Juke F15 (2012 year). Service Repair Manual — part 314
FRONT SEAT (4WD)
SE-25
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
PASSENGER SEAT
CAUTION:
Always replace seat cushion as an assembly because occupant detection unit is equipped.
10. Seat cushion inner finisher
11.
Reclining device inner cover (front)
12. Reclining device inner cover (rear)
13. TORX bolt
14. Seat cushion trim
(without heater seat only)
15. Seat cushion pad
(without heater seat only)
16. Seat cushion silencer
17. Seat cushion assembly
(with heater seat only)
18. Lifter link
19. Lifter lever knob
20. Lifter lever knob cap
21. Reclining lever knob
22. Seat cushion outer finisher
23. Spring
24. Reclining device outer cover (front)
25. Reclining device outer cover (rear)
26. Outer lower cover
27. Side air bag module
28. Seatback silencer
29. Seat frame & adjuster assembly
: Pawl
: Metal clip
: Do not reuse
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
SE-26
< REMOVAL AND INSTALLATION >
FRONT SEAT (4WD)
LHD models
JMJIA4586GB
1.
Headrest
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Seatback silencer
5.
Side air bag module
6.
Spring
7.
Reclining device outer cover (rear)
8.
Reclining device outer cover (front)
9.
Seat cushion outer finisher
10. Reclining lever knob
11.
TORX bolt
12. Seat cushion silencer
13. Seat cushion assembly
14. Anchor bolt
15. Seat belt buckle
16. Seat cushion inner finisher
17. Reclining device inner cover (front)
18. Reclining device inner cover (rear)
19. Seatback pad
(without heater seat only)
20. Seatback trim
(without heater seat only)
21. Seatback assembly
(with heater seat only)
22. Seat frame & adjuster assembly
: Pawl
FRONT SEAT (4WD)
SE-27
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Removal and Installation
INFOID:0000000006412871
REMOVAL
CAUTION:
Before servicing, disconnect the battery cable from negative terminal or remove the fuse.
1.
Remove headrest.
2.
Set the seatback vertically.
3.
Slide seat to the frontmost position.
4.
Remove rear outer mounting TORX bolt.
5.
Remove rear inner mounting TORX bolt.
6.
Slide seat to the rearmost position.
7.
Remove front outer mounting TORX bolt.
8.
Remove front inner mounting TORX bolt.
9.
Remove seat cushion lower harness connectors and harness fixing clamps.
CAUTION:
Before performing removal operation, check the installation position of harness connectors and
harness fixing clamps.
10. Remove seat from the vehicle.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• When removing and installing, use shop cloths to protect parts from damage.
• When installing, tighten mounting TORX bolts according to
the numerical order (1, 2, 3, and 4 as shown in the figure),
starting from front inner mounting TORX bolt.
• Always fix the harness fixing clamp in position.
SEATBACK
SEATBACK : Disassembly and Assembly
INFOID:0000000006384860
DISASSEMBLY
CAUTION:
For models with heater seat, always replace heater seat as a seatback assembly without disassem-
bling trim and pad.
1.
Remove seatback retainer installed in the lower portion of seat cushion.
2.
Remove harness installed in the lower portion of seat cushion.
: Metal clip
: Do not reuse
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMJIA4591ZZ
SE-28
< REMOVAL AND INSTALLATION >
FRONT SEAT (4WD)
1.
Disconnect seatback heater unit harness connector
(A).(with heater seat only.)
2.
Remove seatback heater unit harness connector fixing clips
(A) and harness fixing clamp (B). (with heater seat only)
3.
Remove side air bag module harness connector fixing clips
(C) and harness fixing clamp (D).
3.
Open seatback fastener (A) and remove seatback retainer (B).
4.
Remove side air bag module harness fixing clamps from seat frame & adjuster assembly.
5.
Use pincers, etc., to press up pawls as shown by the arrows in
the figure, and remove headrest holder from seatback.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
6.
Remove side air bag module mounting nuts.
7.
Remove seatback trim and seatback pad from seat frame & adjuster assembly.
CAUTION:
Never subject side air bag module to impact by dropping or hitting.
8.
Remove side air bag module from seatback pad.
CAUTION:
For handling of side air bag module, refer to
SR-22, "Removal and Installation"
9.
Separate the seatback trim and seatback pad. (without heater seat only)
Remove hog rings, and separate the seatback trim and seatback pad.
CAUTION:
Before performing separating operation, check the installation position of hog rings.
10. Remove seatback silencer from seat frame & adjuster assembly.
ASSEMBLY
Note the following, and assemble in the reverse order of disassembly.
CAUTION:
Always install the hog ring in position.
SEAT CUSHION
: Vehicle front
JMJIA4602ZZ
JMJIA4363ZZ
PIIB4084J
FRONT SEAT (4WD)
SE-29
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
SEAT CUSHION : Disassembly and Assembly
INFOID:0000000006384861
DISASSEMBLY
CAUTION:
For models with heater seat and occupant detection unit, always replace heater seat and reminder as
a seat cushion assembly without disassembling trim and pad.
1.
Remove seat cushion outer finisher.
1.
Disengage pawls and remove lifter lever knob cap (1).
(Driver seat only)
2.
Remove fixing screws and remove lifter lever knob (2).
(Driver seat only)
3.
Disengage pawl using a screwdriver while pulling reclining
lever knob. Slide reclining lever knob toward seat front and
remove it.
4.
Pull seat cushion outer finisher toward seat front. Disengage pawls and metal clips. Slide seat cush-
ion outer finisher toward seat front. Remove seat cushion outer finisher.
2.
Remove harness installed in the lower portion of seat cushion.
Driver seat
: Pawl
JMJIA4592ZZ
: Pawl
JMJIA4593ZZ
1.
Seat cushion outer finisher
(Driver seat)
2.
Seat cushion outer finisher
(Passenger seat)
: Pawl
: Metal clip
JMJIA4594ZZ
SE-30
< REMOVAL AND INSTALLATION >
FRONT SEAT (4WD)
1.
Disconnect seat cushion heater unit harness connector (A).
(with heater seat only)
2.
Remove seat cushion heater unit harness connector fixing
clip (B) and harness fixing clamps (C). (with heater seat
only)
3.
Remove seat belt buckle harness connector fixing clip (D)
and harness fixing clamps (E).
Passenger seat
1.
Disconnect seat cushion heater unit harness connector (A).
(with heater seat only)
2.
Remove seat cushion heater unit harness connector fixing
clip (B) and harness fixing clamps (C). (with heater seat
only)
3.
Disconnect occupant detection unit harness connector (D).
4.
Remove seat belt buckle harness connector fixing clip (E)
and harness fixing clamps (F).
3.
Remove seat cushion inner finisher.
1.
Remove harness fixing clamp of seat belt buckle installed on seat frame & adjuster assembly.
2.
Remove seat belt buckle mounting anchor bolt, and then remove seat belt buckle from seat frame
&adjuster assembly.
3.
Pull seat cushion inner finisher forward. Disengage pawls
and metal clips.
4.
Remove seat cushion retainer from seat frame & adjuster assembly. Remove seat cushion trim and seat
cushion pad.
5.
Remove hog rings, and separate the seat cushion trim and seat cushion pad. (without driver heater seat
only)
CAUTION:
Before performing separating operation, check the installation position of hog rings.
6.
Remove seat cushion silencer from seat frame & adjuster assembly.
7.
Remove seatback trim and seatback pad from seat frame & adjuster assembly.
Refer to
SE-27, "SEATBACK : Disassembly and Assembly"
.
8.
Remove reclining device cover.
• Remove fixing screw, and then remove reclining device outer cover (front and rear).
• Remove fixing screw, and then remove reclining device inner cover (front and rear).
9.
Remove following parts from seat frame & adjuster assembly.
• Remove reclining spring.
• Remove fixing screws. Pull outer lower cover toward seat outer. Disengage metal clips. Remove outer
lower cover. (driver seat only)
• Remove fixing screws, and then remove inner lower cover. (driver seat only)
: Vehicle front
JMJIA4603ZZ
: Vehicle front
JMJIA4604ZZ
: Pawl
: Metal clip
JMJIA4595ZZ
FRONT SEAT (4WD)
SE-31
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
ASSEMBLY
Note the following, and assemble in the reverse order of disassembly.
CAUTION:
• Always install the hog rings in position.
• When installing seat cushion finisher, always slide seat cush-
ion outer finisher toward seat rear, engage portion (A) of seat
frame & adjuster assembly and portion (B) of seat cushion
outer finisher, and then install pawls and metal clips of seat
cushion outer finisher.
: Vehicle front
JMJIA4612ZZ
SE-32
< REMOVAL AND INSTALLATION >
REAR SEAT (2WD)
REAR SEAT (2WD)
Exploded View
INFOID:0000000006404991
1.
Headrest
2.
Headrest holder (locked)
3.
Headrest holder (free)
4.
Seatback trim RH
5.
Seatback pad RH
6.
Seat lock cover RH
7.
Seatback lock knob
8.
Seatback lock knob finisher
9.
Seatback lock assembly RH
10. Striker RH
11.
Lock washer
12. Side hinge
13. Bush
14. Seat cushion hook
15. Seat cushion pad
16. Seat cushion trim
17. Side hinge LH
18. Seatback lock assembly LH
19. Seat lock cover LH
20. Seatback pad LH
21. Seatback trim LH
JMJIA4587GB
REAR SEAT (2WD)
SE-33
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
SEAT CUSHION
SEAT CUSHION : Removal and Installation
INFOID:0000000006365640
REMOVAL
1.
Lift up front end portion of seat cushion and disengage seat
cushion hook.
2.
Pull out seat belt buckle from seat cushion.
3.
Remove seat cushion from the vehicle.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
SEAT CUSHION : Disassembly and Assembly
INFOID:0000000006365641
DISASSEMBLY
Remove hog rings, and separate the seat cushion trim and seat cushion pad.
CAUTION:
Before performing separating operation, check the installation position of hog rings.
ASSEMBLY
Note the following item, and assemble in the reverse order of disassembly.
CAUTION:
Always install the hog ring in position.
SEATBACK
SEATBACK : Removal and Installation
INFOID:0000000006365642
LH SIDE SEATBACK
Removal
CAUTION:
Remove seatback with seat cushion installed.
1.
Temporarily move seat cushion to the position where center anchor of center seat belts can be removed.
2.
Remove center anchor mounting bolt of center seat belt. Remove center anchor.
22. Center headrest
23. Seatback silencer LH
24. Seatback silencer RH
25. Center seat belt finisher
26. Center hinge
27. Seat belt buckle
28. Seatback tether cover
29. Center seat belt bracket
30. Center seat belt
31. Seatback frame RH
32. Seatback frame LH
: Pawl
: Metal clip
: N·m (kg-m, ft-lb)
PIIB8352J
SE-34
< REMOVAL AND INSTALLATION >
REAR SEAT (2WD)
3.
Return seat cushion to the normal position.
4.
Unlock seatback lock assembly. Tilt seatback toward vehicle front. Remove headrests.
5.
Fold seatback toward vehicle front.
6.
Pull up seatback carpet (A). Remove mounting bolts (B) of seat-
back hinge portion.
7.
Remove seatback from the vehicle.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
Installation
Note the following items, and install in the reverse order of removal.
CAUTION:
• When removing and installing, use shop cloths to protect parts from damage.
• Install seat cushion to the vehicle, and then install seatback.
• When installing seatback, tighten mounting bolts according to
the numerical order (1, 2, 3, and 4 as shown in the figure).
RH SIDE SEATBACK
Removal
CAUTION:
Remove seatback with seat cushion installed.
1.
Unlock seatback lock assembly. Tilt seatback toward vehicle front. Remove headrest.
2.
Fold seatback toward vehicle front.
3.
Pull up seatback carpet (A). Remove mounting bolts (B) of seat-
back hinge portion.
4.
Remove seatback from the vehicle.
CAUTION:
When removing and installing, use shop cloths to protect parts from damage.
JMJIA4458ZZ
JMJIA4460ZZ
JMJIA4459ZZ
REAR SEAT (2WD)
SE-35
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
Installation
Note the following items, and install in the reverse order of removal.
CAUTION:
• When removing and installing, use shop cloths to protect parts from damage.
• Install seat cushion to the vehicle, and then install seatback.
• When installing seatback, tighten mounting bolts according to
the numerical order (1, 2, 3, and 4 as shown in the figure).
SEATBACK : Disassembly and Assembly
INFOID:0000000006365643
DISASSEMBLY
LH side seatback
1.
Remove headrest holder.
1.
Pull seat lock cover in direction indicated by the arrow as
shown in the figure. Remove seat lock cover.
2.
Pull tether cover in direction indicated by the arrow as
shown in the figure. Remove tether cover.
3.
Open seatback fastener (A) and remove seatback retainer
(B).
JMJIA4461ZZ
: Metal clip
JMJIA4372ZZ
: Pawl
JMJIA4611ZZ
JMJIA4371ZZ
SE-36
< REMOVAL AND INSTALLATION >
REAR SEAT (2WD)
4.
Use pincers, etc., to press up pawls as shown by the arrows
in the figure, and remove headrest holder from seatback.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
2.
Remove seatback lock knob finisher.
1.
Rotate seatback lock knob counterclockwise. Remove seat-
back lock knob.
2.
Push up seatback lock knob finisher while pressing pawls
indicated by arrows as shown in the figure. Remove seat-
back lock finisher from seatback.
CAUTION:
When installing seatback lock knob finisher, check
front and rear orientation and be careful to install it nor-
mally.
3.
Remove center seat belt finisher from seatback.
Lift up front of center seat belt finisher. Disengage front pawls.
Pull center seat belt finisher toward seat front. Disengage rear
pawls.
4.
Remove seatback trim and seatback pad from seatback frame
5.
Remove hog rings, and separate the seatback trim and seatback pad.
CAUTION:
Before performing separating operation, check the installation position of hog rings.
6.
Remove seatback silencer from seatback frame.
7.
Remove seatback lock assembly mounting bolts, and then remove seatback lock assembly from seatback
frame.
PIIB4084J
JMJIA4374ZZ
JMJIA4375ZZ
: Pawl
JMJIA4373ZZ
REAR SEAT (2WD)
SE-37
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
8.
Remove center seat belt retractor from seatback frame.
Refer to
SB-12, "SEAT BELT RETRACTOR : Removal and Installation"
RH side seatback
1.
Remove headrest holder.
1.
Pull seat lock cover in direction indicated by the arrow as
shown in the figure. Remove seat lock cover.
2.
Pull tether cover in direction indicated by the arrow as
shown in the figure. Remove tether cover.
3.
Open seatback fastener (A) and remove seatback retainer
(B).
4.
Use pincers, etc., to press up pawls as shown by the arrows
in the figure, and remove headrest holder from seatback.
CAUTION:
Before installing headrest holder check its orientation.
(front/rear and right/left)
2.
Remove seatback lock knob finisher.
: Metal clip
JMJIA4370ZZ
: Pawl
JMJIA4611ZZ
JMJIA4369ZZ
PIIB4084J
SE-38
< REMOVAL AND INSTALLATION >
REAR SEAT (2WD)
1.
Rotate seatback lock knob counterclockwise. Remove seat-
back lock knob.
2.
Push up seatback lock knob finisher while pressing pawls
indicated by arrows as shown in the figure. Remove seat-
back lock finisher from seatback.
CAUTION:
When installing seatback lock knob finisher, check
front and rear orientation and be careful to install it nor-
mally.
3.
Remove seatback trim and seatback pad from seatback frame.
4.
Remove hog rings, and separate the seatback trim and seatback pad.
CAUTION:
Before performing separating operation, check the installation position of hog rings.
5.
Remove seatback silencer from seatback frame.
6.
Remove seatback lock assembly mounting bolts, and then remove seatback lock assembly from seatback
frame.
INSTALLATION
Note the following, and assemble in the reverse order of disassembly.
CAUTION:
Always install the hog ring in position.
SEATBACK HINGE
SEATBACK HINGE : Removal and Installation
INFOID:0000000006365644
CENTER HINGE
Removal
1.
Remove seatback LH and RH from the vehicle.
Refer to
SE-33, "SEATBACK : Removal and Installation"
.
2.
Remove seat cushion from the vehicle.
Refer to
SE-33, "SEAT CUSHION : Removal and Installation"
.
3.
Remove center hinge mounting bolts, and then remove center hinge from the vehicle.
Installation
Note the following items, and install in the reverse order of removal.
CAUTION:
When installing center hinge, tighten mounting bolts to the specified torque according to the numeri-
cal order as shown in the figure.
JMJIA4374ZZ
JMJIA4375ZZ
REAR SEAT (2WD)
SE-39
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
K
L
M
A
B
SE
N
O
P
1.
Temporarily tighten mounting bolt (1).
2.
Tighten mounting bolts in numerical order (2 and 3 as
shown in the figure) to the specified torque.
For the specified torque, refer to
SIDE HINGE
Removal
1.
Remove seatback from the vehicle.
Refer to
SE-33, "SEATBACK : Removal and Installation"
.
2.
Remove side hinge mounting bolt, and then remove side hinge from luggage side lower finisher.
Installation
Installation is the reverse order of removal. Tighten bolts to the specified torque.
For the specified torque, refer to
.
SEATBACK STRIKER
SEATBACK STRIKER : Removal and Installation
INFOID:0000000006365645
REMOVAL
1.
Remove seatback LH and RH from the vehicle.
Refer to
SE-33, "SEATBACK : Removal and Installation"
.
2.
Remove seat cushion from the vehicle.
Refer to
SE-33, "SEAT CUSHION : Removal and Installation"
.
3.
Remove side hinge from the vehicle.
Refer to
SE-38, "SEATBACK HINGE : Removal and Installation"
.
4.
Remove outer anchor mounting anchor bolt, and then remove outer anchor.
5.
Remove luggage side lower finisher from the vehicle.
Refer to
INT-31, "LUGGAGE SIDE LOWER FINISHER : Removal and Installation"
.
6.
Remove mounting bolts or nuts of striker, and then remove striker from the vehicle.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
When installing striker, tighten mounting bolts or nuts to the specified torque according to the numer-
ical order as shown in the figure.
: Vehicle front
JMJIA4456GB
SE-40
< REMOVAL AND INSTALLATION >
REAR SEAT (2WD)
1.
Temporarily tighten mounting bolts in numerical order (1
and 2 as shown in the figure).
2.
Tighten mounting bolts or nuts to the specified torque in
numerical order (3, 4, and 5 as shown in the figure).
For the specified torque, refer to
: Vehicle front
JMJIA4455GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст