Murano Cross Cabriolet Z51 (2011 year). Manual — part 33
INSTRUMENT PANEL ASSEMBLY
IP-15
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
8.
Remove instrument lower panel LH.
1.
Remove hood opener lever fixing bolts (A).
2.
Pull back instrument lower panel LH (1).
3.
Release data link connector (pawl) then remove it from
instrument lower panel LH.
4.
Disconnect harness connectors and aspirator duct.
9.
Remove driver air bag module. Refer to
SR-11, "Removal and Installation"
.
10. Remove steering wheel. Refer to
ST-32, "Removal and Installation"
.
11. Remove steering column covers.
1.
Remove steering column cover fixing screws (A).
2.
Pull up steering column upper cover (1), and then remove
steering column upper cover.
3.
Pull down steering column lower cover (2), and then remove
steering column lower cover.
12. Remove combination switch. Refer to
BCS-79, "Removal and Installation"
13. Remove spiral cable. Refer to
SR-14, "Removal and Installation"
.
14. Remove cluster lid A.
1.
Pull back cluster lid A (1), and disengage clips and pawl.
2.
Remove cluster lid A.
15. Remove combination meter. Refer to
MWI-79, "Removal and Installation"
: Clip
: Metal clip
JMJIA1316ZZ
: Pawl
JMJIA1317ZZ
: Clip
: Pawl
JMJIA1318ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
IP-16
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
16. Remove cluster lid C (lower).
1.
Disengage cluster lid C (lower) (1) fixing clips and pawls
with remover tool (A).
2.
Pull down cluster lid C (lower).
3.
Disconnect illumination lamp harness connector.
17. Remove instrument stay cover LH.
1.
Remove instrument stay cover LH (1) fixing screw (A).
2.
Disengage instrument stay cover LH fixing clips and pawls
with remover tool.
3.
Pull back and pull up instrument stay cover LH.
4.
Disconnect push button ignition switch harness connector
18. Remove instrument stay cover RH.
1.
Remove instrument stay cover RH (1) fixing screw (A).
2.
Disengage instrument stay cover RH fixing clips and pawls
with remover tool.
3.
Pull back and pull up instrument stay cover RH.
4.
Disconnect hazard switch harness connector.
19. Remove cluster lid D.
1.
Remove cluster lid D (1) fixing screws (A).
2.
Pull back cluster lid D.
3.
Disconnect harness connector.
20. Remove cluster lid C.
1.
Remove cluster lid C (1) fixing screws (A).
2.
Pull back cluster lid C.
3.
Disconnect harness connectors.
: Clip
: Pawl
JMJIA1319ZZ
: Clip
: Pawl
JMJIA1320ZZ
: Clip
: Pawl
JMJIA1321ZZ
: Pawl
JMJIA1322ZZ
JMJIA1323ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
INSTRUMENT PANEL ASSEMBLY
IP-17
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
21. Remove AV control unit. Refer to
AV-113, "Removal and Installation"
.
22. Remove center ventilator assembly.
1.
Remove center ventilator assembly (1) fixing screws (A).
2.
Pull back center ventilator assembly.
23. Remove display unit. Refer to
AV-115, "Removal and Installation"
24. Remove center speaker grille.
1.
Disengage center speaker grille (1) fixing clips with remover
tool (A).
2.
Pull up center speaker grille.
25. Remove center speaker (BOSE audio with NAVI models). Refer to
AV-263, "Removal and Installation"
26. Remove instrument side finisher RH.
1.
Insert a remover tool (A) into lower space.
2.
Pull the instrument side finisher RH (1) crosswise.
27. Remove front body side welt RH. Refer to
INT-21, "BODY SIDE WELT : Removal and Installation"
.
28. Remove front pillar garnish RH. Refer to
INT-18, "FRONT PILLAR GARNISH : Removal and Installation"
29. Remove speaker grille RH.
Pull up speaker grille RH (1).
30. Remove front squawker RH. Refer to
AV-117, "Removal and Installation"
.
31. Remove optical sensor (XENON headlamp models). Refer to
EXL-100, "Removal and Installation"
.
: Clip
: Pawl
JMJIA1325ZZ
: Clip
JMJIA1327ZZ
: Pawl
JMJIA1328ZZ
: Pawl
JMJIA1329ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
IP-18
< REMOVAL AND INSTALLATION >
INSTRUMENT PANEL ASSEMBLY
32. Remove instrument lower panel RH.
1.
Remove instrument lower panel RH (1) fixing screws (A).
2.
Open the glove box lid (2).
3.
Remove instrument lower panel RH fixing screws (B).
4.
Pull back instrument lower panel RH.
5.
Disconnect harness connector.
33. Disconnect front passenger air bag module connector. Refer to
SR-17, "Removal and Installation"
34. Remove front passenger air bag module fixing bolt. Refer to
35. Remove instrument panel assembly (1) mounting screws (A) and bolt (B).
36. Remove instrument panel assembly.
CAUTION:
• Cover center console upper surface with a shop cloth to prevent it from being damaged.
• When removing instrument panel assembly, 2 workers are required so as to prevent it from drop-
ping.
37. Remove the following parts after removing instrument panel assembly.
• Passenger air bag module. Refer to
SR-17, "Removal and Installation"
.
• Ventilator duct. Refer to
VTL-9, "SIDE VENTILATOR GRILLE : Removal and Installation"
.
• Upper ventilator duct. Refer to
VTL-10, "UPPER VENTILATOR DUCT : Removal and Installation"
.
• Defroster nozzle and side defroster nozzle LH/RH. Refer to
VTL-10, "DEFROSTER NOZZLE AND SIDE
DEFROSTER NOZZLE : Removal and Installation"
.
• Side defroster grille LH/RH. Refer to
VTL-9, "SIDE DEFROSTER GRILLE : Removal and Installation"
• Side ventilator grille LH/RH. Refer to
VTL-9, "SIDE VENTILATOR GRILLE : Removal and Installation"
• Antenna feeder
: Pawl
: Metal clip
JMJIA1330ZZ
JMJIA1331ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
INSTRUMENT PANEL ASSEMBLY
IP-19
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
- BOSE audio without navigation: Refer to
- BOSE audio with navigation: Refer to
.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Never use the steering wheel mounting nut after removal, replace with the new nut.
• Never use the driver air bag mounting bolts after removal, replace with the new bolts.
• Never use the passenger air bag mounting bolt after removal, replace with the new bolt.
Revision: 2012 March
2011 Murano CrossCabriolet
IP-20
< REMOVAL AND INSTALLATION >
CENTER CONSOLE ASSEMBLY
CENTER CONSOLE ASSEMBLY
Exploded View
INFOID:0000000006939299
1.
Instrument lower cover RH
2.
Instrument lower cover LH
3.
Instrument stay
4.
Front console bracket
5.
Console reinforcement
6.
Lower console finisher LH
7.
Console harness
8.
Inside key antenna
9.
Console rear finisher
10. Center console assembly
11.
Socket and bulb
12. Console finisher assembly
13. Cup holder assembly
14. Console pocket
15. Socket knob
16. Socket inner case
17. Console mat
18. Console switch finisher
19. Front console pocket
20. Lower console finisher RH
21. USB connector
22. Socket knob
23. Socket ring
24. Socket inner case
25. Lower console assembly
26. Auxiliary input jack
: Pawl
: Clip
: Metal clip
JMJIA6324ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
CENTER CONSOLE ASSEMBLY
IP-21
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
IP
N
O
P
Removal and Installation
INFOID:0000000006939300
CAUTION:
When removing, always use a remover tool that is made of plastic.
REMOVAL
1.
Remove selector lever knob. Refer to
TM-146, "Removal and Installation"
.
2.
Remove console finisher assembly.
1.
Open the console lid.
2.
Remove console finisher assembly (1) fixing pawls and
metal clips with remover tool (A).
3.
Pull up console finisher assembly.
4.
Disconnect harness connectors.
3.
Remove front console pocket.
1.
Remove front console pocket (1) fixing screw (A).
2.
Pull up front console pocket, and then disengage metal
clips.
3.
Disconnect harness connectors.
4.
Remove console rear finisher.
1.
Pull back console rear finisher.
2.
Disconnect harness connector.
5.
Remove center console assembly.
1.
Remove center console assembly (1) fixing screws (A).
2.
Lift up back side and pull back.
: Pawl
: Metal clip
JMJIA1334ZZ
: Metal clip
JMJIA1335ZZ
: Metal clip
JMJIA6325ZZ
JMJIA1338ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
IP-22
< REMOVAL AND INSTALLATION >
CENTER CONSOLE ASSEMBLY
6.
Remove instrument lower cover LH and RH.
1.
Disengage instrument lower cover LH (1) fixing pawls and
clips.
2.
Pull back instrument lower cover LH.
3.
Disengage instrument lower cover RH (2) fixing pawls and
clips.
4.
Pull the instrument lower cover RH crosswise.
7.
Remove lower console finisher LH and RH.
1.
Remove lower console finisher LH (1) fixing screws (A).
2.
Remove lower console finisher LH fixing clip (B).
3.
Remove lower console finisher LH fixing clip (C).
4.
Pull the console finisher LH crosswise.
5.
Remove lower console finisher RH (2) fixing screws (D).
6.
Remove lower console finisher RH fixing clip (E).
7.
Remove lower console finisher RH fixing clip (F).
8.
Pull the console finisher RH crosswise.
8.
Remove lower console assembly.
1.
Remove lower console assembly (1) fixing screws (A).
2.
Remove lower console assembly mounting bolts (B).
3.
Disconnect harness connectors.
NOTE:
Remove following parts after removing lower console assembly.
• USB connector: Refer to
AV-125, "Removal and Installation"
.
• Auxiliary input jacks: Refer to
AV-124, "Removal and Installation"
.
• Console power socket: Refer to
PWO-6, "CONSOLE POWER SOCKET : Removal and Installation"
9.
Remove CVT shift selector. Refer to
TM-146, "Removal and Installation"
.
10. Remove console reinforcement.
1.
Remove console reinforcement (1) mounting nut (A).
2.
Remove console reinforcement mounting bolts (B).
3.
Remove harness clips.
11. Remove instrument stay mounting nuts, and then remove instrument stay.
12. Remove front console bracket mounting bolt and nut, and then remove front console bracket.
INSTALLATION
Install in the reverse order of removal.
: Clip
: Pawl
JMJIA1339ZZ
: Clip
JMJIA1340ZZ
JMJIA1341ZZ
: Clip
JMJIA1342ZZ
Revision: 2012 March
2011 Murano CrossCabriolet
LU-1
ENGINE
C
D
E
F
G
H
I
J
K
L
M
SECTION
LU
A
LU
N
O
P
CONTENTS
ENGINE LUBRICATION SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution for Liquid Gasket . . . . . . . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Special Service Tool . . . . . . . . . . . .....
Commercial Service Tool . . . . . . . . . . ..
SYSTEM DESCRIPTION . . . . . . . ..
DESCRIPTION . . . . . . . . . . . . .
Engine Lubrication System . . . . . . . . . ..
Engine Lubrication System Schematic . . . . . ..
PERIODIC MAINTENANCE . . . . . . ..
ENGINE OIL . . . . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . . ..
Draining . . . . . . . . . . . . . . . . .....
Refilling . . . . . . . . . . . . . . . . .....
OIL FILTER . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
REMOVAL AND INSTALLATION . . . ...
OIL COOLER . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
UNIT DISASSEMBLY AND ASSEMBLY .
OIL PUMP . . . . . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation . . . . . . . . . . .
Disassembly and Assembly . . . . . . . . . .
Inspection . . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
Periodical Maintenance Specification . . . . .
Engine Oil Pressure . . . . . . . . . . . ...
Oil Pump . . . . . . . . . . . . . . . . .
Regulator Valve . . . . . . . . . . . . . ..
Revision: 2012 March
2011 Murano CrossCabriolet
LU-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Liquid Gasket
INFOID:0000000006937848
LIQUID GASKET APPLICATION PROCEDURE
1.
Remove old liquid gasket adhering to the liquid gasket application surface and the mating surface.
• Remove liquid gasket completely from the liquid gasket application surface, mounting bolts, and bolt
holes.
2.
Wipe the liquid gasket application surface and the mating surface with white gasoline (lighting and heating
use) to remove adhering moisture, grease and foreign materials.
3.
Apply liquid gasket to the liquid gasket application surface.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Prod-
.
• Within 5 minutes of liquid gasket application, install in the mating component.
• If liquid gasket protrudes, wipe it off immediately.
• Never retighten mounting bolts or nuts after the installation.
• After 30 minutes or more have passed from the installation, fill engine oil and engine coolant.
Revision: 2012 March
2011 Murano CrossCabriolet
PREPARATION
LU-3
< PREPARATION >
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
PREPARATION
PREPARATION
Special Service Tool
INFOID:0000000006937849
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Commercial Service Tool
INFOID:0000000006937850
Tool number
(Kent-Moore No.)
Tool name
Description
ST25051001
(J-25695-1)
Oil pressure gauge
Measuring oil pressure
Maximum measuring range: 2,452 kPa (25
kg/cm
2
, 356 psi)
ST25052000
(J-25695-2)
Hose
Adapting oil pressure gauge to oil pan (upper)
KV10115801
(J-38956)
Oil filter wrench
Removing oil filter
a: 64.3 mm (2.531 in)
NT050
S-NT559
S-NT375
Tool name
Description
Power tools
Loosening nuts and bolts
PBIC0190E
Revision: 2012 March
2011 Murano CrossCabriolet
LU-4
< PREPARATION >
PREPARATION
Tube presser
Pressing the tube of liquid gasket
Deep socket
Removing and installing oil pressure switch
27 mm (1.06 in)
Tool name
Description
NT052
PBIC4066E
Revision: 2012 March
2011 Murano CrossCabriolet
DESCRIPTION
LU-5
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
SYSTEM DESCRIPTION
DESCRIPTION
Engine Lubrication System
INFOID:0000000006937846
JPBIA1773GB
Revision: 2012 March
2011 Murano CrossCabriolet
LU-6
< SYSTEM DESCRIPTION >
DESCRIPTION
Engine Lubrication System Schematic
INFOID:0000000006937847
JPBIA1775GB
Revision: 2012 March
2011 Murano CrossCabriolet
ENGINE OIL
LU-7
< PERIODIC MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
M
A
LU
N
P
O
PERIODIC MAINTENANCE
ENGINE OIL
Inspection
INFOID:0000000006937851
ENGINE OIL LEVEL
NOTE:
Before starting engine, put vehicle horizontally and check the engine oil level. If engine is already started, stop
it and allow 10 minutes before checking.
1.
Pull out oil level gauge and wipe it clean.
2.
Insert oil level gauge and check the engine oil level is within the
range shown in the figure.
3.
If it is out of range, adjust it.
ENGINE OIL APPEARANCE
• Check engine oil for white turbidity or heavy contamination.
• If engine oil becomes turbid and white, it is highly probable that it is contaminated with engine coolant.
Repair or replace damaged parts.
ENGINE OIL LEAKAGE
Check for engine oil leakage around the following areas:
• Oil pans (lower and upper)
• Oil pan drain plug
• Oil pressure switch
• Oil temperature sensor
• Oil filter
• Water pump cover
• Oil cooler
• Valve timing control covers (bank 1 and bank 2)
• Intake valve timing control solenoid valve (bank 1 and bank 2)
• Mating surface between cylinder head and rocker cover
• Mating surface between front timing chain case and rear timing chain case
• Mating surface between rear timing chain case and cylinder head
• Mating surface between rear timing chain case and cylinder block
• Mating surface between rear timing chain case and oil pan (upper)
• Mating surface between cylinder block and cylinder head
• Crankshaft oil seals (front and rear)
• Camshaft position sensor (PHASE)
OIL PRESSURE CHECK
WARNING:
• Be careful not to get burn yourself, as engine oil may be hot.
• Oil pressure check should be done in “Parking position”.
1.
Check the engine oil level.
2.
Remove splash guard (RH). Refer to
EXT-26, "FENDER PROTECTOR : Exploded View"
.
PBIC4202E
Revision: 2012 March
2011 Murano CrossCabriolet
LU-8
< PERIODIC MAINTENANCE >
ENGINE OIL
3.
Disconnect harness connector at oil pressure switch (2), and
remove oil pressure switch using deep socket (commercial ser-
vice tool).
CAUTION:
Never drop or shock oil pressure switch.
4.
Install the oil pressure gauge [SST: ST25051001 (J-25695-1)]
(A) and hose [SST: ST25052000 (J-25695-2)] (B).
5.
Start the engine and warm it up to normal operating temperature.
6.
Check the engine oil pressure with engine running under no-load.
NOTE:
When the engine oil temperature is low, the engine oil pressure becomes high.
If difference is extreme, check engine oil passage and oil pump for engine oil leakage.
7.
After the inspections, install oil pressure switch as follows:
a.
Remove old liquid gasket adhering to oil pressure switch and the mating surface.
b.
Apply liquid gasket and tighten oil pressure switch to the specification.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-22, "Recommended Chemical Prod-
.
c.
After warming up engine, check there is no leakage of engine oil with running engine.
Draining
INFOID:0000000006937852
WARNING:
• Be careful not to get burn yourself, as engine oil may be hot.
• Prolonged and repeated contact with used engine oil may cause skin cancer. Try to avoid direct skin
contact with used engine oil. If skin contact is made, wash thoroughly with soap or hand cleaner as
soon as possible.
1.
Warm up the engine, and check for engine oil leakage from engine components. Refer to
2.
Stop the engine and wait for 10 minutes.
3.
Loosen oil filler cap.
1
: Oil filter
: Vehicle front
JPBIA1677ZZ
JPBIA0074ZZ
Engine oil pressure
: Refer to
.
Tightening torque
.
Revision: 2012 March
2011 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст