wiring Diagram - WIPER AND WASHER SYSTEM -
INFOID:0000000009754881
JRLWD0881GB
Revision: 2013 October
2014 JUKE
WIPER AND WASHER SYSTEM
WW-29
< WIRING DIAGRAM >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
JRLWD0882GB
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст