Juke F15 (2012 year). Service Repair Manual — part 76
DLK-208
< SYSTEM DESCRIPTION >
[TYPE 2]
SYSTEM (INTELLIGENT KEY SYSTEM)
BACK DOOR OPEN FUNCTION : System Diagram
INFOID:0000000006659782
BACK DOOR OPEN FUNCTION : System Description
INFOID:0000000006659783
While back door open in the permitted state, back door opens when back door opener switch is pressed after
back door opener request switch is operated.
BACK DOOR OPEN
• When the BCM detects that back door opener switch is pressed, it starts the outside key antenna (rear
bumper) and inside key antenna and transmits the request signal to the Intelligent Key. Then, check that the
Intelligent Key is near the back door.
• If the Intelligent Key is within the outside key antenna detection area, it receives the request signal and
transmits the key ID signal to the BCM via remote keyless entry receiver.
• BCM receives the key ID signal and compares it with the registered key ID.
• BCM opens back door, simultaneously unlocks all doors.
NOTE:
In anti-hijack mode, only back door opens. All doors do not unlock.
OPERATION CONDITION
If the following conditions are satisfied, the back door can be opened.
OUTSIDE KEY ANTENNA DETECTION AREA
The outside key antenna detection area of back door open function
is in the range of approximately 80 cm (31.50 in) surrounding the
back door opener switch (1). However, this operating range depends
on the ambient conditions.
LIST OF OPERATION RELATED PARTS
Parts marked with
×
are the parts related to operation.
JMKIA6136GB
Back door open function
Operation condition
Back door open operation
• Vehicle speed is less than 5 km/h (3 MPH)
• 3 seconds or more after BCM outputs all doors lock signal
• Intelligent Key is outside of vehicle
• Intelligent Key is within outside key antenna detection area
JMKIA5804ZZ
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-209
< SYSTEM DESCRIPTION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY FUNCTION
REMOTE KEYLESS ENTRY FUNCTION : System Diagram
INFOID:0000000006551572
REMOTE KEYLESS ENTRY FUNCTION : System Description
INFOID:0000000006551573
The Intelligent Key has the same functions as the remote control entry system. Therefore, it can be used in the
same manner as the remote controller by operating the door lock/unlock button.
OPERATION
Remote keyless entry system controls operation of the following items.
• Door lock/unlock
• Anti-hijack function
• Hazard reminder function
• Auto door lock
OPERATION AREA
To check that the Intelligent Key works normally, use within 1 m (3 ft) range of each doors, however the opera-
ble range may differ according to surroundings.
DOOR LOCK/UNLOCK FUNCTION
• When door lock/unlock button of the Intelligent Key is pressed, lock signal or unlock signal transmitted from
Intelligent Key to BCM via remote keyless entry receiver.
• BCM receives the signal and compares it with the registered key ID to the vehicle.
• BCM transmits door lock/unlock signal to each door lock actuator and operates each door lock actuator,
when key ID matches. At the same time, BCM blinks hazard warning lamps (lock: 1 time, unlock: 2 times).
OPERATION CONDITION
If the following condition are satisfied, remote keyless entry operation is performed when the Intelligent Key is
operated.
Door lock function
In
te
llige
n
t Key
Re
mo
te
ke
yl
es
s en
try rec
e
iv
e
r
Ba
ck
do
or op
en
er a
c
tu
a
tor
Do
or loc
k
ac
tu
ato
r
In
si
de
ke
y an
ten
n
a
Out
s
id
e ke
y a
n
ten
n
a
CAN co
mm
un
ic
ati
o
n
s
y
s
tem
BC
M
Ba
ck
do
or op
en
er s
w
it
c
h
Combination meter
Back door open function
×
×
×
×
×
×
×
×
×
×
JMKIA6009GB
DLK-210
< SYSTEM DESCRIPTION >
[TYPE 2]
SYSTEM (INTELLIGENT KEY SYSTEM)
ANTI-HIJACK FUNCTION
• When an LOCK signal is transmitted from Intelligent Key, all doors are locked.
• When an UNLOCK signal is transmitted from Intelligent Key once, driver side door is unlocked.
• Then, if an UNLOCK signal is transmitted from Intelligent Key again within 5 seconds, all other doors (except
for back door) are unlocked.
AUTO DOOR LOCK FUNCTION
After door is unlocked by Intelligent Key button operation and if 30 seconds or more passes without performing
the following operation, all doors are locked. However, operation check function does not activate.
Auto door lock mode can be changed by the “AUTO LOCK SET” mode in “WORK SUPPORT”. Refer to
219, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY) (Without Super Lock)"
HAZARD REMINDER FUNCTION
When doors are locked or unlocked by Intelligent Key, BCM blinks hazard warning lamps as a reminder.
Setting of Hazard Reminder Mode
LIST OF OPERATION RELATED PARTS
Parts marked with
×
are the parts related to operation.
Remote controller operation
Operation condition
Lock
• All doors closed
• Ignition switch in the OFF position
• P position warning is not activated
Unlock
• Ignition switch is in the OFF position
• Intelligent Key is outside the vehicle
• P position warning is not activated
Operating condition
• Door switch is ON (door is open)
• Door is locked
• Push switch is pressed
Hazard reminder setting
(With CONSULT-III)
Door lock operation
(with Intelligent Keyfob)
Hazard warning lamp blink
HAZARD ANSWER BACK
OFF
Any
—
LOCK ONLY
Lock
Once
Unlock
—
Unlock (Anti-hijack)
—
UNLK ONLY
Lock
—
Unlock
Twice
Unlock (Anti-hijack)
Twice (quick)
LOCK/UNLK
Lock
Once
Unlock
Twice
Unlock (Anti-hijack)
Twice (quick)
Remote keyless entry functions
In
tel
ligen
t K
e
y
Do
or swi
tch
Do
or lo
ck
ac
tu
at
o
r
Pu
sh
-bu
tto
n i
g
n
iti
on
swi
tch
CAN communication
system
BCM
Com
b
ina
tio
n me
ter
Hazard warning
lamp
Door lock/unlock function by remote control button
×
×
×
×
×
Hazard reminder function
×
×
×
×
×
×
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-211
< SYSTEM DESCRIPTION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
KEY REMINDER FUNCTION
KEY REMINDER FUNCTION : System Diagram
INFOID:0000000006551574
KEY REMINDER FUNCTION : System Description
INFOID:0000000006551575
Key reminder is the function that prevents the key from being left in the vehicle.
Key reminder has the following 4 functions.
Anti-hijack function
×
×
×
×
×
×
Auto door lock function
×
×
×
Remote keyless entry functions
In
te
lli
gen
t K
e
y
Do
or swi
tch
Do
or lo
ck
ac
tu
at
o
r
Pu
sh
-bu
tto
n i
g
n
iti
on
swi
tch
CAN c
o
m
m
uni
ca
tio
n
sy
st
em
BCM
Com
b
ina
tio
n me
ter
Hazard warning
lamp
JMKIA6138GB
Key remainder func-
tion
Operation condition
Operation
Driver side door
opened
Right after door is locked by door lock/unlock switch or driver door lock
knob operation under the following conditions
• Ignition switch is in the OFF position
• Intelligent Key is inside the vehicle
• Driver side door is opened
All doors unlock
Driver side door
closed*
Right after driver side door is closed under the following conditions
• Intelligent Key is inside the vehicle
• Driver side door is opened
• Driver side door is in unlock state
All doors unlock
Door is open or closed
Right after all doors are closed under the following conditions
• Intelligent Key is inside the vehicle
• Any door is opened
• All doors are locked.
• All doors unlock
• Honk Intelligent Key warn-
ing buzzer
Back door is closed
Right after back door is closed under the following conditions
• Intelligent Key is inside the vehicle
• All doors (except back door) are closed
• All doors (except back door) are locked
• All doors unlock
• Back door can open with
back door opener switch
• Honk Intelligent Key warn-
ing buzzer
DLK-212
< SYSTEM DESCRIPTION >
[TYPE 2]
SYSTEM (INTELLIGENT KEY SYSTEM)
*:If the door closing impact shocks the door lock knob, or contacts against baggage with the door lock knob might activate the door locks
accidentally but unlock operation is perform in these cases.
CAUTION:
• The above function operates when the Intelligent Key is inside the vehicle. However, there may be
times when the Intelligent Key cannot be detected, and this function does not operate when the Intel-
ligent Key is on the instrument panel, rear parcel shelf, or in the glove box. Also, this system some-
times does not operate if the Intelligent Key is in the door pocket for the open door.
WARNING FUNCTION
WARNING FUNCTION : System Description
INFOID:0000000006551576
OPERATION DESCRIPTION
The warning function are as per the following items and are given to the user as warning information and
warnings using combinations of Intelligent Key warning buzzer, combination meter buzzer, KEY warning lamp,
shift P warning lamp and engine start operation indicator lamp.
• Intelligent Key system malfunction
• OFF position warning
• P position warning
• ACC warning
• Take away warning
• Door lock operation warning
• Engine start information
• Intelligent Key low battery warning
• Key ID warning
OPERATION CONDITION
Operation condition of warning and information is as per the following table.
Warning/Information functions
Operation procedure
Intelligent Key system malfunction
A malfunction is detected on BCM and key warning lamp turns ON
OFF position warning
For internal
• Ignition switch: ACC position
• Door switch (driver side): ON (Door is open)
For external*
OFF position warning (For internal) is in active mode, driver side door is closed
NOTE:
OFF position warning (for external) operates only when driver door is closed af-
ter each of P position warning, ACC warning, and OFF position warning (inter-
nal) sounds.
P position warning*
For internal
• Shift position: Except P position
• Engine is running to stopped (Ignition switch is ON to OFF)
For external
• P position warning (For internal) operates
• Door switch: ON to OFF (Door is open to close)
• Intelligent Key cannot be detected inside the vehicle
ACC warning*
• After P position warning operates, or when ignition switch is turned ON imme-
diately after P position warning operates
• Ignition switch: ACC position
Take away warning
Door status changes
from open to close
• Ignition switch: Except LOCK position
• Door switch: ON to OFF (Door is open to close)
• Registered Intelligent Key is not detected inside the vehicle
Door status is open
• Door switch: ON (Door is open)
• Registered Intelligent Key is not detected inside the vehicle during Key ID ver-
ification for 5 seconds
Push button-ignition
switch operation
• Ignition switch: Except LOCK position
• Press push-button ignition switch
• Registered Intelligent Key is not detected inside the vehicle
Door lock operation warning
When door lock operation is requested while door lock operating condition of
door request switch not satisfied
SYSTEM (INTELLIGENT KEY SYSTEM)
DLK-213
< SYSTEM DESCRIPTION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
*: M/T models do not apply.
WARNING METHOD
The following table shows the alarm or warning methods with chime.
*: M/T models do not apply.
LIST OF OPERATION RELATED PARTS
Parts marked with
×
are the parts related to operation.
Engine start information
Ignition switch is ON po-
sition
• Ignition switch: ON position
• Shift position: P position*
• Engine is stopped
Ignition switch is except
ON position
• Ignition switch: Except ON position
• Shift position: P position*
• Intelligent Key can be detected inside the vehicle
Intelligent Key low battery warning
BCM detects that Intelligent Key is low battery, after ignition switch is turned ON
Key ID warning
• Push-button ignition switch is pressed
• Registered Intelligent Key is not detected inside the vehicle
Warning/Information functions
Operation procedure
Warning/Information functions
“KEY” warn-
ing lamp
Shift P
warning
lamp
Warning chime
Engine start
operation in-
dicator lamp
Combination
meter buzzer
Intelligent
Key warning
buzzer
Intelligent Key system malfunction
Indicate
—
—
—
—
OFF position warning
For internal
—
—
Activate
—
—
For external*
—
—
—
Activate
—
P position warning*
For internal
Blink (yellow)
Indicate
Activate
—
—
For external
—
—
Active
—
ACC warning*
—
—
Activate
—
—
Take away warning
Door is open to close
Blink (yellow)
—
Activate
Activate
—
Door is open
—
—
—
—
Push-ignition switch opera-
tion
—
Activate
—
—
Door lock operation warning
—
—
—
Activate
—
Key ID warning
Blink (yellow)
—
—
—
—
Engine start information
—
—
—
—
Indicate
Intelligent Key low battery warning
Blink (green)
—
—
—
—
Warning function
In
te
lli
gen
t K
e
y
Ig
ni
tio
n
switch
Do
or swi
tch
Doo
r re
qu
es
t s
w
itc
h
In
si
de
ke
y an
ten
n
a
O
u
tsi
d
e
ke
y
an
ten
n
a
In
te
lli
gen
t K
e
y warn
in
g b
u
zze
r
Co
mbi
n
at
io
n
m
e
te
r wa
rn
in
g
b
u
zz
er
CAN communication
system
BCM
Sh
if
t P wa
rnin
g
lam
p
En
gi
ne st
art ope
rat
ion
i
n
d
ica
to
r
la
mp
“KEY
” warning lamp
Intelligent Key system malfunction
×
×
×
OFF position warning
For internal
×
×
×
×
For external
×
×
×
DLK-214
< SYSTEM DESCRIPTION >
[TYPE 2]
SYSTEM (INTELLIGENT KEY SYSTEM)
P position warning
×
×
×
×
×
×
ACC warning
×
×
×
×
Take away warning
Door is open or close
×
×
×
×
×
×
×
×
Door is open
×
×
×
×
×
×
Push-button ignition switch opera-
tion
×
×
×
×
×
×
×
Door lock operation warning
×
×
×
×
×
×
×
Key ID warning
×
×
×
×
×
Engine start informa-
tion
Ignition switch is ON position
×
×
×
×
×
×
Ignition switch is except ON posi-
tion
×
×
×
×
×
×
Steering lock information
×
×
×
Intelligent Key low battery warning
×
×
×
×
×
Warning function
Int
e
llig
en
t Ke
y
Ig
ni
ti
o
n
swi
tch
Doo
r swi
tch
Do
or re
qu
es
t s
w
it
c
h
In
si
de
k
e
y
an
te
nn
a
Ou
ts
id
e
ke
y an
ten
n
a
Int
e
llig
en
t Ke
y
wa
rni
n
g
bu
zze
r
Com
b
inat
io
n m
e
te
r wa
rnin
g
bu
zz
er
CAN co
mm
un
ic
ati
o
n
sy
stem
BCM
Shi
ft P
warning l
a
mp
En
gi
ne
st
art
op
era
tio
n i
n
d
ic
a
to
r
la
mp
“KEY” warni
n
g lamp
BACK DOOR OPENER SYSTEM
DLK-215
< SYSTEM DESCRIPTION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR OPENER SYSTEM
System Diagram
INFOID:0000000006554240
System Description
INFOID:0000000006554241
BACK DOOR OPENER OPERATION
When back door opener switch is pressed, BCM operates back door opener actuator.
NOTE:
Back door opener actuator is not for locking the back door. The function is only to open the back door.
OPERATION CONDITION
If the following conditions are satisfied, back door opener operation is performed.
NOTE:
• When battery terminal is disconnected and reconnected during all doors unlock state, back door may not
open.
• Regardless of door lock actuator state, BCM resets recognition of all doors unlock state approximately 30
seconds after battery terminal is disconnected and BCM recognizes that all doors are in lock state.
• When battery terminal is reconnected and back door does not open, have BCM recognize that all doors are
in unlock state.
JMKIA6011GB
Back door opener switch operation
Operation condition
Back door open
• When back door is unlocked using back door opener request switch (anti-hijack
mode), or after BCM outputs all doors unlock signal
• Vehicle speed is less than 5 km/h (3 MPH)
DLK-216
< SYSTEM DESCRIPTION >
[TYPE 2]
DIAGNOSIS SYSTEM (BCM)
DIAGNOSIS SYSTEM (BCM)
COMMON ITEM
COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)
INFOID:0000000006748144
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.
×
: Applicable item
NOTE:
• *1: This item is displayed, but not used.
• *2: For models with automatic A/C, this diagnosis mode is not used.
FREEZE FRAME DATA (FFD)
Diagnosis mode
Function Description
Work Support
Changes the setting for each system function.
Self Diagnostic Result
Displays the diagnosis results judged by BCM.
CAN Diag Support Monitor
Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.
Data Monitor
The BCM input/output signals are displayed.
Active Test
The signals used to activate each device are forcibly supplied from BCM.
Ecu Identification
The BCM part number is displayed.
Configuration
• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.
System
Sub system selection item
Diagnosis mode
Work Support
Data Monitor
Active Test
Door lock
DOOR LOCK
×
×
×
Rear window defogger
REAR DEFOGGER
×
×
Warning chime
BUZZER
×
×
Interior room lamp timer
INT LAMP
×
×
×
Exterior lamp
HEAD LAMP
×
×
×
Wiper and washer
WIPER
×
×
×
Turn signal and hazard warning lamps
FLASHER
×
×
×
• Automatic A/C
• Manual A/C
AIR CONDITONER
×
×
*
2
• Intelligent Key system
• Engine start system
INTELLIGENT KEY
×
×
×
Combination switch
COMB SW
×
Body control system
BCM
×
NVIS - NATS
IMMU
×
×
×
Interior room lamp battery saver
BATTERY SAVER
×
×
×
Back door open
TRUNK
×
Theft warning alarm
THEFT ALM
×
×
×
—
RETAINED PWR*
1
×
Signal buffer system
SIGNAL BUFFER
×
×
DIAGNOSIS SYSTEM (BCM)
DLK-217
< SYSTEM DESCRIPTION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT-III.
DOOR LOCK
DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)
INFOID:0000000006548665
BCM CONSULT-III FUNCTION
CONSULT-III performs the following functions via CAN communication with BCM.
WORK SUPPORT
CONSULT screen item
Indication/Unit
Description
Vehicle Speed
km/h
Vehicle speed of the moment a particular DTC is detected
Odo/Trip Meter
km
Total mileage (Odometer value) of the moment a particular DTC is detected
Vehicle Condition
SLEEP>LOCK
Power position status of
the moment a particular
DTC is detected
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “LOCK”)
SLEEP>OFF
While turning BCM status from low power consumption mode to
normal mode (Power supply position is “OFF”.)
LOCK>ACC
While turning power supply position from “LOCK” to “ACC”
ACC>ON
While turning power supply position from “ACC” to “IGN”
RUN>ACC
While turning power supply position from “RUN” to “ACC” (Vehicle
is stopping and selector lever is except P position.)
CRANK>RUN
While turning power supply position from “CRANKING” to “RUN”
(From cranking up the engine to run it)
RUN>URGENT
While turning power supply position from “RUN“ to “ACC” (Emer-
gency stop operation)
ACC>OFF
While turning power supply position from “ACC” to “OFF”
OFF>LOCK
While turning power supply position from “OFF” to “LOCK”
OFF>ACC
While turning power supply position from “OFF” to “ACC”
ON>CRANK
While turning power supply position from “IGN” to “CRANKING”
OFF>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “OFF”.) to low power consumption mode
LOCK>SLEEP
While turning BCM status from normal mode (Power supply posi-
tion is “LOCK”.) to low power consumption mode
LOCK
Power supply position is “LOCK” (Ignition switch OFF with steer-
ing is locked.)
OFF
Power supply position is “OFF” (Ignition switch OFF with steering
is unlocked.)
ACC
Power supply position is “ACC” (Ignition switch ACC)
ON
Power supply position is “IGN” (Ignition switch ON with engine
stopped)
ENGINE RUN
Power supply position is “RUN” (Ignition switch ON with engine
running)
CRANKING
Power supply position is “CRANKING” (At engine cranking)
IGN Counter
0 - 39
The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1
→
2
→
3...38
→
39 after returning to the normal condition
whenever ignition switch OFF
→
ON.
• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.
DLK-218
< SYSTEM DESCRIPTION >
[TYPE 2]
DIAGNOSIS SYSTEM (BCM)
*: P range interlock door lock can be selected for M/T models, but automatic door lock/unlock function does not operate.
DATA MONITOR
ACTIVE TEST
Monitor item
Description
DOOR LOCK-UNLOCK SET
Anti-hijack function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
AUTOMATIC DOOR LOCK SE-
LECT
Automatic door lock function mode can be selected from the following in this mode
• VH SPD: All doors are locked when vehicle speed more than 10 km/h (6 MPH)
• P RANGE*: All doors are locked when shifting the selector lever from P position to other than
the P position
AUTOMATIC DOOR UNLOCK
SELECT
Automatic door unlock function mode can be selected from the following in the mode
• MODE 1: All doors are unlocked when the power supply position is changed from ON to OFF
• MODE 2*: All doors are unlocked when shifting the selector lever from any position other than
the P to P position
• MODE 3: Driver side door is unlocked when the power supply position is changed from ON to
OFF
• MODE 4*: Driver side door is unlocked when shifting the selector lever from any position other
than the P to P position
• MODE 5: This item is displayed, but cannot be monitored
• MODE 6: This item is displayed, but cannot be monitored
AUTOMATIC LOCK/UNLOCK
SET
Automatic door lock/unlock function mode can be selected from the following in this mode
• Off: Non-operational
• Unlock Only: Door unlock operation only
• Lock Only: Door lock operation only
• Lock/Unlock: Lock and unlock operation
Monitor Item
Contents
REQ SW-DR
Indicated [On/Off] condition of door request switch (driver side)
REQ SW-AS
Indicated [On/Off] condition of door request switch (passenger side)
REQ SW-BD/TR
Indicated [On/Off] condition of back door request switch
DOOR SW-DR
Indicated [On/Off] condition of front door switch (driver side)
DOOR SW-AS
Indicated [On/Off] condition of front door switch (passenger side)
DOOR SW-RR
Indicated [On/Off] condition of rear door switch RH
DOOR SW-RL
Indicated [On/Off] condition of rear door switch LH
DOOR SW-BK
Indicated [On/Off] condition of back door switch
CDL LOCK SW
Indicated [On/Off] condition of lock signal from door lock unlock switch
CDL UNLOCK SW
Indicated [On/Off] condition of unlock signal from door lock unlock switch
KEY CYL LK-SW
NOTE:
This item is displayed, but cannot be monitored
KEY CYL UN-SW
NOTE:
This item is displayed, but cannot be monitored
SHOCK SENSOR
Indicates [NOMAL/ON/OFF] condition of circuit between BCM and air bag diagnosis sensor unit
• NORMAL: Ignition switch ON. (BCM is receiving normal condition signal from air bag diagnosis sensor
unit.)
• ON: During the receiving of air bag signal from air bag diagnosis sensor unit
• OFF: After the receiving of air bag signal from air bag diagnosis sensor unit
DIAGNOSIS SYSTEM (BCM)
DLK-219
< SYSTEM DESCRIPTION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
*: BD UNLK function does not operate.
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY) (Without Su-
per Lock)
INFOID:0000000006548666
WORK SUPPORT
Test item
Description
DOOR LOCK
This test is able to check door lock/unlock operation
• The all door lock actuators are locked when “ALL LOCK” on CONSULT-III screen is touched
• The all door lock actuators are unlocked when “ALL UNLK” on CONSULT-III screen is touched
• The door lock actuator (driver side) is unlocked when “DR UNLK” on CONSULT-III screen is
touched
• The back door lock actuator is unlocked when “BD UNLK” on CONSULT- III screen is touched*
• The door lock actuator (other) is unlocked when “OTR ULK” on CONSULT-III screen is touched
SUPER LOCK
NOTE:
This item is displayed, but cannot be monitored
DOOR LOCK IND
NOTE:
This item is displayed, but cannot be monitored
Monitor item
Description
INSIDE ANT DIAGNOSIS
This function allows inside key antenna self-diagnosis
LOCK/UNLOCK BY I-KEY
Door lock/unlock function by door request switch mode can be changed to operation in this
mode
• On: Operate
• Off: Non-operation
ENGINE START BY I-KEY
Engine start function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
TRUNK/GLASS HATCH OPEN
NOTE:
This item is displayed, but cannot be monitored
PANIC ALARM SET
NOTE:
This item is displayed, but cannot be monitored
TRUNK OPEN DELAY
NOTE:
This item is displayed, but cannot be monitored
LO- BATT OF KEY FOB WARN
Intelligent Key low battery warning mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
ANTI KEY LOCK IN FUNCTI
Key reminder function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
HAZARD ANSWER BACK
Hazard reminder function mode by door request switch and Intelligent Key button can be se-
lected from the following with this mode
• Lock Only: Door lock operation only
• Unlock Only: Door unlock operation only
• Lock/Unlock: Lock and unlock operation
• Off: Non-operation
ANS BACK I-KEY LOCK
Buzzer reminder function (lock operation) mode by door request switch can be selected from
the following with this mode
• Horn Chirp: Sound horn
• Buzzer: Sound Intelligent Key warning buzzer
• Off: Non-operation
ANS BACK I-KEY UNLOCK
Buzzer reminder function (unlock operation) mode by door request switch can be changed to
operation with this mode
• On: Operate
• Off: Non-operation
DLK-220
< SYSTEM DESCRIPTION >
[TYPE 2]
DIAGNOSIS SYSTEM (BCM)
SELF-DIAG RESULT
DATA MONITOR
SHORT CRANKING OUTPUT
Starter motor can operate during the times below
• 70 msec
• 100 msec
• 200 msec
CONFIRM KEY FOB ID
It can be checked whether Intelligent Key ID code is registered or not in this mode
AUTO LOCK SET
Auto door lock operation time can be changed in this mode
• MODE 1: OFF
• MODE 2: 30 sec
• MODE 3: 1 minute
• MODE 4: 2 minutes
• MODE 5: 3 minutes
• MODE 6: 4 minutes
• MODE 7: 5 minutes
ANSWER BACK FUNCTION
Buzzer reminder function mode by Intelligent Key button can be selected from the following
with this mode
• On: Operate
• Off: Non-operation
TAKE OUT FROM WIN WARN SET
NOTE:
This item is indicated, but not used
RETRACTABLE MIRROR SET
Auto retractable door mirror function mode can be changed to operation with this mode
• On: Operate
• Off: Non-operation
Monitor item
Description
Monitor Item
Condition
REQ SW -DR
Indicates [On/Off] condition of door request switch (driver side)
REQ SW -AS
Indicates [On/Off] condition of door request switch (passenger side)
REQ SW -BD/TR
Indicates [On/Off] condition of back door request switch
PUSH SW
Indicates [On/Off] condition of push-button ignition switch
CLUTCH SW*
1
Indicates [On/Off] condition of clutch interlock switch
BRAKE SW 1
Indicates [On/Off]*
2
condition of stop lamp switch power supply
BRAKE SW 2
Indicates [On/Off] condition of stop lamp switch
DETE/CANCL SW
Indicates [On/Off] condition of P position
SFT PN/N SW
Indicates [On/Off] condition of P or N position
S/L -LOCK
Indicates [On/Off] condition of steering lock unit (LOCK)
S/L -UNLOCK
Indicates [On/Off] condition of steering lock unit (UNLOCK)
S/L RELAY -F/B
Indicates [On/Off] condition of steering lock relay
UNLK SEN -DR
Indicates [On/Off] condition of driver door UNLOCK status
PUSH SW -IPDM
Indicates [On/Off] condition of push-button ignition switch
IGN RLY1 -F/B
Indicates [On/Off] condition of ignition relay 1
DETE SW -IPDM
Indicates [On/Off] condition of P position
SFT PN -IPDM
Indicates [On/Off] condition of P or N position
SFT P -MET
Indicates [On/Off] condition of P position
SFT N -MET
Indicates [On/Off] condition of N position
ENGINE STATE
Indicates [Stop/Stall/Crank/Run] condition of engine states
S/L LOCK-IPDM
Indicates [On/Off] condition of steering lock unit (LOCK)
S/L UNLK-IPDM
Indicates [On/Off] condition of steering lock unit (UNLOCK)
DIAGNOSIS SYSTEM (BCM)
DLK-221
< SYSTEM DESCRIPTION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
*
1
: It is displayed but does not operate on CVT models.
*
2
: OFF is displayed when brake pedal is depressed while brake switch power supply is OFF.
ACTIVE TEST
S/L RELAY-REQ
Indicates [On/Off] condition of steering lock relay
VEH SPEED 1
Display the vehicle speed signal received from combination meter by numerical value [Km/h]
VEH SPEED 2
Display the vehicle speed signal received from ABS or VDC or TCM by numerical value [Km/h]
DOOR STAT-DR
Indicates [LOCK/READY/UNLK] condition of driver side door status
DOOR STAT-AS
Indicates [LOCK/READY/UNLK] condition of passenger side door status
ID OK FLAG
Indicates [Set/Reset] condition of key ID
PRMT ENG STRT
Indicates [Set/Reset] condition of engine start possibility
PRMT RKE STRT
NOTE:
This item is displayed, but cannot be monitored
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored
RKE-LOCK
Indicates [On/Off] condition of LOCK signal from Intelligent Key
RKE-UNLOCK
Indicates [On/Off] condition of UNLOCK signal from Intelligent Key
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
RKE-PANIC
NOTE:
This item is displayed, but cannot be monitored
RKE-MODE CHG
Indicates [On/Off] condition of MODE CHANGE signal from Intelligent Key
RKE OPE COUN1
When remote keyless entry receiver receives the signal transmitted while operating on Intelli-
gent Key, the numerical value start changing
RKE OPE COUN2
NOTE:
This item is displayed, but cannot be monitored
Monitor Item
Condition
Test item
Description
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation
• On: Operate
• Off: Non-operation
INSIDE BUZZER
This test is able to check warning chime in combination meter operation
• Take Out: Take away warning chime sounds when CONSULT-III screen is touched
• Key: Key warning chime sounds when CONSULT-III screen is touched
• Knob: OFF position warning chime sounds when CONSULT-III screen is touched
• Off: Non-operation
INDICATOR
This test is able to check warning lamp operation
• KEY ON: “KEY” Warning lamp illuminates when CONSULT-III screen is touched
• KEY IND: “KEY” Warning lamp blinks when CONSULT-III screen is touched
• Off: Non-operation
INT LAMP
This test is able to check interior room lamp operation
• On: Operate
• Off: Non-operation
DLK-222
< SYSTEM DESCRIPTION >
[TYPE 2]
DIAGNOSIS SYSTEM (BCM)
TRUNK
TRUNK : CONSULT-III Function (BCM - TRUNK) (Without Super Lock)
INFOID:0000000006548667
DATA MONITOR
LCD
This test is able to check meter display information
• BP N: Engine start operation indicator lamp indicate when CONSULT-III screen is touched
• BP I: Engine start operation indicator lamp indicate when CONSULT-III screen is touched
• ID NG: This item is displayed, but cannot be monitored
• ROTAT: This item is displayed, but cannot be monitored
• SFT P: Shift P warning lamp indicate when CONSULT-III screen is touched
• INSRT: This item is displayed, but cannot be monitored
• BATT: Key warning lamp indicator when CONSULT-III screen is touched
• NO KY: Key warning lamp indicator when CONSULT-III screen is touched
• OUTKEY: Engine start operation indicator lamp indicate when CONSULT-III screen is
touched
• LK WN: Engine start operation indicator lamp indicate when CONSULT-III screen is touched
FLASHER
This test is able to check security hazard lamp operation
The hazard lamps are activated after “LH/RH/Off” on CONSULT-III screen is touched
P RANGE
This test is able to check CVT shift selector power supply
• On: Operate
• Off: Non-operation
ENGINE SW ILLUMI
This test is able to check push-ignition switch illumination operation
Push-ignition switch illumination illuminates when “ON” on CONSULT-III screen is touched
PUSH SWITCH INDICATOR
This test is able to check LOCK indicator in push-ignition switch operation
LOCK indicator in push-ignition switch illuminates when “ON” on CONSULT-III screen is
touched
BATTERY SAVER
This test is able to check interior room lamp operation.
The interior room lamp will be activated after “ON” on CONSULT-III screen is touched.
TRUNK/BACK DOOR
This test is able to check back door opener actuator open operation.
This actuator opens when “Open” on CONSULT-III screen is touched.
RETRACTABLE MIRROR
This test is able to check auto retractable door mirror operation
• On: Operate
• Off: Non-operation
Test item
Description
Monitor Item
Contents
PUSH SW
Indicates [On/Off] condition of push switch
UNLK SEN -DR
Indicates [On/Off] condition of unlock sensor
VEH SPEED 1
Indicates [Km/h] condition of vehicle speed signal from combination meter
TR/BD OPEN SW
Indicates [ON/OFF] condition of back door opener switch.
TRNK/HAT MNTR
NOTE:
This item is displayed, but cannot be monitored
RKE-TR/BD
NOTE:
This item is displayed, but cannot be monitored
BCM
DLK-223
< ECU DIAGNOSIS INFORMATION >
[TYPE 2]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
ECU DIAGNOSIS INFORMATION
BCM
List of ECU Reference
INFOID:0000000006302961
ECU
Reference
BCM
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст