Nissan Juke (2014 year). Service Repair Manual — part 27
COMPONENT PARTS
BRC-13
< SYSTEM DESCRIPTION >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
Reservoir
Temporarily reserves the brake fluid drained from brake caliper, so that pressure efficiently decreases when
decreasing pressure of brake caliper.
Stop Lamp Switch
INFOID:0000000009752887
Detects the operation status of brake pedal and transmits converted electric signal to ABS actuator and elec-
tric unit (control unit).
Brake Pedal Position Switch
INFOID:0000000009752888
Detects the operation status of brake pedal and transmits converted electric signal to ABS actuator and elec-
tric unit (control unit).
Steering Angle Sensor
INFOID:0000000009752889
Detects the following information and transmits steering angle signal to ABS actuator and electric unit (control
unit) via CAN communication.
• Steering wheel rotation amount
• Steering wheel rotation angular velocity
• Steering wheel rotation direction
Yaw Rate/Side/Decel G Sensor
INFOID:0000000009752890
Calculates the following information that affects the vehicle, and transmits a signal to ABS actuator and elec-
tric unit (control unit) via communication lines.
• Vehicle rotation angular velocity (yaw rate signal)
• Vehicle lateral acceleration (side G signal) and longitudinal acceleration (decel G signal)
VDC OFF Switch
INFOID:0000000009752891
• This is an integrated switch with switches for other functions.
• Non-operational status or standby status of the following functions can be selected using VDC OFF switch.
VDC OFF indicator lamp indicates the operation status of function. (ON: Non-operational status, OFF:
Standby status)
- VDC function
NOTE:
Brake limited slip differential (BLSD) function control operates.
- TCS function
• VDC OFF indicator lamp turns OFF (standby status) when the engine is started again after it is stopped once
while VDC OFF indicator lamp is ON (non-operational status).
Brake Fluid Level Switch
INFOID:0000000009752892
Detects the brake fluid level in reservoir tank and transmits converted electric signal from combination meter to
ABS actuator and electric unit (control unit) via CAN communication, when brake fluid level is the specified
level or less.
Parking Brake Switch
INFOID:0000000009752893
Detects the operation status of parking brake switch and transmits converted electric signal from combination
meter to ABS actuator and electric unit (control unit).
Revision: 2013 October
2014 JUKE
BRC-14
< SYSTEM DESCRIPTION >
[WITH VDC]
SYSTEM
SYSTEM
System Description
INFOID:0000000009752894
• The system switches fluid pressure of each brake caliper to increase, to hold or to decrease according to
signals from control unit in ABS actuator and electric unit (control unit). This control system is applied to
VDC function, TCS function, ABS function, EBD function and brake limited slip differential (BLSD) function.
• Fail-safe function is available for each function and is activated by each function when system malfunction
occurs.
SYSTEM DIAGRAM
NOTE:
• TCM is CVT models only.
• AWD control module is AWD models only.
INPUT SIGNAL AND OUTPUT SIGNAL
Major signal transmission between each unit via communication lines is shown in the following table.
JSFIA0645GB
Revision: 2013 October
2014 JUKE
SYSTEM
BRC-15
< SYSTEM DESCRIPTION >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
VDC function, TCS function, ABS function, EBD function, Brake limited slip differential (BLSD) function
*1: Communication line between yaw rate/side/decel G sensor and ABS actuator and electric unit (control unit)
*2: Models with CVT
*3: AWD models
VALVE OPERATION [VDC FUNCTION, TCS FUNCTION AND BRAKE LIMITED SLIP DIFFEREN-
TIAL (BLSD) FUNCTION
The control unit built in the ABS actuator and electric unit (control unit) controls fluid pressure of the brake cal-
ipers, respectively, by operating each valve.
When VDC Function, TSC Function and Brake Limited Slip Differential (BLSD) Function is in Operation (During Pres-
Component
Signal description
Steering angle sensor
Mainly transmits the following signals to ABS actuator and electric unit (control unit) via CAN
communication.
• Steering angle sensor signal
Yaw rate/side/decel G sensor
Mainly transmits the following signals to ABS actuator and electric unit (control unit) via com-
munication line
*1
• Yaw rate signal
• Side G sensor signal
• Decel G sensor signal
ECM
Mainly transmits the following signals to ABS actuator and electric unit (control unit) via CAN
communication.
• Accelerator pedal position signal
• Engine speed signal
Mainly receives the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
• Target throttle position signal
TCM
*2
Mainly transmits the following signals to ABS actuator and electric unit (control unit) via CAN
communication.
• N range signal
• P range signal
• R range signal
• Current gear position signal
AWD control module
*3
Mainly transmits the following signals to ABS actuator and electric unit (control unit) via CAN
communication.
• Current AWD mode signal
Combination meter
Mainly transmits the following signals to ABS actuator and electric unit (control unit) via CAN
communication.
• Brake fluid level switch signal
Mainly receives the following signals from ABS actuator and electric unit (control unit) via CAN
communication.
• ABS warning lamp signal
• Brake warning lamp signal
• VDC warning lamp signal
• VDC OFF indicator lamp signal
Revision: 2013 October
2014 JUKE
BRC-16
< SYSTEM DESCRIPTION >
[WITH VDC]
SYSTEM
sure Increases)
During pressure front RH brake caliper increases
• Brake fluid is conveyed to the pump from the master cylinder through suction valve 2 and is pressurized by
the pump operation. The pressurized brake fluid is supplied to the front RH brake caliper through the ABS IN
valve. For the left caliper, brake fluid pressure is maintained because the pressurization is unnecessary. The
pressurization for the left caliper is controlled separately from the right caliper.
During pressure front LH brake caliper increases
• Brake fluid is conveyed to the pump from the master cylinder through suction valve 1 and is pressurized by
the pump operation. The pressurized brake fluid is supplied to the front LH brake caliper through the ABS IN
valve. For the right caliper, brake fluid pressure is maintained because the pressurization is unnecessary.
The pressurization for the right caliper is controlled separately from the left caliper.
During pressure rear RH brake caliper increases
• Brake fluid is conveyed to the pump from the master cylinder through suction valve 1 and is pressurized by
the pump operation. The pressurized brake fluid is supplied to the rear RH brake caliper through the ABS IN
valve. For the left caliper, brake fluid pressure is maintained because the pressurization is unnecessary. The
pressurization for the left caliper is controlled separately from the right caliper.
During pressure rear LH brake caliper increases
• Brake fluid is conveyed to the pump from the master cylinder through suction valve 2 and is pressurized by
the pump operation. The pressurized brake fluid is supplied to the rear LH brake caliper through the ABS IN
JSFIA0646GB
Name
Not activated
During pressure increases
Cut valve 1
Power supply is not supplied (open)
Power supply is supplied (close)
Cut valve 2
Power supply is not supplied (open)
Power supply is supplied (close)
Suction valve 1
Power supply is not supplied (close)
Power supply is supplied (open)
Suction valve 2
Power supply is not supplied (close)
Power supply is supplied (open)
ABS IN valve
Power supply is not supplied (open)
Power supply is not supplied (open)
ABS OUT valve
Power supply is not supplied (close)
Power supply is not supplied (close)
Each brake caliper (fluid pressure)
—
Pressure increases
Revision: 2013 October
2014 JUKE
SYSTEM
BRC-17
< SYSTEM DESCRIPTION >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
valve. For the right caliper, brake fluid pressure is maintained because the pressurization is unnecessary.
The pressurization for the right caliper is controlled separately from the left caliper.
When VDC Function, TSC Function and Brake Limited Slip Differential (BLSD) Function is Starts Operating (During
Pressure Holds)
During pressure front RH brake caliper holds
• Since the cut valve 2 and the suction valve 2 are closed, the front RH brake caliper, master cylinder, and res-
ervoir are blocked. This maintains fluid pressure applied on the front RH brake caliper. The pressurization for
the left caliper is controlled separately from the right caliper.
During pressure front LH brake caliper holds
• Since the cut valve 1 and the suction valve 1 are closed, the front LH brake caliper, master cylinder, and res-
ervoir are blocked. This maintains fluid pressure applied on the front LH brake caliper. The pressurization for
the right caliper is controlled separately from the left caliper.
During pressure rear RH brake caliper holds
• Since the cut valve 1 and the suction valve 1 are closed, the rear RH brake caliper, master cylinder, and res-
ervoir are blocked. This maintains fluid pressure applied on the rear RH brake caliper. The pressurization for
the left caliper is controlled separately from the right caliper.
During pressure rear LH brake caliper holds
JSFIA0647GB
Name
Not activated
During pressure holds
Cut valve 1
Power supply is not supplied (open)
Power supply is supplied (close)
Cut valve 2
Power supply is not supplied (open)
Power supply is supplied (close)
Suction valve 1
Power supply is not supplied (close)
Power supply is not supplied (close)
Suction valve 2
Power supply is not supplied (close)
Power supply is not supplied (close)
ABS IN valve
Power supply is not supplied (open)
Power supply is not supplied (open)
ABS OUT valve
Power supply is not supplied (close)
Power supply is not supplied (close)
Each brake caliper (fluid pressure)
—
Pressure holds
Revision: 2013 October
2014 JUKE
BRC-18
< SYSTEM DESCRIPTION >
[WITH VDC]
SYSTEM
• Since the cut valve 2 and the suction valve 2 are closed, the rear LH brake caliper, master cylinder, and res-
ervoir are blocked. This maintains fluid pressure applied on the rear LH brake caliper. The pressurization for
the right caliper is controlled separately from the left caliper.
When VDC Function, TSC Function and Brake Limited Slip Differential (BLSD) Function is in Operation (During Pres-
sure Decreases)
During pressure front RH brake caliper decreases
• Since the suction valve 2 and the ABS OUT valve close and the cut valve 2 and the ABS IN valve open, the
fluid pressure applied on the front RH brake caliper is reduced by supplying the fluid pressure to the master
cylinder via the ABS IN valve and the cut valve 2. The pressurization for the right caliper is controlled sepa-
rately from the left caliper.
During pressure front LH brake caliper decreases
• Since the suction valve 1 and the ABS OUT valve close and the cut valve 1 and the ABS IN valve open, the
fluid pressure applied on the front LH brake caliper is reduced by supplying the fluid pressure to the master
cylinder via the ABS IN valve and the cut valve 2. The pressurization for the left caliper is controlled sepa-
rately from the right caliper.
During pressure rear RH brake caliper decreases
• Since the suction valve 1 and the ABS OUT valve close and the cut valve 1 and the ABS IN valve open, the
fluid pressure applied on the rear RH brake caliper is reduced by supplying the fluid pressure to the master
cylinder via the ABS IN valve and the cut valve 2. The pressurization for the right caliper is controlled sepa-
rately from the left caliper.
JSFIA0648GB
Name
Not activated
During pressure decreases
Cut valve 1
Power supply is not supplied (open)
Power supply is not supplied (open)
Cut valve 2
Power supply is not supplied (open)
Power supply is not supplied (open)
Suction valve 1
Power supply is not supplied (close)
Power supply is not supplied (close)
Suction valve 2
Power supply is not supplied (close)
Power supply is not supplied (close)
ABS IN valve
Power supply is not supplied (open)
Power supply is not supplied (open)
ABS OUT valve
Power supply is not supplied (close)
Power supply is not supplied (close)
Each brake caliper (fluid pressure)
—
Pressure decreases
Revision: 2013 October
2014 JUKE
SYSTEM
BRC-19
< SYSTEM DESCRIPTION >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
During pressure rear LH brake caliper decreases
• Since the suction valve 2 and the ABS OUT valve close and the cut valve 2 and the ABS IN valve open, the
fluid pressure applied on the rear LH brake caliper is reduced by supplying the fluid pressure to the master
cylinder via the ABS IN valve and the cut valve 2. The pressurization for the left caliper is controlled sepa-
rately from the right caliper.
Component Parts and Function
VALVE OPERATION (ABS FUNCTION AND EBD FUNCTION)
The control unit built in the ABS actuator and electric unit (control unit) controls fluid pressure of the brake cal-
ipers, respectively, by operating each valve.
When Brake Pedal is Applied or ABS Function is in Operation (During Pressure Increases)
Component
Function
Pump
Returns the brake fluid reserved in reservoir to master cylinder by reducing pressure.
Motor
Activates the pump according to signals from ABS actuator and electric unit (control unit).
Cut valve 1
Cut valve 2
Shuts off the ordinary brake line from master cylinder.
Suction valve 1
Suction valve 2
Supplies the brake fluid from master cylinder to the pump.
ABS IN valve
Switches the fluid pressure line to increase or hold according to signals from control unit.
ABS OUT valve
Switches the fluid pressure line to increase, hold or decrease according to signals from control unit.
Inlet valve
Brake fluid sucked from the reservoir by the pump does not backflow.
Outlet valve
Brake fluid discharged from the pump does not backflow.
Return check valve
Returns the brake fluid from brake caliper and wheel cylinder to master cylinder by bypassing orifice
of each valve when brake is released.
Reservoir
Temporarily reserves the brake fluid drained from brake caliper, so that pressure efficiently decreas-
es when decreasing pressure of brake caliper and wheel cylinder.
JSFIA0649GB
Name
Not activated
During pressure increases
Cut valve 1
Power supply is not supplied (open)
Power supply is not supplied (open)
Cut valve 2
Power supply is not supplied (open)
Power supply is not supplied (open)
Revision: 2013 October
2014 JUKE
BRC-20
< SYSTEM DESCRIPTION >
[WITH VDC]
SYSTEM
During pressure front RH brake caliper increases
• When the cut valve 2 and the ABS IN valve opens, brake fluid is supplied to the front RH brake caliper from
the master cylinder through the ABS IN valve. Brake fluid does not flow into the reservoir because the ABS
OUT valve is closed.
During pressure front LH brake caliper increases
• When the cut valve 1 and the ABS IN valve opens, brake fluid is supplied to the front LH brake caliper from
the master cylinder through the ABS IN valve. Brake fluid does not flow into the reservoir because the ABS
OUT valve is closed.
During pressure rear RH brake caliper increases
• When the cut valve 1 and the ABS IN valve opens, brake fluid is supplied to the rear RH brake caliper from
the master cylinder through the ABS IN valve. Brake fluid does not flow into the reservoir because the ABS
OUT valve is closed.
During pressure rear LH brake caliper increases
• When the cut valve 2 and the ABS IN valve opens, brake fluid is supplied to the rear LH brake caliper from
the master cylinder through the ABS IN valve. Brake fluid does not flow into the reservoir because the ABS
OUT valve is closed.
When ABS Function is Starts Operating (During Pressure Holds)
Suction valve 1
Power supply is not supplied (close)
Power supply is not supplied (close)
Suction valve 2
Power supply is not supplied (close)
Power supply is not supplied (close)
ABS IN valve
Power supply is not supplied (open)
Power supply is not supplied (open)
ABS OUT valve
Power supply is not supplied (close)
Power supply is not supplied (close)
Each brake caliper (fluid pressure)
—
Pressure increases
Name
Not activated
During pressure increases
JSFIA0650GB
Name
Not activated
During pressure holds
Cut valve 1
Power supply is not supplied (open)
Power supply is not supplied (open)
Cut valve 2
Power supply is not supplied (open)
Power supply is not supplied (open)
Suction valve 1
Power supply is not supplied (close)
Power supply is not supplied (close)
Revision: 2013 October
2014 JUKE
SYSTEM
BRC-21
< SYSTEM DESCRIPTION >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
During pressure front RH brake caliper holds
• Since the ABS IN valve and the ABS OUT valve are closed, the front RH brake caliper, master cylinder, and
reservoir are blocked. This maintains fluid pressure applied on the front RH brake caliper.
During pressure front LH brake caliper holds
• Since the ABS IN valve and the ABS OUT valve are closed, the front LH brake caliper, master cylinder, and
reservoir are blocked. This maintains fluid pressure applied on the front LH brake caliper.
During pressure rear RH brake caliper holds
• Since the ABS IN valve and the ABS OUT valve are closed, the rear RH brake caliper, master cylinder, and
reservoir are blocked. This maintains fluid pressure applied on the rear RH brake caliper.
During pressure rear LH brake caliper holds
• Since the ABS IN valve and the ABS OUT valve are closed, the rear LH brake caliper, master cylinder, and
reservoir are blocked. This maintains fluid pressure applied on the rear LH brake caliper.
When ABS Function is in Operation (During Pressure Decreases)
Suction valve 2
Power supply is not supplied (close)
Power supply is not supplied (close)
ABS IN valve
Power supply is not supplied (open)
Power supply is supplied (close)
ABS OUT valve
Power supply is not supplied (close)
Power supply is not supplied (close)
Each brake caliper (fluid pressure)
—
Pressure holds
Name
Not activated
During pressure holds
JSFIA0651GB
Name
Not activated
During pressure decreases
Cut valve 1
Power supply is not supplied (open)
Power supply is not supplied (open)
Cut valve 2
Power supply is not supplied (open)
Power supply is not supplied (open)
Suction valve 1
Power supply is not supplied (close)
Power supply is not supplied (close)
Suction valve 2
Power supply is not supplied (close)
Power supply is not supplied (close)
ABS IN valve
Power supply is not supplied (open)
Power supply is supplied (close)
ABS OUT valve
Power supply is not supplied (close)
Power supply is supplied (open)
Each brake caliper (fluid pressure)
—
Pressure decreases
Revision: 2013 October
2014 JUKE
BRC-22
< SYSTEM DESCRIPTION >
[WITH VDC]
SYSTEM
During pressure front RH brake caliper decreases
• Since the ABS IN valve is closed and the ABS OUT valve is opened, fluid pressure applied on the front RH
brake caliper is supplied to the reservoir through the ABS OUT valve. This fluid pressure decreases when
sent to the master cylinder by the pump.
During pressure front LH brake caliper decreases
• Since the ABS IN valve is closed and the ABS OUT valve is opened, fluid pressure applied on the front LH
brake caliper is supplied to the reservoir through the ABS OUT valve. This fluid pressure decreases when
sent to the master cylinder by the pump.
During pressure rear RH brake caliper decreases
• Since the ABS IN valve is closed and the ABS OUT valve is opened, fluid pressure applied on the rear RH
brake caliper is supplied to the reservoir through the ABS OUT valve. This fluid pressure decreases when
sent to the master cylinder by the pump.
During pressure rear LH brake caliper decreases
• Since the ABS IN valve is closed and the ABS OUT valve is opened, fluid pressure applied on the rear LH
brake caliper is supplied to the reservoir through the ABS OUT valve. This fluid pressure decreases when
sent to the master cylinder by the pump.
When ABS Function is in Operation (During Pressure Increases)
During pressure front RH brake caliper increases
JSFIA0649GB
Name
Not activated
During pressure increases
Cut valve 1
Power supply is not supplied (open)
Power supply is not supplied (open)
Cut valve 2
Power supply is not supplied (open)
Power supply is not supplied (open)
Suction valve 1
Power supply is not supplied (close)
Power supply is not supplied (close)
Suction valve 2
Power supply is not supplied (close)
Power supply is not supplied (close)
ABS IN valve
Power supply is not supplied (open)
Power supply is not supplied (open)
ABS OUT valve
Power supply is not supplied (close)
Power supply is not supplied (close)
Each brake caliper (fluid pressure)
—
Pressure increases
Revision: 2013 October
2014 JUKE
SYSTEM
BRC-23
< SYSTEM DESCRIPTION >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
• Brake fluid is supplied to the front RH brake caliper from the master cylinder through the cut valve 2 and the
ABS IN valve. Since the suction valve 2 and the ABS OUT valve is closed, the fluid does not flow into the
reservoir. The amount of brake fluid supplied to the front RH brake caliper from the master cylinder is con-
trolled according to time that the ABS IN valve is not energized (time that the ABS IN valve is open).
During pressure front LH brake caliper increases
• Brake fluid is supplied to the front LH brake caliper from the master cylinder through the cut valve 1 and the
ABS IN valve. Since the suction valve 1 and the ABS OUT valve is closed, the fluid does not flow into the
reservoir. The amount of brake fluid supplied to the front LH brake caliper from the master cylinder is con-
trolled according to time that the ABS IN valve is not energized (time that the ABS IN valve is open).
During pressure rear RH brake caliper increases
• Brake fluid is supplied to the rear RH brake caliper from the master cylinder through the cut valve 1 and the
ABS IN valve. Since the suction valve 1 and the ABS OUT valve is closed, the fluid does not flow into the
reservoir. The amount of brake fluid supplied to the rear RH brake caliper from the master cylinder is con-
trolled according to time that the ABS IN valve is not energized (time that the ABS IN valve is open).
During pressure rear LH brake caliper increases
• Brake fluid is supplied to the rear LH brake caliper from the master cylinder through the cut valve 2 and the
ABS IN valve. Since the suction valve 2 and the ABS OUT valve is closed, the fluid does not flow into the
reservoir. The amount of brake fluid supplied to the rear LH brake caliper from the master cylinder is con-
trolled according to time that the ABS IN valve is not energized (time that the ABS IN valve is open).
When Brake Release
JSFIA0652GB
Name
Not activated
During brake release
Cut valve 1
Power supply is not supplied (open)
Power supply is not supplied (open)
Cut valve 2
Power supply is not supplied (open)
Power supply is not supplied (open)
Suction valve 1
Power supply is not supplied (close)
Power supply is not supplied (close)
Suction valve 2
Power supply is not supplied (close)
Power supply is not supplied (close)
ABS IN valve
Power supply is not supplied (open)
Power supply is not supplied (open)
ABS OUT valve
Power supply is not supplied (close)
Power supply is not supplied (close)
Each brake caliper (fluid pressure)
—
Pressure decreases
Revision: 2013 October
2014 JUKE
BRC-24
< SYSTEM DESCRIPTION >
[WITH VDC]
SYSTEM
During front RH brake caliper release
• Brake fluid is supplied to the front RH brake caliper through the return check valve of the ABS IN valve and
the cut valve 2, and returns to the master cylinder.
During front LH brake caliper release
• Brake fluid is supplied to the front LH brake caliper through the return check valve of the ABS IN valve and
the cut valve 1, and returns to the master cylinder.
During rear RH brake caliper release
• Brake fluid is supplied to the rear RH brake caliper through the return check valve of the ABS IN valve and
the cut valve 1, and returns to the master cylinder.
During rear LH brake caliper release
• Brake fluid is supplied to the rear LH brake caliper through the return check valve of the ABS IN valve and
the cut valve 2, and returns to the master cylinder.
Component Parts and Function
CONDITION FOR TURN ON THE WARNING LAMP
Turns ON when ignition switch turns ON and turns OFF when the system is normal, for bulb check purposes.
CONDITION FOR TURN ON THE INDICATOR LAMP
Component
Function
Pump
Returns the brake fluid reserved in reservoir to master cylinder by reducing pressure.
Motor
Activates the pump according to signals from ABS actuator and electric unit (control unit).
Cut valve 1
Cut valve 2
Shuts off the ordinary brake line from master cylinder.
Suction valve 1
Suction valve 2
Supplies the brake fluid from master cylinder to the pump.
ABS IN valve
Switches the fluid pressure line to increase or hold according to signals from control unit.
ABS OUT valve
Switches the fluid pressure line to increase, hold or decrease according to signals from control unit.
Inlet valve
Brake fluid sucked from the reservoir by the pump does not backflow.
Outlet valve
Brake fluid discharged from the pump does not backflow.
Return check valve
Returns the brake fluid from brake caliper and wheel cylinder to master cylinder by bypassing orifice
of each valve when brake is released.
Reservoir
Temporarily reserves the brake fluid drained from brake caliper, so that pressure efficiently decreas-
es when decreasing pressure of brake caliper and wheel cylinder.
Condition (status)
ABS warning lamp
Brake warning lamp
VDC warning lamp
Ignition switch OFF
OFF
OFF
OFF
For approx. 1 second after the ignition switch is turned ON
ON
ON
ON
Approx. 1 second after ignition switch is turned ON (when the sys-
tem is in normal operation)
OFF
OFF
OFF
After engine starts
OFF
OFF
OFF
When parking brake operates (parking brake switch ON)
OFF
ON
OFF
When brake fluid is less than the specified level (brake fluid level
switch ON)
OFF
ON
OFF
VDC function is malfunctioning
OFF
OFF
ON
TCS function is malfunctioning
OFF
OFF
ON
ABS function is malfunctioning
ON
OFF
ON
EBD function is malfunctioning
ON
ON
ON
Brake limited slip differential (BLSD) function is malfunctioning
OFF
OFF
ON
VDC function is operating
OFF
OFF
Blinking
TCS function is operating
OFF
OFF
Blinking
Revision: 2013 October
2014 JUKE
SYSTEM
BRC-25
< SYSTEM DESCRIPTION >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
• Turns ON when VDC function and TCS function are switched to non-operational status (OFF) by VDC OFF
switch.
• Turns ON when ignition switch turns ON and turns OFF when the system is normal, for bulb check purposes.
Fail-safe
INFOID:0000000009752895
VDC FUNCTION, TCS FUNCTION AND BRAKE LIMITED SLIP DIFFERENTIAL (BLSD) FUNCTION
VDC warning lamp in combination meter turn ON when a malfunction occurs in system [ABS actuator and
electric unit (control unit)]. The control is suspended for VDC function, TCS function and brake limited slip dif-
ferential (BLSD) function. The vehicle status becomes the same as models without VDC function, TCS func-
tion and brake limited slip differential (BLSD) function. However, ABS function and EBD function are operated
normally.
ABS FUNCTION
ABS warning lamp and VDC warning lamp in combination meter turn ON when a malfunction occurs in system
[ABS actuator and electric unit (control unit)]. The control is suspended for VDC function, TCS function, ABS
function and brake limited slip differential (BLSD) function. The vehicle status becomes the same as models
without VDC function, TCS function, ABS function and brake limited slip differential (BLSD) function. However,
EBD function is operated normally.
NOTE:
ABS self-diagnosis sound may be heard the same as in the normal condition, because self-diagnosis is per-
formed when ignition switch turns ON and when vehicle initially starts.
EBD FUNCTION
ABS warning lamp, brake warning lamp and VDC warning lamp in combination meter turn ON when a mal-
function occurs in system [ABS actuator and electric unit (control unit)]. The control is suspended for VDC
function, TCS function, ABS function, EBD function and brake limited slip differential (BLSD) function. The
vehicle status becomes the same as models without VDC function, TCS function, ABS function, EBD function
and brake limited slip differential (BLSD) function.
Condition (status)
VDC OFF indicator lamp
Ignition switch OFF
OFF
For approx. 1 second after the ignition switch is turned ON
ON
Approx. 1 second after ignition switch is turned ON (when the sys-
tem is in normal operation)
OFF
When VDC OFF switch is ON (VDC function and TCS function are
OFF)
ON
Revision: 2013 October
2014 JUKE
BRC-26
< SYSTEM DESCRIPTION >
[WITH VDC]
SYSTEM
DTC
Malfunction detected condition
Fail-safe condition
C1101
When an open circuit is detected in rear RH wheel sensor circuit.
The following functions are sus-
pended.
• VDC function
• TCS function
• ABS function
• EBD function (only when both 2
rear wheels are malfunctioning)
• Brake limited slip differential
(BLSD) function
C1102
When an open circuit is detected in rear LH wheel sensor circuit.
C1103
When an open circuit is detected in front RH wheel sensor circuit.
C1104
When an open circuit is detected in front LH wheel sensor circuit.
C1105
• When a short circuit is detected in rear RH wheel sensor circuit.
• When power supply voltage of rear RH wheel sensor is in following state.
- Rear RH wheel sensor power supply voltage: 7.5 V
≥
Rear RH wheel sensor pow-
er supply voltage
- Rear RH wheel sensor power supply voltage: 16 V
≤
Rear RH wheel sensor power
supply voltage
• When distance between rear RH wheel sensor and rear RH wheel sensor rotor is
large.
• When installation of rear RH wheel sensor or rear RH wheel sensor rotor is not
normal.
C1106
• When a short circuit is detected in rear LH wheel sensor circuit.
• When power supply voltage of rear LH wheel sensor is in following state.
- Rear LH wheel sensor power supply voltage: 7.5 V
≥
Rear LH wheel sensor power
supply voltage
- Rear LH wheel sensor power supply voltage: 16 V
≤
Rear LH wheel sensor power
supply voltage
• When distance between rear LH wheel sensor and rear LH wheel sensor rotor is
large.
• When installation of rear LH wheel sensor or rear LH wheel sensor rotor is not nor-
mal.
C1107
• When a short circuit is detected in front RH wheel sensor circuit.
• When power supply voltage of front RH wheel sensor is in following state.
- Front RH wheel sensor power supply voltage: 7.5 V
≥
Front RH wheel sensor
power supply voltage
- Front RH wheel sensor power supply voltage: 16 V
≤
Front RH wheel sensor pow-
er supply voltage
• When distance between front RH wheel sensor and front RH wheel sensor rotor
is large.
• When installation of front RH wheel sensor or front RH wheel sensor rotor is not
normal.
C1108
• When a short circuit is detected in front LH wheel sensor circuit.
• When power supply voltage of front LH wheel sensor is in following state.
- Front LH wheel sensor power supply voltage: 7.5 V
≥
Front LH wheel sensor pow-
er supply voltage
- Front LH wheel sensor power supply voltage: 16 V
≤
Front LH wheel sensor power
supply voltage
• When distance between front LH wheel sensor and front LH wheel sensor rotor is
large.
• When installation of front LH wheel sensor or front LH wheel sensor rotor is not
normal.
C1109
When ignition power supply voltage is in following state.
• Ignition power supply voltage: 10 V
≥
Ignition power supply voltage.
• Ignition power supply voltage: 16 V
≤
Ignition power supply voltage.
The following functions are sus-
pended.
• VDC function
• TCS function
• ABS function
• EBD function
• Brake limited slip differential
(BLSD) function
C1110
When there is an internal malfunction in the ABS actuator and electric unit (control
unit).
C1111
When a malfunction is detected in motor or motor relay.
The following functions are sus-
pended.
• VDC function
• TCS function
• ABS function
• Brake limited slip differential
(BLSD) function
Revision: 2013 October
2014 JUKE
SYSTEM
BRC-27
< SYSTEM DESCRIPTION >
[WITH VDC]
C
D
E
G
H
I
J
K
L
M
A
B
BRC
N
O
P
C1113
When a malfunction is detected in decel G signal, or signal line of yaw rate/side/de-
cel G sensor is open or shorted.
The following functions are sus-
pended.
• VDC function
• TCS function
• ABS function (AWD)
• Brake limited slip differential
(BLSD) function
C1115
When difference in wheel speed between any wheel and others is detected the ve-
hicle is driven, because of installation of other tires than specified.
The following functions are sus-
pended.
• VDC function
• TCS function
• ABS function
• EBD function
• Brake limited slip differential
(BLSD) function
C1116
When stop lamp switch signal is not input when brake pedal operates.
The following functions are sus-
pended.
• VDC function
• TCS function
• Brake limited slip differential
(BLSD) function
C1120
When a malfunction is detected in front LH ABS IN valve.
The following functions are sus-
pended.
• VDC function
• TCS function
• ABS function
• EBD function
• Brake limited slip differential
(BLSD) function
C1121
When a malfunction is detected in front LH ABS OUT valve.
C1122
When a malfunction is detected in front RH ABS IN valve.
C1123
When a malfunction is detected in front RH ABS OUT valve.
C1124
When a malfunction is detected in rear LH ABS IN valve.
C1125
When a malfunction is detected in rear LH ABS OUT valve.
C1126
When a malfunction is detected in rear RH ABS IN valve.
C1127
When a malfunction is detected in rear RH ABS OUT valve.
C1130
When a malfunction is detected in ECM system.
The following functions are sus-
pended.
• VDC function
• TCS function
• Brake limited slip differential
(BLSD) function
C1140
When a malfunction is detected in actuator relay.
The following functions are sus-
pended.
• VDC function
• TCS function
• ABS function
• EBD function
• Brake limited slip differential
(BLSD) function
C1143
When a malfunction is detected in steering angle sensor.
The following functions are sus-
pended.
• VDC function
• TCS function
• ABS function (AWD)
• Brake limited slip differential
(BLSD) function
C1144
When neutral position adjustment of steering angle sensor is not complete.
The following functions are sus-
pended.
• VDC function
• TCS function
• Brake limited slip differential
(BLSD) function
DTC
Malfunction detected condition
Fail-safe condition
Revision: 2013 October
2014 JUKE
BRC-28
< SYSTEM DESCRIPTION >
[WITH VDC]
SYSTEM
VDC FUNCTION
VDC FUNCTION : System Description
INFOID:0000000009752896
• Side slip or tail slip may occur while driving on a slippery road or intending an urgent evasive driving. VDC
function detects side slip status using each sensor when side slip or tail slip is about to occur and improves
vehicle stability by brake control and engine output control during driving.
• In addition to ABS function, EBD function and TCS function, target side slip amount is calculated according
to steering operation amount from steering angle sensor. By comparing this information with vehicle side slip
amount that is calculated from information from yaw rate/side/decel G sensor and wheel sensor, vehicle driv-
C1145
When a malfunction is detected in yaw rate signal, or signal line of yaw rate/side/
decel G sensor is open or shorted.
The following functions are sus-
pended.
• VDC function
• TCS function
• ABS function (AWD)
• Brake limited slip differential
(BLSD) function
C1146
When a malfunction is detected in side G signal, or signal line of yaw rate/side/decel
G sensor is open or shorted.
C1155
When brake fluid level low signal is detected.
The following functions are sus-
pended.
• VDC function
• TCS function
• Brake limited slip differential
(BLSD) function
C1164
When a malfunction is detected in cut valve 1.
The following functions are sus-
pended.
• VDC function
• TCS function
• ABS function
• EBD function
• Brake limited slip differential
(BLSD) function
C1165
When a malfunction is detected in cut valve 2.
C1166
When a malfunction is detected in suction valve 1.
C1167
When a malfunction is detected in suction valve 2.
C1170
When the information in ABS actuator and electric unit (control unit) is not the same.
The following functions are sus-
pended.
• VDC function
• TCS function
• ABS function
• Brake limited slip differential
(BLSD) function
C1176
When brake pedal position switch signal is not input when brake pedal operates.
The following functions are sus-
pended.
• VDC function
• TCS function
• Brake limited slip differential
(BLSD) function
U1000
When CAN communication signal is not continuously transmitted or received for 2
seconds or more.
The following functions are sus-
pended.
• VDC function
• TCS function
• Brake limited slip differential
(BLSD) function
U1010
When detecting error during the initial diagnosis of CAN controller of ABS actuator
and electric unit (control unit).
DTC
Malfunction detected condition
Fail-safe condition
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст