Nissan Terrano model r20 series 2004. Manual — part 283
Removal and Installation
I
Remove free-running hub assembly.
Refer to “FRONT AXLE — Auto-Lock Free-running Hub”,
FA-14.
I
Remove brake caliper assembly.
Brake hose does not need to be disconnected from brake
caliper.
Be careful not to depress brake pedal, or piston will pop out.
Make sure brake hose is not twisted.
I
Remove lock washer.
I
Remove wheel bearing lock nut with Tool.
Tool: KV40105400
I
Remove wheel hub and wheel bearing.
Be careful not to drop outer bearing.
I
After installing wheel hub and wheel bearing, adjust wheel
bearing preload.
Refer to “PRELOAD ADJUSTMENT”, “Front Wheel Bearing”,
FA-6.
Disassembly
I
Drive bearing outer races with suitable brass bar.
SFA926
NFA006
NFA007
SFA832
FA858
FRONT AXLE — Wheel Hub and Rotor Disc
FA-18
Inspection
Thoroughly clean wheel bearing and wheel hub.
WHEEL BEARING
I
Make sure wheel bearing rolls freely and is free from noise,
crack, pitting or wear.
WHEEL HUB
I
Check wheel hub for cracks by using a magnetic exploration or
dyeing test.
Assembly
I
Install bearing outer race with Tool until it seats in hub.
I
Pack multi-purpose grease to hub and hub cap.
I
Apply multi-purpose grease to each bearing cone.
I
Pack grease seal lip with multi-purpose grease, then install it
into wheel hub with suitable drift.
YFA010
EFA008
FA781
SFA747
FRONT AXLE — Wheel Hub and Rotor Disc
FA-19
Removal
I
Remove free-running hub assembly.
Refer to “FRONT AXLE — Auto-lock Free-running Hub”, FA-14.
I
Separate drive shaft from knuckle spindle by slightly tapping
drive shaft end.
I
Separate tie-rod from knuckle spindle with Tool.
Install stud nut conversely on stud bolt so as not to damage
stud bolt.
I
Separate knuckle spindle from ball joints.
(1) Loosen (not remove) upper and lower ball joint tightening nuts.
(2) Separate upper and lower ball joints to knuckle spindle with
Tool.
During above operation, never remove ball joint nuts which
are loosened in step (1) above.
Tool: HT72520000
NFA008
NFA009
NFA010
SFA927
SFA079
FRONT AXLE — Knuckle Spindle
FA-20
(3) Remove ball joint tightening nuts.
Support lower link with jack.
(4) Separate knuckle spindle from upper and lower links.
Inspection
KNUCKLE SPINDLE
I
Check knuckle spindle for deformation, cracks or other damage
by using a magnetic exploration or dyeing test.
NEEDLE BEARING
I
Check needle bearing for wear, scratches, pitting, flaking and
burn marks.
Installation
I
Install needle bearing into knuckle spindle.
Make sure that needle bearing is facing in proper direction.
Apply multi-purpose grease.
I
Install knuckle spindle to upper and lower ball joints with lower
link jacked up.
CAUTION:
Make sure that oil or grease does not come into contact with
tapered areas of ball joint and knuckle spindle and threads of
ball joint.
I
After installing knuckle spindle, adjust wheel bearing preload.
Refer to “PRELOAD ADJUSTMENT”, “Front Wheel Bearing”,
FA-6.
I
After installing drive shaft, check drive shaft axial end play.
Do not reuse snap ring once it has been removed.
Temporarily install snap ring at same thickness as it was
installed before removal.
Refer to “FRONT AXLE — Drive Shaft”, FA-22.
NFA011
NFA012
SFA929
NFA013
FRONT AXLE — Knuckle Spindle
Removal (Cont’d)
FA-21
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст