Nissan Juke (2014 year). Service Repair Manual — part 14
BCS-22
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*
1
: For models without auto light system, this item is displayed, but cannot be used.
*
2
: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Service item
Setting item
Setting
CUSTOM A/LIGHT SET-
TING*
1
MODE 1*
2
Normal
MODE 2
More sensitive setting than normal setting (Turns ON earlier than normal opera-
tion)
MODE 3
More sensitive setting than MODE 2 (Turns ON earlier than MODE 2)
MODE 4
Less sensitive setting than normal setting (Turns ON later than normal operation)
BATTERY SAVER SET
On*
2
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
ILL DELAY SET*
1
MODE 1*
2
45 sec.
Sets delay timer function timer operation time
(All doors closed)
MODE 2
Without the
function
MODE 3
30 sec.
MODE 4
60 sec.
MODE 5
90 sec.
MODE 6
120 sec.
MODE 7
150 sec.
MODE 8
180 sec.
HEAD LIGHT TIMER
MODE 1
10 sec.
Sets follow me home function activating time
MODE 2
*2
30 sec.
AUTO LIGHT LOGIC SET*
1
MODE 1*
2
With twilight ON custom & with wiper INT, LO and HI
MODE 2
With twilight ON custom & with wiper LO and HI
MODE 3
With twilight ON custom & without
MODE 4
Without twilight ON custom & with wiper INT, LO and HI
MODE 5
Without twilight ON custom & with wiper LO and HI
MODE 6
Without twilight ON custom & without
Monitor item
[Unit]
Description
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
ENGINE STATE
[Stop/Stall/Crank/Run]
Indicates [Stop/Stall/Crank/Run] condition of engine states
VEH SPEED 1
[km/h]
Display the vehicle speed signal received from combination meter by numerical value
[Km/h]
Revision: 2013 October
2014 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-23
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
*: For models without front fog lamp, this item is displayed, but cannot be monitored.
ACTIVE TEST
TURN SIGNAL R
[On/Off]
Each switch status that BCM judges from the combination switch reading function
TURN SIGNAL L
[On/Off]
TAIL LAMP SW
[On/Off]
HI BEAM SW
[On/Off]
HEAD LAMP SW1
[On/Off]
HEAD LAMP SW2
[On/Off]
PASSING SW
[On/Off]
AUTO LIGHT SW
[On/Off]
FR FOG SW*
[On/Off]
DOOR SW-DR
[On/Off]
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
[On/Off]
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
[On/Off]
Indicated [On/Off] condition of rear door switch RH
DOOR SW- RL
[On/Off]
Indicated [On/Off] condition of rear door switch LH
DOOR SW-BK
[On/Off]
Indicated [On/Off] condition of back door switch
OPTICAL SENSOR
[On/Off/NG]
NOTE:
This item is displayed, but cannot be monitored
OPTI SEN (DTCT)
[V]
The value of outside brightness voltage input from the optical sensor
OPTI SEN (FILT)
[V]
The value of outside brightness voltage filtered by BCM
Monitor item
[Unit]
Description
Test item
Operation
Description
TAIL LAMP
On
Transmits the position light request signal to IPDM E/R via CAN commu-
nication to turn the tail lamp ON
Off
Stops the tail lamp request signal transmission
HEAD LAMP
Hi
Transmits the high beam request signal via CAN communication to turn
the headlamp (HI)
Lo
Transmits the low beam request signal via CAN communication to turn
the headlamp (LO)
Off
Stops the high & low beam request signal transmission
Revision: 2013 October
2014 JUKE
BCS-24
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*
1
: Except for NISMO models without front fog lamp, this item is displayed, but cannot be tested.
*
2
: For NISMO models with daytime running light system, this item is displayed, but cannot be tested.
*
3
: Except for NISMO models with daytime running light system.
*
4
: For NISMO models with daytime running light system.
WIPER
WIPER : CONSULT Function - WIPER
INFOID:0000000010286823
WORK SUPPORT
*:Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
FR FOG LAMP*
1
On
• Transmits the front fog lights request signal to IPDM E/R via CAN com-
munication to turn the front fog lamp ON*
3
• Transmits the daytime running light request signal to IPDM E/R via
CAN communication to turn the daytime running light ON*
4
Off
• Stops the front fog light request signal transmission*
3
• Stops the daytime running light request signal transmission*
4
DAYTIME RUNNING LIGHT*
2
On
Transmits the daytime running light request signal via CAN communica-
tion to IPDM E/R
Off
Stop the daytime running light request signal transmission
ILL DIM SIGNAL
On
NOTE:
This item is indicated, but can not tested
Off
Test item
Operation
Description
Service item
Setting item
Description
WIPER SPEED
SETTING
On
With vehicle speed
(Front wiper intermittent time linked with the vehicle speed and wiper intermittent dial position)
Off*
Without vehicle speed
(Front wiper intermittent time linked with the wiper intermittent dial position)
Monitor Item
[Unit]
Description
PUSH SW
[Off/On]
The switch status input from push-button ignition switch
VEH SPEED 1
[km/h]
Displays the value of the vehicle speed signal received from combination meter via CAN com-
munication
FR WIPER HI
[Off/On]
Status of each switch judged by BCM using the combination switch reading function
FR WIPER LOW
[Off/On]
FR WASHER SW
[Off/On]
FR WIPER INT
[Off/On]
FR WIPER STOP
[Off/On]
Displays the status of the front wiper stop position signal received from IPDM E/R via CAN
communication.
INT VOLUME
[1
−
7]
Status of each switch judged by BCM using the combination switch reading function
Revision: 2013 October
2014 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-25
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER)
INFOID:0000000010286813
WORK SUPPORT
*: Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
RR WIPER ON
[Off/On]
Status of each switch judged by BCM using the combination switch reading function
RR WIPER INT
[Off/On]
RR WASHER SW
[Off/On]
RR WIPER STOP
[Off/On]
Rear wiper motor (stop position) status input from the rear wiper motor
RAIN SENSOR
[Off/LOW/HIGH/SPLASH/NG]
NOTE:
This item is displayed, but cannot be monitored.
Monitor Item
[Unit]
Description
Test item
Operation
Description
FR WIPER
Hi
Transmits the front wiper request signal (HI) to IPDM E/R via CAN communication to op-
erate the front wiper HI operation.
Lo
Transmits the front wiper request signal (LO) to IPDM E/R via CAN communication to
operate the front wiper LO operation.
INT
Transmits the front wiper request signal (INT) to IPDM E/R via CAN communication to
operate the front wiper INT operation.
Off
Stops transmitting the front wiper request signal to stop the front wiper operation.
RR WIPER
On
Output the voltage to operate the rear wiper motor.
Off
Stops the voltage to stop the rear wiper motor.
Service item
Setting item
Setting
HAZARD ANSWER
BACK
Lock Only
With locking only
Sets the hazard warning lamp answer back function
when the door is lock/unlock with the request switch or
the Intelligent Key.
Unlk Only
With unlocking only
Lock&Unlk
*
With locking/unlocking
Off
Without the function
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
Indicated [On/Off] condition of door request switch (driver side)
REQ SW-AS
[On/Off]
Indicated [On/Off] condition of door request switch (passenger side)
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
Revision: 2013 October
2014 JUKE
BCS-26
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
AIR CONDITIONER
AIR CONDITIONER : CONSULT Function (BCM - AIR CONDITIONER) (Automatic A/
C)
INFOID:0000000010286779
DATA MONITOR
Display Item List
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)
INFOID:0000000010286782
WORK SUPPORT
TURN SIGNAL R
[On/Off]
Each switch status that BCM detects from the combination switch reading function
TURN SIGNAL L
[On/Off]
HAZARD SW
[On/Off]
The switch status input from the hazard switch
RKE-LOCK
[On/Off]
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
[On/Off]
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-PANIC
[On/Off]
Indicates [On/Off] condition of PANIC button of Intelligent Key
Monitor item
[Unit]
Description
Test item
Operation
Description
FLASHER
RH
Outputs the voltage to turn the right side turn signal lamps ON
LH
Outputs the voltage to turn the left side turn signal lamps ON
Off
Stops the voltage to turn the turn signal lamps OFF
Monitor Item [Unit]
Contents
FAN ON SIG
[On/Off]
Displays the blower fan status as jugged from the A/C auto amp.
AIR COND SW
[On/Off]
Displays [COMP (On)/COMP (Off)] status as judged from the A/C auto amp.
Monitor item
Description
INSIDE ANT DIAGNOSIS
This function allows inside key antenna self-diagnosis
LOCK/UNLOCK BY I-KEY
Door lock/unlock function by door request switch mode can be changed to operation in this
mode
• On: Operate
• Off: Non-operation
ENGINE START BY I-KEY
Engine start function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
TRUNK/GLASS HATCH OPEN
NOTE:
This item is displayed, but cannot be monitored
Revision: 2013 October
2014 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-27
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
SELF-DIAG RESULT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
HORN WITH KEYLESS LOCK
Horn reminder function mode by Intelligent Key button can be changed to operate (ON) or not
operate (OFF) with this mode
• On: Operate
• Off: Non-operation
PANIC ALARM SET
Panic alarm button pressing time on Intelligent Key remote control button can be selected from
the following with this mode
• MODE 1: 0.5 sec
• MODE 2: Non-operation
• MODE 3: 1.5 sec
TRUNK OPEN DELAY
NOTE:
This item is displayed, but cannot be monitored
LO- BATT OF KEY FOB WARN
Intelligent Key low battery warning mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
ANTI KEY LOCK IN FUNCTI
Key reminder function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
HAZARD ANSWER BACK
Hazard reminder function mode by door request switch and Intelligent Key button can be se-
lected from the following with this mode
• Lock Only: Door lock operation only
• Unlock Only: Door unlock operation only
• Lock/Unlock: Lock and unlock operation
• Off: Non-operation
ANS BACK I-KEY LOCK
Buzzer reminder function (lock operation) mode by door request switch can be selected from
the following with this mode
• Horn Chirp: Sound horn
• Buzzer: Sound Intelligent Key warning buzzer
• Off: Non-operation
ANS BACK I-KEY UNLOCK
Buzzer reminder function (unlock operation) mode by door request switch can be changed to
operation with this mode
• On: Operate
• Off: Non-operation
SHORT CRANKING OUTPUT
Starter motor can operate during the times below
• 70 msec
• 100 msec
• 200 msec
CONFIRM KEY FOB ID
It can be checked whether Intelligent Key ID code is registered or not in this mode
AUTO LOCK SET
Auto door lock operation time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes
Monitor item
Description
Monitor Item
Condition
REQ SW -DR
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
Indicates [On/Off] condition of door request switch (passenger side)
REQ SW -BD/TR
Indicates [On/Off] condition of back door request switch
Revision: 2013 October
2014 JUKE
BCS-28
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
PUSH SW
Indicates [On/Off] condition of push-button ignition switch
CLUTCH SW*
1
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
DETE/CANCL SW
Indicates [On/Off] condition of P position
SFT PN/N SW
Indicates [On/Off] condition of P or N position
UNLK SEN -DR
Indicates [On/Off] condition of driver door UNLOCK status
PUSH SW -IPDM
Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B
Indicates [On/Off] condition of ignition relay 1
DETE SW -IPDM
Indicates [On/Off] condition of P position
SFT PN -IPDM
Indicates [On/Off] condition of P or N position
SFT P -MET
Indicates [On/Off] condition of P position
SFT N -MET
Indicates [On/Off] condition of N position
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
S/L LOCK-IPDM
NOTE:
This item is displayed, but cannot be monitored
S/L UNLK-IPDM
NOTE:
This item is displayed, but cannot be monitored
S/L RELAY-REQ
NOTE:
This item is displayed, but cannot be monitored
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver side door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger side door status
ID OK FLAG
Indicates [Set/Reset] condition of key ID
PRMT ENG STRT
Indicates [Set/Reset] condition of engine start possibility
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
Indicates [On/Off] condition of PANIC button of Intelligent Key
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
Revision: 2013 October
2014 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-29
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
COMB SW
COMB SW : CONSULT Function (BCM - COMB SW)
INFOID:0000000009751602
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Test item
Description
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Take Out: Take away warning chime sounds when CONSULT screen is touched
• Key: Key warning chime sounds when CONSULT screen is touched
• Knob: OFF position warning chime sounds when CONSULT screen is touched
• Off: Non-operation
INDICATOR
This test is able to check warning lamp operation
• KEY ON: “KEY” Warning lamp illuminates when CONSULT screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT screen is touched
• Off: Non-operation
INT LAMP
This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation
LCD
This test is able to check meter display information
• BP N: Engine start operation indicator lamp indicate when CONSULT screen is touched
• BP I: Engine start operation indicator lamp indicate when CONSULT screen is touched
• ID NG: This item is displayed, but cannot be monitored
• ROTAT: This item is displayed, but cannot be monitored
• SFT P: Shift P warning lamp indicate when CONSULT screen is touched
• INSRT: This item is displayed, but cannot be monitored
• BATT: Key warning lamp indicator when CONSULT screen is touched
• NO KY: Key warning lamp indicator when CONSULT screen is touched
• OUTKEY: Engine start operation indicator lamp indicate when CONSULT screen is touched
• LK WN: Engine start operation indicator lamp indicate when CONSULT screen is touched
FLASHER
This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT screen is touched
HORN
This test is able to check horn operation
The horn is activated after “ON” on CONSULT screen is touched
P RANGE
This test is able to check CVT shift selector power supply
• On: Operate
• Off: Non-operation
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT screen is touched
PUSH SWITCH INDICATOR
This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT screen is touched
BATTERY SAVER
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT screen is touched.
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation.
This actuator opens when “Open” on CONSULT screen is touched.
Monitor item [UNIT]
Description
FR WIPER HI
[Off/On]
Displays the status of the FR WIPER HI switch in combination switch judged by BCM with the combination
switch reading function.
FR WIPER LOW
[Off/On]
Displays the status of the FR WIPER LOW switch in combination switch judged by BCM with the combination
switch reading function.
Revision: 2013 October
2014 JUKE
BCS-30
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
BCM
BCM : CONSULT Function (BCM - BCM)
INFOID:0000000009751603
WORK SUPPORT
IMMU
IMMU : CONSULT Function (BCM - IMMU)
INFOID:0000000010286806
WORK SUPPORT
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
FR WASHER SW
[Off/On]
Displays the status of the FR WASHER switch in combination switch judged by BCM with the combination
switch reading function.
FR WIPER INT
[Off/On]
Displays the status of the FR WIPER INT switch in combination switch judged by BCM with the combination
switch reading function.
INT VOLUME
[1 - 7]
Displays the status of wiper volume dial position judged by BCM with the combination switch reading function.
TURN SIGNAL R
[Off/On]
Displays the status of the TURN RH switch in combination switch judged by BCM with the combination switch
reading function.
TURN SIGNAL L
[Off/On]
Displays the status of the TURN LH switch in combination switch judged by BCM with the combination switch
reading function.
TAIL LAMP SW
[Off/On]
Displays the status of the TAIL LAMP switch in combination switch judged by BCM with the combination
switch reading function.
HI BEAM SW
[Off/On]
Displays the status of the HI BEAM switch in combination switch judged by BCM with the combination switch
reading function.
HEAD LAMP SW 1
[Off/On]
Displays the status of the HEADLAMP 1 switch in combination switch judged by BCM with the combination
switch reading function.
HEAD LAMP SW 2
[Off/On]
Displays the status of the HEADLAMP 2 switch in combination switch judged by BCM with the combination
switch reading function.
PASSING SW
[Off/On]
Displays the status of the PASSING switch in combination switch judged by BCM with the combination switch
reading function.
AUTO LIGHT SW
[Off/On]
Displays the status of the AUTO LIGHT switch in combination switch judged by BCM with the combination
switch reading function.
FR FOG SW
[Off/On]
Displays the status of the FR FOG switch in combination switch judged by BCM with the combination switch
reading function.
Monitor item [UNIT]
Description
Item
Description
RESET SETTING VALUE
Return a value set with Work Support of each system to a default value in factory shipment.
Service item
Description
CONFIRM DONGLE ID
It is possible to check that dongle unit is applied to the vehicle.
Monitor item
Content
CONFRM ID ALL
Indicates [YET] at all time.
Switches to [DONE] when a registered Intelligent Key backside is contacted to push-button igni-
tion switch.
CONFIRM ID4
CONFIRM ID3
CONFIRM ID2
CONFIRM ID1
Revision: 2013 October
2014 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-31
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST
BATTERY SAVER
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)
INFOID:0000000010286820
WORK SUPPORT
*:Factory setting
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
NOT REGISTERED
Indicates [ID OK] when key ID that is registered is received or is not yet received.
Indicates [ID NG] when key ID that is not registered is received.
TP 4
Indicates the number of IDs that are registered.
TP 3
TP 2
TP 1
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch.
Monitor item
Content
Test item
Description
THEFT IND
This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen is touched.
Service item
Setting item
Setting
ROOM LAMP TIMER SET
MODE 1
30 min.
Sets the interior room lamp battery saver timer operating
time.
NOTE:
The factor setting is 10 minutes. The setting cannot be re-
turned to the factory setting, when the setting is changed
once.
MODE 2
60 min.
MODE 3
15 min.
BATTERY SAVER SET
On
*
With the exterior lamp battery saver function
Off
Without the exterior lamp battery saver function
Monitor item
[Unit]
Description
REQ SW-DR
[On/Off]
Indicated [On/Off] condition of door request switch (driver side)
REQ SW-AS
[On/Off]
Indicated [On/Off] condition of door request switch (passenger side)
REQ SW-RR
[On/Off]
NOTE:
This item is displayed, but cannot be monitored
REQ SW-RL
[On/Off]
NOTE:
This item is displayed, but cannot be monitored
PUSH SW
[On/Off]
Indicates [On/Off] condition of push-button ignition switch
UNLK SEN -DR
[On/Off]
Indicates [On/Off] condition of driver door UNLOCK status
DOOR SW-DR
[On/Off]
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
[On/Off]
Indicated [On/Off] condition of front door switch (passenger side)
Revision: 2013 October
2014 JUKE
BCS-32
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
ACTIVE TEST
TRUNK
TRUNK : CONSULT Function (BCM - TRUNK)
INFOID:0000000010286783
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
THEFT ALM
THEFT ALM : CONSULT Function (BCM - THEFT)
INFOID:0000000010286787
WORK SUPPORT
DOOR SW-RR
[On/Off]
Indicated [On/Off] condition of rear door switch RH
DOOR SW- RL
[On/Off]
Indicated [On/Off] condition of rear door switch LH
DOOR SW- BK
[On/Off]
Indicated [On/Off] condition of back door switch
CDL LOCK SW
[On/Off]
Indicated [On/Off] condition of lock signal from door lock unlock switch
CDL UNLOCK SW
[On/Off]
Indicated [On/Off] condition of unlock signal from door lock unlock switch
TRNK/HAT MNTR
[On/Off]
NOTE:
This item is displayed, but cannot be monitored
KEY CYL LK-SW
[On/Off]
Indicated [On/Off] condition of lock signal from door key cylinder
KEY CYL UN-SW
[On/Off]
Indicated [On/Off] condition of unlock signal from door key cylinder
RKE-LOCK
[On/Off]
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
[On/Off]
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
Monitor item
[Unit]
Description
Test item
Operation
Description
BATTERY SAVER
Off
Cuts the interior room lamp power supply.
On
Outputs the interior room lamp power supply.
Monitor Item
Contents
PUSH SW
Indicates [On/Off] condition of push switch
UNLK SEN -DR
Indicates [On/Off] condition of unlock sensor
VEH SPEED 1
Indicates [Km/h] condition of vehicle speed signal from combination meter
TR/BD OPEN SW
Indicates [ON/OFF] condition of back door opener switch.
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
Revision: 2013 October
2014 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-33
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
RETAIND PWR
Service Item
Description
SECURITY ALARM SET
This mode is able to confirm and change security alarm ON-OFF setting.
THEFT ALM TRG
The switch which triggered vehicle security alarm is recorded.
This mode is able to confirm and erase the record of vehicle security alarm.
The trigger data can be erased by touching “CLEAR” on CONSULT screen.
Monitored Item
Description
REQ SW -DR
Indicates [ON/OFF] condition of door request switch (driver side).
REQ SW -AS
Indicates [ON/OFF] condition of door request switch (passenger side).
REQ SW -RR
NOTE:
This is displayed even when it is not equipped.
REQ SW -RL
NOTE:
This is displayed even when it is not equipped.
REQ SW -BD/TR
Indicates [ON/OFF] condition of back door request switch.
PUSH SW
Indicates [ON/OFF] condition of push-button ignition switch
UNLK SEN -DR
Indicates [ON/OFF] condition of driver door UNLOCK status.
DOOR SW-DR
Indicates [ON/OFF] condition of front door switch (driver side).
DOOR SW-AS
Indicates [ON/OFF] condition of front door switch (passenger side).
DOOR SW-RR
Indicates [ON/OFF] condition of rear door switch RH.
DOOR SW-RL
Indicates [ON/OFF] condition of rear door switch LH.
DOOR SW-BK
Indicates [ON/OFF] condition of back door switch.
CDL LOCK SW
Indicates [ON/OFF] condition of lock signal from door lock/unlock switch.
CDL UNLOCK SW
Indicates [ON/OFF] condition of unlock signal from door lock/unlock switch.
KEY CYL LK-SW
Indicates [ON/OFF] condition of lock signal from door key cylinder.
KEY CYL UN-SW
Indicates [ON/OFF] condition of unlock signal from door key cylinder.
TR/BD OPEN SW
Indicates [ON/OFF] condition of back door opener switch.
TRNK/HAT MNTR
NOTE:
This is displayed even when it is not equipped.
RKE-LOCK
Indicates [ON/OFF] condition of LOCK signal from Intelligent Key.
RKE-UNLOCK
Indicates [ON/OFF] condition of UNLOCK signal from Intelligent Key.
RKE-TR/BD
NOTE:
This is displayed even when it is not equipped.
Test Item
Description
THEFT IND
This test is able to check security indicator lamp operation.
Security indicator lamp is turned on when “ON” on CONSULT screen is touched.
VEHICLE SECURITY HORN
This test is able to check horns operation.
Horns are activated for 0.5 seconds after “ON” on CONSULT screen is touched.
HEADLAMP(HI)
This test is able to check headlamp operation.
Headlamps are activated for 0.5 seconds after “ON” on CONSULT screen is touched.
FLASHER
This test is able to check hazard warning lamp operation.
Hazard warning lamps are activated after “ON” on CONSULT screen is touched.
Revision: 2013 October
2014 JUKE
BCS-34
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
DIAGNOSIS SYSTEM (BCM)
RETAIND PWR : CONSULT Function (BCM - RETAINED PWR)
INFOID:0000000010286810
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
SIGNAL BUFFER
SIGNAL BUFFER : CONSULT Function (BCM - SIGNAL BUFFER)
INFOID:0000000009751609
DATA MONITOR
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
ACTIVE TEST
AIR PRESSURE MONITOR
AIR PRESSURE MONITOR : CONSULT Function (BCM - AIR PRESSURE MONI-
TOR)
INFOID:0000000010286829
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
SELF DIAGNOSTIC RESULT
DATA MONITOR MODE
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
Monitor Item
Description
DOOR SW-DR
Indicates [ON/OFF] condition of driver side door switch.
DOOR SW-AS
Indicates [ON/OFF] condition of passenger side door switch.
Monitor item [UNIT]
Description
PUSH SW
[Off/On]
Displays the status of the push-button ignition switch (push switch) judged by BCM.
Test item
Opera-
tion
Description
OIL PRESSURE SW
Off
NOTE:
This item is indicated, but not tested.
On
Diagnosis mode
Function Description
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Work Support
Components can be quickly and accurately adjusted.
Revision: 2013 October
2014 JUKE
BCS
DIAGNOSIS SYSTEM (BCM)
BCS-35
< SYSTEM DESCRIPTION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
ACTIVE TEST MODE
NOTE:
After completing the work below, perform an active test.
1.
Check ID registration state and perform self-diagnosis.
2.
Erase the self-diagnosis result history.
WORK SUPPORT
Monitor item (Unit)
Remarks
AIR PRESS FL
(kPa, kg/cm2 or Psi)
Tire pressure
AIR PRESS FR
(kPa, kg/cm2 or Psi)
AIR PRESS RR
(kPa, kg/cm2 or Psi)
AIR PRESS RL
(kPa, kg/cm2 or Psi)
ID REGST FL1
(Yet, Done)
Registration ID
ID REGST FR1
(Yet, Done)
ID REGST RR1
(Yet, Done)
ID REGST RL1
(Yet, Done)
WARNING LAMP
(On/Off)
Low tire pressure warning lamp
BUZZER
(On/Off)
NOTE:
This item is displayed, but cannot be use this item.
Item
Description
WARNING LAMP
Low tire pressure warning lamp can be turned ON arbitrarily.
ID REGIST WARNING
NOTE:
Displayed but not used in TPMS.
RUN FLAT TIRE W/L
NOTE:
Displayed but not used in TPMS.
RUN FLAT/T WARN BUZZER
NOTE:
Displayed but not used in TPMS.
FLASHER
Turn signal lamps can be turned ON arbitrarily.
HORN
This test is able to check to check that the horn sounds.
Item
Description
ID READ
Registered tire pressure sensor ID can be displayed.
ID REGIST
Tire pressure sensor ID can be registered.
Revision: 2013 October
2014 JUKE
BCS-36
< ECU DIAGNOSIS INFORMATION >
[WITH INTELLIGENT KEY SYSTEM]
BCM
ECU DIAGNOSIS INFORMATION
BCM
Reference Value
INFOID:0000000009751611
VALUES ON THE DIAGNOSIS TOOL
NOTE:
The following table includes information (items) inapplicable to this vehicle. For information (items) applicable
to this vehicle, refer to CONSULT display items.
CONSULT MONITOR ITEM
Monitor Item
Condition
Value/Status
FR WIPER HI
Other than front wiper switch HI
Off
Front wiper switch HI
On
FR WIPER LOW
Other than front wiper switch LO
Off
Front wiper switch LO
On
FR WASHER SW
Front washer switch OFF
Off
Front washer switch ON
On
FR WIPER INT
Other than front wiper switch INT
Off
Front wiper switch INT
On
FR WIPER STOP
Front wiper is not in STOP position
Off
Front wiper is in STOP position
On
INT VOLUME
Wiper intermittent dial is in a dial position 1 - 7
Wiper intermittent dial
position
RR WIPER ON
Other than rear wiper switch ON
Off
Rear wiper switch ON
On
RR WIPER INT
Other than rear wiper switch INT
Off
Rear wiper switch INT
On
RR WASHER SW
Rear washer switch OFF
Off
Rear washer switch ON
On
RR WIPER STOP
Rear wiper is in STOP position
Off
Rear wiper is not in STOP position
On
TURN SIGNAL R
Other than turn signal switch RH
Off
Turn signal switch RH
On
TURN SIGNAL L
Other than turn signal switch LH
Off
Turn signal switch LH
On
TAIL LAMP SW
Other than lighting switch 1ST and 2ND
Off
Lighting switch 1ST or 2ND
On
HI BEAM SW
Other than lighting switch HI
Off
Lighting switch HI
On
HEAD LAMP SW 1
Other than lighting switch 2ND
Off
Lighting switch 2ND
On
HEAD LAMP SW 2
Other than lighting switch 2ND
Off
Lighting switch 2ND
On
PASSING SW
Other than lighting switch PASS
Off
Lighting switch PASS
On
AUTO LIGHT SW
Other than lighting switch AUTO
Off
Lighting switch AUTO
On
Revision: 2013 October
2014 JUKE
BCS
BCM
BCS-37
< ECU DIAGNOSIS INFORMATION >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
K
L
B
A
O
P
N
FR FOG SW
Front fog lamp switch OFF
Off
Front fog lamp switch ON
On
DOOR SW-DR
Driver door closed
Off
Driver door opened
On
DOOR SW-AS
Passenger door closed
Off
Passenger door opened
On
DOOR SW-RR
Rear RH door closed
Off
Rear RH door opened
On
DOOR SW-RL
Rear LH door closed
Off
Rear LH door opened
On
DOOR SW-BK
Back door closed
Off
Back door opened
On
CDL LOCK SW
Other than power door lock switch LOCK
Off
Power door lock switch LOCK
On
CDL UNLOCK SW
Other than power door lock switch UNLOCK
Off
Power door lock switch UNLOCK
On
KEY CYL LK-SW
Other than driver door key cylinder LOCK position
Off
Driver door key cylinder LOCK position
On
KEY CYL UN-SW
Other than driver door key cylinder UNLOCK position
Off
Driver door key cylinder UNLOCK position
On
HAZARD SW
Hazard switch is OFF
Off
Hazard switch is ON
On
REAR DEF SW
Rear window defogger switch OFF
Off
Rear window defogger switch ON
On
TR/BD OPEN SW
Back door opener switch OFF
Off
While the back door opener switch is turned ON
On
TRNK/HAT MNTR
NOTE:
The item is indicated, but not monitored.
Off
FAN ON SIG
Blower fan OFF
Off
Blower fan ON
On
AIR COND SW
Air conditioner OFF (A/C switch indicator OFF)
Off
Air conditioner ON (A/C switch indicator ON)
On
RKE-LOCK
LOCK button of the key is not pressed
Off
LOCK button of the key is pressed
On
RKE-UNLOCK
UNLOCK button of the key is not pressed
Off
UNLOCK button of the key is pressed
On
RKE-TR/BD
NOTE:
The item is indicated, but not monitored.
Off
RKE-PANIC
PANIC button of the key is not pressed
Off
PANIC button of the key is pressed
On
RKE-MODE CHG
LOCK/UNLOCK button of the key is not pressed and held simultaneously
Off
LOCK/UNLOCK button of the key is pressed and held simultaneously
On
OPTI SEN (DTCT)
Bright outside of the vehicle
Close to 5 V
Dark outside of the vehicle
Close to 0 V
Monitor Item
Condition
Value/Status
Revision: 2013 October
2014 JUKE
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст