Nissan Murano. Manual — part 452

PRECAUTIONS

DLN-47

< PRECAUTION >

[TRANSFER: TY20A]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

• Check appearance of the disassembled parts for damage, deformation, and unusual wear. Replace them

with a new one if necessary.

• Gaskets, seals, O-rings and lock nuts should be replaced any time when the transfer is disassembled.
• In principle, tighten bolts or nuts gradually in several steps working diagonally from inside to outside. If tight-

ening sequence is specified, use it.

• Observe the specified torque when assembling.
• Clean and flush the parts sufficiently and blow-dry them.
• Be careful not to damage sliding surfaces and mating surfaces.
• Use lint-free cloth or towels for wiping parts clean. Common shop rags can leave fibers that could interfere

with the operation of the transfer.

DLN-48

< PREPARATION >

[TRANSFER: TY20A]

PREPARATION

PREPARATION

PREPARATION

Special Service Tool

INFOID:0000000009718135

The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.

Tool number
(Kent-Moore No.)
Tool name

Description

KV38101700
(

—

)

Drift
a: 82 mm (3.23 in) dia.
b: 78 mm (3.07 in) dia.

Installing side oil seal (installing adapter case
oil seal)

ST33200000
(J-26082)
Drift
a: 60 mm (2.36 in) dia.
b: 44.5 mm (1.752 in) dia.

• Removing gear ring bearing inner race

(adapter case side)

• Installing companion flange

ST33220000
(J-25804-01)
Drift
a: 37 mm (1.46 in) dia.
b: 31 mm (1.22 in) dia.
c: 22 mm (0.87 in) dia.

Removing drive pinion

ST33061000
(J-8107-2)
Drift
a: 38 mm (1.50 in) dia.
b: 28.5 mm (1.122 in) dia.

Removing gear ring bearing inner race (trans-
fer case side)

KV381054S0
(J-34286)
Puller

• Removing pinion rear bearing outer race
• Removing pinion front bearing outer race
• Removing gear ring oil seal

ST33230000
(J-25805-01)
Drift
a: 51 mm (2.01 in) dia.
b: 41 mm (1.61 in) dia.
c: 28.5 mm (1.122 in) dia.

Installing gear ring oil seal

ZZA1149D

ZZA1002D

ZZA1046D

ZZA0810D

ZZA0601D

ZZA1046D

PREPARATION

DLN-49

< PREPARATION >

[TRANSFER: TY20A]

C

E

F

G

H

I

J

K

L

M

A

B

DLN

N

O

P

ST30720000
(J-25405)
Drift
a: 77 mm (3.03 in) dia.
b: 55.5 mm (2.185 in) dia.

• Installing gear ring bearing outer race

(transfer case side)

• Installing gear ring bearing inner race

(transfer case side)

• Installing gear ring bearing inner race

(adapter case side)

• Installing gear ring bearing outer race

(adapter case side)

• Installing transfer case oil seal

ST27863000
(

—

)

Drift
a: 74.5 mm (2.933 in) dia.
b: 62.5 mm (2.461 in) dia.

Installing gear ring bearing inner race (transfer
case side)

KV40101630
(J-35870)
Drift
a: 68 mm (2.68 in) dia.
b: 60 mm (2.36 in) dia.

Installing gear ring bearing inner race (transfer
case side)

KV38102510
(

—

)

Drift
a: 71 mm (2.80 in) dia.
b: 65 mm (2.56 in) dia.

Installing gear ring bearing inner race (adapter
case side)

KV38100300
(J-25523)
Drift
a: 54 mm (2.13 in) dia.
b: 46 mm (1.81 in) dia.
c: 32 mm (1.26 in) dia.

Installing pinion rear bearing outer race

ST30901000
(J-26010-01)
Drift
a: 79 mm (3.11 in) dia.
b: 45 mm (1.77 in) dia.
c: 35.2 mm (1.386 in) dia.

• Installing pinion front bearing outer race
• Installing pinion front bearing inner race

ST33400001
(J-26082)
Drift
a: 60 mm (2.36 in) dia.
b: 47 mm (1.85 in) dia.

• Installing pinion front bearing outer race
• Installing pinion sleeve oil seal

Tool number
(Kent-Moore No.)
Tool name

Description

ZZA0811D

ZZA1003D

ZZA1003D

ZZA1003D

ZZA1046D

ZZA0978D

ZZA0814D

DLN-50

< PREPARATION >

[TRANSFER: TY20A]

PREPARATION

Commercial Service Tool

INFOID:0000000009718136

ST3127S000
(J-25765-A)
Preload gauge

Measuring preload torque

KV38100200
(

—

)

Drift
a: 65 mm (2.56 in) dia.
b: 49 mm (1.93 in) dia.

Removing transfer case oil seal

KV40101840
(

—

)

Drift
a: 77 mm (3.03 in) dia.
b: 85 mm (3.35 in) dia.

Installing gear ring bearing outer race (transfer
case side)

Tool number
(Kent-Moore No.)
Tool name

Description

ZZA0503D

ZZA1143D

ZZA0881D

Tool name

Description

Power tool

Loosening nuts and bolts and nuts

Drift
a: 89 mm (3.50 in) dia.
b: 72 mm (2.83 in) dia.

Installing gear ring bearing outer race (adapt-
er case side)

Replacer

Removing pinion front bearing inner race

PBIC0190E

NT660

ZZA0700D