Juke F15 (2012 year). Service Repair Manual — part 69
DLK-96
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
REMOTE KEYLESS ENTRY RECEIVER
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-93, "Removal and Installation"
NO
>> Repair or replace harness.
4.
CHECK REMOTE KEYLESS ENTRY RECEIVER OUTPUT SIGNAL
1.
Reconnect remote keyless entry receiver connector.
2.
Check signal between remote keyless entry receiver harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace remote keyless entry receiver.
5.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 2
1.
Disconnect BCM connector and remote keyless entry receiver connector.
2.
Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK REMOTE KEYLESS ENTRY RECEIVER RSSI OUTPUT SIGNAL
1.
Reconnect BCM and remote keyless entry receiver connector.
2.
Check signal between remote keyless entry receiver harness connector and ground using oscilloscope.
BCM
Ground
Continuity
Connector
Terminal
M68
19
Not existed
(+)
(–)
Condition
Signal
(Reference value)
Remote keyless entry receiver
Connector
Terminal
M75
2
Ground
Waiting
Press the Intelligent
Key lock or unlock
button
JMKIA3838GB
JMKIA3841GB
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M68
20
M75
2
Existed
BCM
Ground
Continuity
Connector
Terminal
M68
20
Not existed
REMOTE KEYLESS ENTRY RECEIVER
DLK-97
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Replace remote keyless entry receiver.
7.
CHECK REMOTE KEYLESS ENTRY RECEIVER RSSI CIRCUIT
1.
Disconnect BCM and remote keyless entry receiver connector.
2.
Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-93, "Removal and Installation"
NO
>> Repair or replace harness.
(+)
(–)
Condition
Signal
(Reference value)
Remote keyless entry receiver
Connector
Terminal
M75
3
Ground
Waiting
Press and hold Intel-
ligent Key lock or un-
lock button
JMKIA5952GB
JMKIA5953GB
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M68
22
M75
3
Existed
BCM
Ground
Continuity
Connector
Terminal
M68
22
Not existed
DLK-98
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
SHIFT P WARNING LAMP
SHIFT P WARNING LAMP
Component Function Check
INFOID:0000000006601095
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “LCD” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Shift P warning lamp is OK.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000006601096
1.
CHECK SHIFT P WARNING LAMP
MWI-22, "On Board Diagnosis Function"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
>> INSPECTION END
Monitor item
Status
LCD
SFT P
Shift P warning lamp
Turns ON
SUPER LOCK ACTUATOR
DLK-99
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
SUPER LOCK ACTUATOR
DRIVER SIDE
DRIVER SIDE : Component Function Check
INFOID:0000000006302777
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “SUPER LOCK” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Super lock actuator is OK.
NO
>> Refer to
DLK-99, "DRIVER SIDE : Diagnosis Procedure"
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000006302778
1.
CHECK SUPER LOCK ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check voltage between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front door lock assembly (driver side).
NO
>> GO TO 2.
2.
CHECK SUPER LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM connector and all door lock assembly connector.
2.
Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
Monitor item
Status
SUPER LOCK
LOCK
Super lock actuators
LOCK
UNLOCK
UNLOCK
(+)
(–)
Condition
Voltage
(Approx.)
Front door lock assembly
(driver side)
Connector
Terminal
D13
1
Ground
Lock
12 V
2
Unlock
BCM
Front door lock assembly
(driver side)
Continuity
Connector
Terminal
Connector
Terminal
M69
59
D13
1
Existed
66
2
BCM
Ground
Continuity
Connector
Terminal
M69
59
Not existed
66
DLK-100
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
SUPER LOCK ACTUATOR
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each super lock actuator.
NO
>> Replace BCM. Refer to
BCS-93, "Removal and Installation"
PASSENGER SIDE
PASSENGER SIDE : Component Function Check
INFOID:0000000006302779
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “SUPER LOCK” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Super lock actuator is OK.
NO
>> Refer to
DLK-100, "PASSENGER SIDE : Diagnosis Procedure"
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000006302780
1.
CHECK SUPER LOCK ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (passenger side) connector.
3.
Check voltage between front door lock assembly (passenger side) harness connector and ground.
Is the inspection result normal?
YES
>> Replace front door lock assembly (passenger side).
NO
>> GO TO 2.
2.
CHECK SUPER LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM connector and all door lock assembly connector.
2.
Check continuity between BCM harness connector and front door lock assembly (passenger side) har-
ness connector.
(+)
(–)
Condition
Voltage
(Approx.)
BCM
Connector
Terminal
M69
59
Ground
Lock
12 V
66
Unlock
Monitor item
Status
SUPER LOCK
LOCK
Super lock actuators
LOCK
UNLOCK
UNLOCK
(+)
(–)
Condition
Voltage
(Approx.)
Front door lock assembly
(passenger side)
Connector
Terminal
D30
1
Ground
Lock
12 V
2
Unlock
SUPER LOCK ACTUATOR
DLK-101
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each super lock actuator.
NO
>> Replace BCM. Refer to
BCS-93, "Removal and Installation"
REAR LH
REAR LH : Component Function Check
INFOID:0000000006302781
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “SUPER LOCK” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Super lock actuator is OK.
NO
>> Refer to
DLK-101, "REAR LH : Diagnosis Procedure"
.
REAR LH : Diagnosis Procedure
INFOID:0000000006600490
1.
CHECK SUPER LOCK ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear door lock assembly LH connector.
3.
Check voltage between rear door lock assembly LH harness connector and ground.
BCM
Front door lock assembly
(passenger side)
Continuity
Connector
Terminal
Connector
Terminal
M69
59
D30
1
Existed
B10
55
2
BCM
Ground
Continuity
Connector
Terminal
M69
59
Not existed
B10
55
(+)
(–)
Condition
Voltage
(Approx.)
BCM
Connector
Terminal
M69
59
Ground
Lock
12 V
B10
55
Unlock
Monitor item
Status
SUPER LOCK
LOCK
Super lock actuators
LOCK
UNLOCK
UNLOCK
DLK-102
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
SUPER LOCK ACTUATOR
Is the inspection result normal?
YES
>> Replace rear door lock assembly LH.
NO
>> GO TO 2.
2.
CHECK SUPER LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM connector and all door lock assembly connector.
2.
Check continuity between BCM harness connector and rear door lock assembly LH harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each super lock actuator.
NO
>> Replace BCM. Refer to
BCS-93, "Removal and Installation"
REAR RH
REAR RH : Component Function Check
INFOID:0000000006302783
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “SUPER LOCK” in “ACTIVE TEST” mode.
3.
Check that the function operates normally according to the following conditions.
(+)
(–)
Condition
Voltage
(Approx.)
Rear door lock assembly LH
Connector
Terminal
D66
1
Ground
Lock
12 V
2
Unlock
BCM
Rear door lock assembly LH
Continuity
Connector
Terminal
Connector
Terminal
M69
59
D66
1
Existed
B10
55
2
BCM
Ground
Continuity
Connector
Terminal
M69
59
Not existed
B10
55
(+)
(–)
Condition
Voltage
(Approx.)
BCM
Connector
Terminal
M69
59
Ground
Lock
12 V
B10
55
Unlock
Monitor item
Status
SUPER LOCK
LOCK
Super lock actuators
LOCK
UNLOCK
UNLOCK
SUPER LOCK ACTUATOR
DLK-103
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> Back door lock actuator is OK.
NO
>> Refer to
DLK-103, "REAR RH : Diagnosis Procedure"
REAR RH : Diagnosis Procedure
INFOID:0000000006600493
1.
CHECK SUPER LOCK ACTUATOR INPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect rear door lock assembly RH connector.
3.
Check voltage between rear door lock assembly RH harness connector and ground.
Is the inspection result normal?
YES
>> Replace rear door lock assembly RH.
NO
>> GO TO 2.
2.
CHECK SUPER LOCK ACTUATOR CIRCUIT
1.
Disconnect BCM connector and all door lock assembly connector.
2.
Check continuity between BCM harness connector and rear door lock assembly RH harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK BCM OUTPUT SIGNAL
1.
Connect BCM connector.
2.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Check for internal short of each super lock actuator.
NO
>> Replace BCM. Refer to
BCS-93, "Removal and Installation"
(+)
(–)
Condition
Voltage
(Approx.)
Rear door lock assembly RH
Connector
Terminal
D46
1
Ground
Lock
12 V
2
Unlock
BCM
Rear door lock assembly RH
Continuity
Connector
Terminal
Connector
Terminal
M69
59
D46
1
Existed
B10
55
2
BCM
Ground
Continuity
Connector
Terminal
M69
59
Not existed
B10
55
(+)
(–)
Condition
Voltage
(Approx.)
BCM
Connector
Terminal
M69
59
Ground
Lock
12 V
B10
55
Unlock
DLK-104
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
UNLOCK SENSOR
UNLOCK SENSOR
Component Function Check
INFOID:0000000006600435
1.
CHECK FUNCTION
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “UNLK SEN -DR” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Unlock sensor is OK.
NO
>> Refer to
DLK-104, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000006600436
1.
CHECK BCM OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check signal between front door lock assembly (driver side) harness connector and ground using oscillo-
scope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK UNLOCK SENSOR CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-93, "Removal and Installation"
Monitor item
Condition
Status
UNLK SEN -DR
Driver side door
Lock
OFF
Unlock
ON
(+)
(–)
Signal
(Reference value)
Front door lock assembly (driver side)
Connector
Terminal
D13
4
Ground
PKIB4960J
BCM
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M68
31
D13
4
Existed
BCM
Ground
Continuity
Connector
Terminal
M68
31
Not existed
UNLOCK SENSOR
DLK-105
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
NO
>> Repair or replace harness.
3.
CHECK UNLOCK SENSOR GROUND CIRCUIT
Check continuity between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK UNLOCK SENSOR
DLK-105, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace front door lock assembly (driver side).
5.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000006600437
1.
CHECK UNLOCK SENSOR
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check continuity between front door lock assembly (driver side) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front lock assembly (driver side).
Front door lock assembly (driver side)
Ground
Continuity
Connector
Terminal
D13
5
Existed
Front door lock assembly (driver side)
Condition
Continuity
Terminal
4
5
Driver side door
Unlock
Existed
Lock
Not existed
DLK-106
< SYMPTOM DIAGNOSIS >
[TYPE 1]
DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH
SYMPTOM DIAGNOSIS
DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH
ALL DOOR REQUEST SWITCHES
ALL DOOR REQUEST SWITCHES : Description
INFOID:0000000006601276
All doors do not lock/unlock using all door request switches.
ALL DOOR REQUEST SWITCHES : Diagnosis Procedure
INFOID:0000000006601277
1.
CHECK REMOTE KEYLESS ENTRY FUNCTION
Check remote keyless entry function.
Does door lock/unlock with Intelligent Key button?
YES
>> GO TO 2.
NO
>> Refer to
.
2.
CHECK “LOCK/UNLOCK BY I-KEY” SETTING IN “WORK SUPPORT”
1.
Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.
2.
Select “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT” mode.
3.
Check “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT”.
Refer to
DLK-43, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY) (With Super
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “LOCK/UNLOCK BY I-KEY” in “WORK SUPPORT”.
3.
CHECK INSIDE KEY ANTENNA
Check inside key antenna.
• Instrument center: Refer to
.
• Console: Refer to
• Luggage room: Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK OUTSIDE KEY ANTENNA
Check outside key antenna.
• Driver side: Refer to
.
• Passenger side: Refer to
.
• Rear bumper: Refer to
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-93, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
DRIVER SIDE DOOR REQUEST SWITCH
DRIVER SIDE DOOR REQUEST SWITCH : Description
INFOID:0000000006601278
All doors do not lock/unlock using driver side door request switch.
DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH
DLK-107
< SYMPTOM DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DRIVER SIDE DOOR REQUEST SWITCH : Diagnosis Procedure
INFOID:0000000006601279
1.
CHECK DRIVER SIDE DOOR REQUEST SWITCH
Check driver side door request switch.
Refer to
DLK-85, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK OUTSIDE KEY ANTENNA
Check outside key antenna (driver side).
Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-93, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
PASSENGER SIDE DOOR REQUEST SWITCH
PASSENGER SIDE DOOR REQUEST SWITCH : Description
INFOID:0000000006601280
All doors do not lock/unlock using passenger side door request switch.
PASSENGER SIDE DOOR REQUEST SWITCH : Diagnosis Procedure
INFOID:0000000006601281
1.
CHECK PASSENGER SIDE DOOR REQUEST SWITCH
Check passenger side door request switch.
Refer to
DLK-85, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK OUTSIDE KEY ANTENNA
Check outside key antenna (passenger side).
Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-93, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
BACK DOOR REQUEST SWITCH
BACK DOOR REQUEST SWITCH : Description
INFOID:0000000006601282
All doors do not lock/unlock using back door request switch.
DLK-108
< SYMPTOM DIAGNOSIS >
[TYPE 1]
DOOR DOES NOT LOCK/UNLOCK WITH DOOR REQUEST SWITCH
BACK DOOR REQUEST SWITCH : Diagnosis Procedure
INFOID:0000000006601283
1.
CHECK BACK DOOR REQUEST SWITCH
Check back door request switch.
Refer to
DLK-71, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK OUTSIDE KEY ANTENNA
Check outside key antenna (rear bumper).
Refer to
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-93, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
DOOR DOES NOT LOCK/UNLOCK WITH DOOR KEY CYLINDER OPERATION
DLK-109
< SYMPTOM DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR DOES NOT LOCK/UNLOCK WITH DOOR KEY CYLINDER OPERA-
TION
Diagnosis Procedure
INFOID:0000000006614835
1.
CHECK POWER DOOR LOCK OPERATION
Check power door lock operation.
Does door lock/unlock with door lock and unlock switch?
YES
>> GO TO 2.
NO
>> Go to
DLK-110, "ALL DOOR : Diagnosis Procedure"
2.
CHECK UNLOCK SENSOR
Check unlock sensor.
Refer to
DLK-104, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-93, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
DLK-110
< SYMPTOM DIAGNOSIS >
[TYPE 1]
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK
SWITCH
ALL DOOR
ALL DOOR : Description
INFOID:0000000006601263
All doors do not lock/unlock using door lock and unlock switch.
ALL DOOR : Diagnosis Procedure
INFOID:0000000006601264
1.
CHECK DOOR LOCK AND UNLOCK SWITCH
Check door lock and unlock switch.
Refer to
DLK-79, "DRIVER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK DOOR LOCK ACTUATOR
Check front door lock assembly (driver side).
Refer to
DLK-74, "DRIVER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-87, "Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-93, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000006601265
Driver side door does not lock/unlock using door lock and unlock switch.
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000006601266
1.
CHECK DOOR LOCK ACTUATOR
Check front door lock assembly (driver side).
Refer to
DLK-74, "DRIVER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-93, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
DLK-111
< SYMPTOM DIAGNOSIS >
[TYPE 1]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
PASSENGER SIDE
PASSENGER SIDE : Description
INFOID:0000000006601267
Passenger side door does not lock/unlock using door lock and unlock switch.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000006601268
1.
CHECK DOOR LOCK ACTUATOR
Check front door lock assembly (passenger side).
Refer to
DLK-75, "PASSENGER SIDE : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-93, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
REAR LH
REAR LH : Description
INFOID:0000000006601269
Rear LH side door does not lock/unlock using door lock and unlock switch.
REAR LH : Diagnosis Procedure
INFOID:0000000006601270
1.
CHECK DOOR LOCK ACTUATOR
Check rear door lock assembly LH.
Refer to
DLK-76, "REAR LH : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-93, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
REAR RH
REAR RH : Description
INFOID:0000000006601271
Rear RH side door does not lock/unlock using door lock and unlock switch.
REAR RH : Diagnosis Procedure
INFOID:0000000006601272
1.
CHECK DOOR LOCK ACTUATOR
Check rear door lock assembly RH.
Refer to
DLK-77, "REAR RH : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст