Murano Cross Cabriolet Z51 (2011 year). Manual — part 66
WT-32
< DTC/CIRCUIT DIAGNOSIS >
TIRE PRESSURE RECEIVER
TIRE PRESSURE RECEIVER
Component Function Check
INFOID:0000000006941831
1.
TIRE PRESSURE MONITORING SYSTEM OPERATION
With CONSULT
1.
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or more, then drive normally for 10 minutes.
2.
On “DATA MONITOR”, select “AIR PRESS FL”, “AIR PRESS FR”, “AIR PRESS RR” and “AIR PRESS
RL”, and check that the tire pressures match the standard value.
CAUTION:
Stop the vehicle and within 5 minutes, use CONSULT “DATA MONITOR” to display the tire pressure for
all wheels.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform trouble diagnosis. Refer to
Diagnosis Procedure
INFOID:0000000006941832
1.
CHECK TIRE PRESSURE RECEIVER SIGNAL
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check tire pressure receiver connector and ground signal with oscilloscope.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> GO TO 2.
2.
CHECK TIRE PRESSURE RECEIVER INPUT VOLTAGE
1.
Turn the ignition switch OFF.
2.
Disconnect tire pressure receiver connector.
3.
Turn the ignition switch ON.
Monitor item
Condition
Displayed value
AIR PRESS FL
Drive for 3 minutes at a speed of 40 km/h (25 MPH) or
more, then drive normally for 10 minutes.
Internal pressure of tires
AIR PRESS FR
AIR PRESS RR
AIR PRESS RL
Tire pressure receiver
—
Condition
Voltage
(Approx.)
Connector
Terminal
M21
2
Ground
Stand by state
When receiving the signal from the tire
pressure sensor
OCC3881D
OCC3880D
Revision: 2012 March
2011 Murano CrossCabriolet
TIRE PRESSURE RECEIVER
WT-33
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
CAUTION:
Never start the engine.
4.
Check voltage between tire pressure receiver connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace damaged parts.
3.
CHECK TIRE PRESSURE RECEIVER GROUND CIRCUIT
1.
Turn the ignition switch OFF.
2.
Disconnect BCM harness connector.
3.
Check continuity between BCM harness connector and tire pressure receiver connector.
4.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace damaged parts.
4.
CHECK BCM CIRCUIT
Inspect the BCM circuit. Refer to
.
Is the BCM circuit normal?
YES
>> Replace tire pressure receiver. Refer to
WT-50, "Removal and Installation"
.
NO
>> Replace BCM. Refer to
STC-21, "Removal and Installation"
Tire pressure receiver
—
Voltage
(Approx.)
Connector
Terminal
M21
4
Ground
5.0 V
BCM
Tire pressure receiver
Continuity
Connector
Terminal
Connector
Terminal
M123
137
M21
1
Existed
BCM
—
Continuity
Connector
Terminal
M123
137
Ground
Not existed
Revision: 2012 March
2011 Murano CrossCabriolet
WT-34
< DTC/CIRCUIT DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP
LOW TIRE PRESSURE WARNING LAMP
Component Function Check
INFOID:0000000006941833
1.
CHECK THE ILLUMINATION OF THE LOW TIRE PRESSURE WARNING LAMP
Check that the low tire pressure warning lamp is turned OFF after illuminating for approximately 1 second,
when the ignition switch is turned ON.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Perform trouble diagnosis. Refer to
Diagnosis Procedure
INFOID:0000000006941834
1.
POWER SUPPLY AND GROUND CIRCUIT
Check power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts.
2.
PERFORM SELF-DIAGNOSIS
With CONSULT
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
.
NO
>> GO TO 3.
3.
CHECK LOW TIRE PRESSURE WARNING LAMP SIGNAL
With CONSULT
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Perform “DATA MONITOR” in “AIR PRESSURE MONITOR” of “BCM”.
3.
Select “BCM” in “DATA MONITOR”, and check that the low tire pressure warning lamp is turned OFF after
illuminating for approximately 1 second, when the ignition switch is turned ON.
Is the inspection result normal?
YES
>> Check the combination meter. Refer to
MWI-8, "METER SYSTEM : System Description"
NO
BCS-78, "Removal and Installation"
Revision: 2012 March
2011 Murano CrossCabriolet
POWER SUPPLY AND GROUND CIRCUIT
WT-35
< DTC/CIRCUIT DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
POWER SUPPLY AND GROUND CIRCUIT
Diagnosis Procedure
INFOID:0000000006941835
1.
POWER SUPPLY SYSTEM CHECK
1.
Turn the ignition switch OFF.
2.
Disconnect the BCM harness connector.
3.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
4.
Check the voltage between the BCM harness connector and the ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace damaged parts.
2.
GROUND SYSTEM INSPECTION
1.
Turn the ignition switch OFF.
2.
Check the continuity between the BCM harness connector and the ground.
Is the inspection result normal?
YES
>> • Check the 10A fuse [No. 10 in fuse block (J/B)].
• Check the 40A fusible link [No. L in fuse block].
NO
>> Repair or replace damaged parts.
BCM
—
Voltage
(Approx.)
Connector
Terminal
M118
1
Ground
Battery voltage
M119
11
BCM
—
Continuity
Connector
Terminal
M119
13
Ground
Existed
Revision: 2012 March
2011 Murano CrossCabriolet
WT-36
< SYMPTOM DIAGNOSIS >
TPMS
SYMPTOM DIAGNOSIS
TPMS
Symptom Table
INFOID:0000000006941836
LOW TIRE PRESSURE WARNING LAMP SYMPTOM CHART
Revision: 2012 March
2011 Murano CrossCabriolet
TPMS
WT-37
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
Diagnosis
items
Symptom
(Ignition switch
ON)
Low tire pressure warning lamp
Cause
Action
Low tire pres-
sure warning
lamp
The low tire pres-
sure warning lamp
illuminates for 1
second, then turns
OFF.
Wake-up operation for
all tire pressure sensors
at wheels is completed.
No system malfunctions
The low tire pres-
sure warning lamp
repeats blinking
ON for 2 seconds
and OFF for 0.2
seconds.
Wake-up operation for
all tire pressure sensors
at wheels is not complet-
ed.
Perform the wake-up oper-
ation for all tire pressure
sensors at wheels. Refer to
The low tire pres-
sure warning lamp
blinks once.
The front left tire pres-
sure sensor is not acti-
vated.
Perform the wake-up oper-
ation for the tire pressure
sensor at front left wheel.
Refer to
.
The low tire pres-
sure warning lamp
repeats blinking
twice.
The front right tire pres-
sure sensor is not acti-
vated.
Perform the wake-up oper-
ation for the tire pressure
sensor at front right wheel.
Refer to
.
The low tire pres-
sure warning lamp
repeats blinking
for 3 times.
The rear right tire pres-
sure sensor is not acti-
vated.
Perform the wake-up oper-
ation for the tire pressure
sensor at rear right wheel.
Refer to
.
The low tire pres-
sure warning lamp
repeats blinking
for 4 times.
The rear left tire pres-
sure sensor is not acti-
vated.
Perform the wake-up oper-
ation for the tire pressure
sensor at rear left wheel.
Refer to
.
The low tire pres-
sure warning lamp
turns ON and
stays illuminated.
Low tire pressure
Check the tire pressure for
all wheels and adjust to the
specified value. Refer to
SEIA0592E
SEIA0593E
JPEIC0090GB
SEIA0595E
SEIA0596E
SEIA0597E
SEIA0598E
Revision: 2012 March
2011 Murano CrossCabriolet
WT-38
< SYMPTOM DIAGNOSIS >
TPMS
NOTE:
If tire pressure sensor wake-up operation is not completed for two or more tire pressure sensors, the applica-
ble low tire pressure warning lamp blinking patterns are displayed continuously.
(Example: Blinks once/OFF/blinks 3 times = Wake-up operation is not completed at the front left wheel and
rear right wheel tire pressure sensors.)
Low tire pres-
sure warning
lamp
The low tire pres-
sure warning lamp
repeats blinking at
0.5-second inter-
vals for 1 minute,
and then stays illu-
minated.
The combination meter
fuse is open or removed
(or pulled out).
Check and install the com-
bination meter fuse. If nec-
essary, replace the fuse.
The BCM harness con-
nector is removed.
Check the connection con-
ditions of the BCM harness
connector, and repair if
necessary.
Tire Pressure Monitor-
ing System (TPMS) mal-
function.
• Perform CONSULT self-
10, "AIR PRESSURE
MONITOR : CONSULT
Function (BCM - AIR
PRESSURE MONI-
TOR)"
.
• If necessary, perform tire
pressure sensor ID reg-
istration. Refer to
.
Hazard warn-
ing lamp
The hazard warn-
ing lamp does not
blink twice when
the tire pressure
sensor is activat-
ed.
—
1.
The tire pressure
sensor activation
tool (J-45295)
does not activate.
2.
The ignition switch
is OFF when the
tire pressure sen-
sor wake-up oper-
ation is performed.
3.
The tire pressure
sensor activation
tool (J-45295) is
not used in the cor-
rect position.
4.
The tire pressure
sensor is already
waked up.
1.
Replace the battery in
the tire pressure sen-
sor activation tool (J-
45295).
2.
Turn the ignition
switch ON when per-
forming the tire pres-
sure sensor wake-up
operation.
3.
Operate the tire pres-
sure sensor activation
tool (J-45295) in the
correct position when
performing the wake-
up operation.
4.
No procedure.
Diagnosis
items
Symptom
(Ignition switch
ON)
Low tire pressure warning lamp
Cause
Action
SEIA0788E
Revision: 2012 March
2011 Murano CrossCabriolet
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
WT-39
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN ON
Description
INFOID:0000000006941837
The low tire pressure warning lamp does not illuminate when the ignition switch is turned ON.
NOTE:
The low tire pressure warning lamp illuminates for approximately 1 second and then turns OFF when the igni-
tion switch is turned ON. This is to check that no abnormal condition is present in the tire pressure monitoring
system.
The lamp bulb may be burnt out or the tire pressure monitoring system may be malfunctioning if the low tire
pressure warning lamp does not illuminate when the ignition switch is turned ON.
Diagnosis Procedure
INFOID:0000000006941838
1.
CHECK LOW TIRE PRESSURE WARNING LAMP
Perform trouble diagnosis of the low tire pressure warning lamp. Refer to
Is the inspection result normal?
YES
>> Check pin terminal and connection of each connector for damage and loose connection.
NO
>> Repair or replace damaged parts.
Revision: 2012 March
2011 Murano CrossCabriolet
WT-40
< SYMPTOM DIAGNOSIS >
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF
LOW TIRE PRESSURE WARNING LAMP DOES NOT TURN OFF
Description
INFOID:0000000006941839
The low tire pressure warning lamp does not turn OFF after several seconds is passed after engine starts.
Diagnosis Procedure
INFOID:0000000006941840
1.
CHECK TIRE PRESSURE
1.
Turn the ignition switch ON.
CAUTION:
Never start the engine.
2.
Check the tire pressure for all wheels and adjust to the specified value. Refer to
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Inspect or repair the tires or wheels.
2.
CHECK LOW TIRE PRESSURE WARNING LAMP
Check low tire pressure warning lamp display.
Does not low tire pressure warning lamp turn OFF?
YES
>> GO TO 3.
NO
>> INSPECTION END
3.
CHECK BCM
With CONSULT
Perform “SELF-DIAG RESULTS” in “AIR PRESSURE MONITOR” of “BCM”.
Is any DTC detected?
YES
>> Check the DTC. Refer to
NO
>> GO TO 4.
4.
CHECK BCM POWER SUPPLY AND GROUND CIRCUIT
Perform the trouble diagnosis for power supply and ground circuit. Refer to
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-78, "Removal and Installation"
NO
>> Repair or replace error-detected parts.
Revision: 2012 March
2011 Murano CrossCabriolet
LOW TIRE PRESSURE WARNING LAMP BLINKS
WT-41
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
LOW TIRE PRESSURE WARNING LAMP BLINKS
Description
INFOID:0000000006941841
The low tire pressure warning lamp blinks when the ignition switch is turned ON.
NOTE:
The position of an inactive tire pressure sensor can be identified by checking the blinking timing of the low tire
pressure warning lamp.
Diagnosis Procedure
INFOID:0000000006941842
1.
TIRE PRESSURE SENSOR WAKE-UP OPERATION
Perform the tire pressure sensor wake-up. Refer to
.
Is the tire pressure sensor wake-up completed?
YES
>> GO TO 2.
NO
>> Perform trouble diagnosis for the tire pressure sensor. Refer to
.
2.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
Is tire pressure sensor ID registration completed?
YES
>> INSPECTION END
NO
>> Perform the self-diagnosis for “AIR PRESSURE MONITOR”. Refer to
JPEIC0089GB
Revision: 2012 March
2011 Murano CrossCabriolet
WT-42
< SYMPTOM DIAGNOSIS >
ID REGISTRATION CANNOT BE COMPLETED
ID REGISTRATION CANNOT BE COMPLETED
Description
INFOID:0000000006941843
The ID of the tire pressure sensor installed in each wheel cannot be registered in the tire pressure monitoring
system. Inspect the tire pressure sensor or the tire pressure monitoring system circuit.
Diagnosis Procedure
INFOID:0000000006941844
1.
TIRE PRESSURE SENSOR WAKE-UP
Perform the tire pressure sensor wake-up. Refer to
.
Is the tire pressure sensor wake-up completed?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK TIRE PRESSURE SENSOR ACTIVATION TOOL
Check tire pressure sensor activation tool.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace the battery of tire pressure sensor activation tool or repair/replace the tire pressure sen-
sor activation tool.
3.
TIRE PRESSURE SENSOR ID REGISTRATION
Perform tire pressure sensor ID registration. Refer to
.
CAUTION:
To perform ID registration, observe the following points:
• Never register ID in a place where radio waves are interfered (e.g. radio tower).
• Never register ID in a place close to vehicles including TPMS.
Is tire pressure sensor ID registration completed?
YES
>> INSPECTION END
NO
>> GO TO 4.
4.
CHECK TIRE PRESSURE SIGNAL
Change the work location and perform ID registration again.
NOTE:
Depending on the tire pressure sensor position*, a blind spot exists, and the tire pressure receiver gets a
poor reception. If an ID registration is performed under this condition, the registration may not be completed.
In such case, follow the instructions below to improve the radio wave receiving environment.
• Rotate tire by 90
°
, 180
°
, or 270
°
. (This Step is to change tire pressure sensor position.)
• Open the door close to the tire of which ID registration is ongoing.
*: Radio wave reception condition depends on vehicle architecture (e.g. body harness layout, tire wheel
design) or environment.
When ID registration is performed, which wheels do not react?
All wheels react and ID registration is possible.>>INSPECTION END
Only certain wheel(s) do not react.>>Replace applicable tire pressure sensor. Refer to
All wheels do not react.>>Check the tire pressure receiver. Refer to
Revision: 2012 March
2011 Murano CrossCabriolet
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
WT-43
< SYMPTOM DIAGNOSIS >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
NOISE, VIBRATION AND HARSHNESS (NVH) TROUBLESHOOTING
NVH Troubleshooting Chart
INFOID:0000000006941845
Use chart below to find the cause of the symptom. If necessary, repair or replace these parts.
×
: Applicable
Reference
,
.
—
—
NVH in DLN section.
NVH in DLN section.
NVH in F
AX and FSU sections.
NVH
in
RAX and RSU sections.
Re
fer t
o
T
IRES i
n
t
h
is cha
rt.
Re
fe
r to
ROAD WHEEL
in
th
is ch
art
.
NVH i
n
F
AX,
R
A
X section.
NVH in BR section.
NV
H
in
S
T
s
e
cti
on
.
Possible cause and SUSPECTED PARTS
Imp
rop
er i
ns
ta
lla
ti
o
n,
lo
os
en
es
s
Out
-of-ro
un
d
un
ba
lan
c
e
Incorrect t
ire
pressure
Uneven tire
wear
Def
o
rm
ati
o
n
o
r da
ma
ge
No
n-u
n
if
ormi
ty
In
co
rrec
t t
ire
si
ze
PROPELLER SHAFT
DIFF
ERENTIAL
FRONT A
X
LE
AND FRONT SUSP
ENSION
REAR A
X
LE
AND REAR SUSP
ENSION
TI
RE
S
ROAD WHEE
LS
DRIVE SHAFT
BRAKE
STE
E
RING
Symptom
TIRES
Noise
×
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
×
×
×
Vibration
×
×
×
×
×
×
×
Shimmy
×
×
×
×
×
×
×
×
×
×
×
×
×
Judder
×
×
×
×
×
×
×
×
×
×
×
×
Poor quality ride
or handling
×
×
×
×
×
×
×
×
×
×
ROAD
WHEEL
Noise
×
×
×
×
×
×
×
×
×
×
×
×
Shake
×
×
×
×
×
×
×
×
×
×
×
Shimmy, Judder
×
×
×
×
×
×
×
×
×
Poor quality ride
or handling
×
×
×
×
×
×
×
Revision: 2012 March
2011 Murano CrossCabriolet
WT-44
< PERIODIC MAINTENANCE >
ROAD WHEEL
PERIODIC MAINTENANCE
ROAD WHEEL
Inspection
INFOID:0000000007228100
APPEARANCE
Check the road wheel for bend, damage, crack or wear.
Wheel Balance Adjustment
INFOID:0000000006941846
PREPARATION BEFORE ADJUSTMENT
Using releasing agent, remove double-faced adhesive tape from the road wheel.
CAUTION:
• Be careful not to scratch the road wheel during removal.
• After removing double-faced adhesive tape, wipe clean traces of releasing agent from the road
wheel.
ADJUSTMENT
• The details of the adjustment procedure are different for each model of wheel balancer. Therefore, refer to
each instruction manual.
• If a tire balance machine has adhesion balance weight mode settings and drive-in weight mode setting,
select and adjust a drive-in weight mode suitable for aluminum wheels.
1.
Set road wheel on tire balance machine using the center hole as a guide. Start the tire balance machine.
2.
When inner and outer unbalance values are shown on the tire balance machine indicator, multiply outer
unbalance value by 5/3 to determine balance weight that should be used. Select the outer balance weight
with a value closest to the calculated value above and install to the designated outer position of, or at the
designated angle in relation to the road wheel.
CAUTION:
• Do not install the inner balance weight before installing the outer balance weight.
• Before installing the balance weight, be sure to clean the mating surface of the road wheel.
a.
Indicated unbalance value
×
5/3 = balance weight to be installed
Calculation example:
23 g (0.81 oz)
×
5/3 = 38.33 g (1.35 oz)
⇒
40 g (1.41 oz) balance
weight (closer to calculated balance weight value)
NOTE:
Note that balance weight value must be closer to the calculated
balance weight value.
Example:
37.4
⇒
35 g (1.23 oz)
37.5
⇒
40 g (1.41 oz)
b.
Installed balance weight in the position.
SMA054D
Revision: 2012 March
2011 Murano CrossCabriolet
ROAD WHEEL
WT-45
< PERIODIC MAINTENANCE >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
• When installing balance weight (1) to road wheels, set it into
the grooved area (A) on the inner wall of the road wheel as
shown in the figure so that the balance weight center (B) is
aligned with the tire balance machine indication position
(angle) (C).
CAUTION:
• Always use genuine NISSAN adhesion balance weights.
• Balance weights are non-reusable; always replace with
new ones.
• Do not install more than three sheets of balance weight.
c.
If calculated balance weight value exceeds 50 g (1.76 oz), install
two balance weight sheets in line with each other as shown in
the figure.
CAUTION:
Do not install one balance weight sheet on top of another.
3.
Start the tire balance machine again.
4.
Install drive-in balance weight on inner side of road wheel in the
tire balance machine indication position (angle).
CAUTION:
Do not install more than two balance weight.
5.
Start the tire balance machine. Make sure that inner and outer
residual unbalance values are 5 g (0.17 oz) each or below.
CAUTION:
If either residual unbalance value exceeds limit, repeat installation procedures.
Tire Rotation
INFOID:0000000007228102
• Follow the maintenance schedule for tire rotation service intervals.
MA-4, "Explanation of General Maintenance"
.
• When installing the wheel, tighten wheel nuts to the specified
.
CAUTION:
• Do not include the T-type spare tire when rotating the tires.
• When installing wheels, tighten them diagonally by dividing
the work two to three times in order to prevent the wheels
from developing any distortion.
• Be careful not to tighten wheel nut at torque exceeding the
criteria for preventing strain of disc rotor.
• Use NISSAN genuine wheel nuts for aluminum wheels.
• Perform the ID registration, after tire rotation. Refer to
JPEIC0040ZZ
Limit
Dynamic (At flange):
Refer to
.
Static (At flange):
Refer to
.
PEIA0033E
SMA829C
Revision: 2012 March
2011 Murano CrossCabriolet
WT-46
< REMOVAL AND INSTALLATION >
ROAD WHEEL TIRE ASSEMBLY
REMOVAL AND INSTALLATION
ROAD WHEEL TIRE ASSEMBLY
Exploded View
INFOID:0000000006941847
Removal and Installation
INFOID:0000000006941848
REMOVAL
1.
Remove wheel nuts.
2.
Remove tire assembly.
INSTALLATION
Note the following, install in the reverse order of removal.
• When replacing or rotating wheels, perform the ID registration. Refer to
.
Inspection
INFOID:0000000006941849
ALUMINUM WHEEL
1.
Check tires for wear and improper inflation.
2.
Check wheels for deformation, cracks and other damage. If deformed, remove wheel and check wheel
runout.
a.
Remove tire from aluminum wheel and mount on a tire balance machine.
b.
Set dial indicator as shown in the figure.
c.
Check runout, If the axial runout (A) or radial runout (B) exceeds
the limit, replace aluminum wheel.
1.
Tire assembly
: N·m (kg-m, ft-lb)
JSGIA0639GB
Limit
Axial runout (A)
: Refer to
.
Radial runout (B)
: Refer to
.
SEIA0737E
Revision: 2012 March
2011 Murano CrossCabriolet
ROAD WHEEL TIRE ASSEMBLY
WT-47
< REMOVAL AND INSTALLATION >
C
D
F
G
H
I
J
K
L
M
A
B
WT
N
O
P
How to Handle Puncture Repair Agent
INFOID:0000000007227046
CAUTION:
• Never spill the sealant in the tire during repair.
• If the sealant spills, wipe it out with a waste cloth.
• Never reuse the repair kit hose used for a temporary repair of a flat tire because some of the punc-
ture repair agent remains in the hose.
• After using a puncture repair agent, replace tire pressure sensor with a new one.
1.
Remove tires from the vehicle.
2.
Remove tire from road wheel, using a tire changer.
CAUTION:
• When deflating a tire, cover the tire pressure sensor with a waste cloth to prevent the sealant
from splattering.
• Never spill the sealant in the tire during repair.
3.
Dispose of sealant in the removed tire.
CAUTION:
• Wipe out sealant spilled on the road wheel, tire, tire changer, and floor with a waste cloth.
• Drained sealant or expired sealant returned by the customer must be disposed according to the
law and local regulations.
• Fix a tire blowout, if repairable.
NOTE:
Sealant blocks holes caused by blowouts. These holes may not be found and repaired, depending on
the level of blowout. Therefore, it is necessary to check tire air pressure frequently and replace tire with
a new one, if the air pressure is decreasing.
• Replace tire with a new one, if not repairable.
CAUTION:
Never dispose of tires with the sealant contained.
Revision: 2012 March
2011 Murano CrossCabriolet
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст