Juke F15 (2012 year). Service Repair Manual — part 68

DLK-80

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

DOOR LOCK AND UNLOCK SWITCH

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-93, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK DOOR LOCK AND UNLOCK SWITCH GROUND

Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK DOOR LOCK AND UNLOCK SWITCH

Refer to

DLK-80, "DRIVER SIDE : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace power window main switch. Refer to

PWC-44, "Removal and Installation"

.

5.

CHECK INTERMITTENT INCIDENT

Refer to

GI-42, "Intermittent Incident"

.

>> INSPECTION END

DRIVER SIDE : Component Inspection

INFOID:0000000006302758

1.

CHECK DOOR LOCK AND UNLOCK SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect power window main switch connector.

3.

Check continuity between power window main switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace power window main switch.

PASSENGER SIDE

PASSENGER SIDE : Component Function Check

INFOID:0000000006302759

1.

CHECK FUNCTION

1.

Select “DOOR LOCK” of “BCM” using CONSULT-III.

2.

Select “CDL LOCK SW”, “CDL UNLOCK SW” in “DATA MONITOR” mode.

BCM

Ground

Continuity

Connector

Terminal

M68

12

Not existed

13

Power window main switch

Ground

Continuity

Connector

Terminal

D5

1

Existed

Power window main switch

Condition

Continuity

Terminal

3

1

Door lock and unlock
switch

LOCK

Existed

UNLOCK

Not existed

15

LOCK

Not existed

UNLOCK

Existed

DOOR LOCK AND UNLOCK SWITCH

DLK-81

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

3.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Door lock and unlock switch is OK.

NO

>> Refer to

DLK-81, "PASSENGER SIDE : Diagnosis Procedure"

.

PASSENGER SIDE : Diagnosis Procedure

INFOID:0000000006599581

1.

CHECK DOOR LOCK AND UNLOCK SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect front power window switch (passenger side) connector.

3.

Check signal between front power window switch (passenger side) harness connector and ground using
oscilloscope.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK DOOR LOCK AND UNLOCK SWITCH CIRCUIT

1.

Disconnect BCM connector and power window main switch connector.

2.

Check continuity between BCM harness connector and front power window switch (passenger side) har-
ness connector.

3.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-93, "Removal and Installation"

.

NO

>> Repair or replace harness.

Monitor item

Condition

Status

CDL LOCK SW

Door lock and unlock switch

Lock

ON

Unlock

OFF

CDL UNLOCK SW

Lock

OFF

Unlock

ON

(+)

(–)

Signal

(Reference value)

Front power window switch (passenger side)

Connector

Terminal

D26

1

Ground

1.0 - 1.5 V

2

JPMIA0012GB

BCM

Front power window switch (passenger side)

Continuity

Connector

Terminal

Connector

Terminal

M68

12

D26

1

Existed

13

2

BCM

Ground

Continuity

Connector

Terminal

M68

12

Not existed

13

DLK-82

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

DOOR LOCK AND UNLOCK SWITCH

3.

CHECK DOOR LOCK AND UNLOCK SWITCH GROUND

Check continuity between front power window switch (passenger side) harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK DOOR LOCK AND UNLOCK SWITCH

Refer to

DLK-82, "PASSENGER SIDE : Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace front power window switch (passenger side). Refer to

PWC-44, "Removal and Installa-

tion"

.

5.

CHECK INTERMITTENT INCIDENT

Refer to

GI-42, "Intermittent Incident"

.

>> INSPECTION END

PASSENGER SIDE : Component Inspection

INFOID:0000000006599582

1.

CHECK DOOR LOCK AND UNLOCK SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect front power window switch (passenger side) connector.

3.

Check continuity between front power window switch (passenger side) terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace front power window switch (passenger side).

Front power window switch (passenger side)

Ground

Continuity

Connector

Terminal

D26

3

Existed

Front power window switch (passenger side)

Condition

Continuity

Terminal

1

3

Door lock and unlock
switch

LOCK

Existed

UNLOCK

Not existed

2

LOCK

Not existed

UNLOCK

Existed

DOOR LOCK STATUS INDICATOR

DLK-83

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

DOOR LOCK STATUS INDICATOR

Component Function Check

INFOID:0000000006302762

1.

CHECK FUNCTION

1.

Select “DOOR LOCK” of “BCM” using CONSULT-III.

2.

Select “DOOR LOCK IND” in “ACTIVE TEST” mode.

3.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Door lock status indicator is OK.

NO

>> Refer to

DLK-83, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006302763

1.

CHECK DOOR LOCK STATUS INDICATOR INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect door lock status indicator connector.

3.

Check voltage between door lock status indicator harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK DOOR LOCK STATUS INDICATOR CIRCUIT

1.

Disconnect BCM connector.

2.

Check continuity between BCM harness connector and door lock status indicator harness connector.

3.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-93, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK DOOR LOCK STATUS INDICATOR GROUND

Check continuity between door lock status indicator harness connector and ground.

Monitor item

Status

DOOR LOCK IND

ON

Door lock status indicator

Turns ON

OFF

Turns OFF

(+)

(–)

Condition

Voltage

(Approx.)

Door lock status indicator

Connector

Terminal

M83

1

Ground

Door lock operation is accom-
plished

12 V

Any door is OPEN

0 V

BCM

Door lock status indicator

Continuity

Connector

Terminal

Connector

Terminal

M68

16

M83

1

Existed

BCM

Ground

Continuity

Connector

Terminal

M68

16

Not existed

DLK-84

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

DOOR LOCK STATUS INDICATOR

Is the inspection result normal?

YES

>> Replace door lock status indicator.

NO

>> Repair or replace harness.

Door lock status indicator

Ground

Continuity

Connector

Terminal

M83

2

Existed

DOOR REQUEST SWITCH

DLK-85

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

DOOR REQUEST SWITCH

Component Function Check

INFOID:0000000006302787

1.

CHECK FUNCTION

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.

2.

Select “REQ SW-DR”, “REQ SW-AS” in “DATA MONITOR” mode.

3.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Front door request switch is OK.

NO

>> Refer to

DLK-85, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006302788

1.

CHECK DOOR REQUEST SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect malfunctioning front door request switch connector.

3.

Check voltage between malfunctioning front door request switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> GO TO 2.

2.

CHECK DOOR REQUEST SWITCH CIRCUIT

1.

Disconnect BCM connector.

2.

Check continuity between malfunctioning front door request switch harness connector and BCM harness
connector.

3.

Check continuity between malfunctioning front door request switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-93, "Removal and Installation"

.

NO

>> Repair or replace harness.

Monitor item

Condition

Status

REQ SW -DR

Driver side door request switch

Pressed

ON

Released

OFF

REQ SW -AS

Passenger side door request switch

Pressed

ON

Released

OFF

(+)

(–)

Voltage

(Approx.)

Front door request switch

Connector

Terminal

Driver side

D11

1

Ground

12 V

Passenger side

D31

2

Front door request switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

Driver side

D11

1

M70

75

Existed

Passenger side

D31

2

76

Front door request switch

Ground

Continuity

Connector

Terminal

Driver side

D11

1

Not existed

Passenger side

D31

2

DLK-86

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

DOOR REQUEST SWITCH

3.

CHECK DOOR REQUEST SWITCH GROUND CIRCUIT

Check continuity between malfunctioning front door request switch harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK DOOR REQUEST SWITCH

Refer to

DLK-86, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace malfunctioning front door request switch.

5.

CHECK INTERMITTENT INCIDENT

Refer to

GI-42, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000006302789

1.

CHECK DOOR REQUEST SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect malfunctioning front door request switch connector.

3.

Check continuity between malfunctioning front door request switch terminals.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace malfunctioning front door request switch.

Front door request switch

Ground

Continuity

Connector

Terminal

Driver side

D11

2

Existed

Passenger side

D31

1

Front door request switch

Condition

Continuity

Terminal

1

2

Door request switch

Pressed

Existed

Released

Not existed

DOOR SWITCH

DLK-87

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

DOOR SWITCH

Component Function Check

INFOID:0000000006302753

1.

CHECK FUNCTION

1.

Select “DOOR LOCK” of “BCM” using CONSULT-III.

2.

Select “DOOR SW-DR”, “DOOR SW-AS”, “DOOR SW-RL”, “DOOR SW-RR”, “DOOR SW-BK” in “DATA
MONITOR” mode.

3.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Door switch is OK.

NO

>> Refer to

DLK-87, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006302754

1.

CHECK DOOR SWITCH INPUT SIGNAL

1.

Turn ignition switch OFF.

2.

Disconnect malfunctioning door switch connector.

3.

Check signal between malfunctioning door switch harness connector and ground using oscilloscope.

Is the inspection result normal?

YES-1 >> Back door: GO TO 3.
YES-2 >> Other door: GO TO 4.
NO

>> GO TO 2.

2.

CHECK DOOR SWITCH CIRCUIT

1.

Disconnect BCM connector.

2.

Check continuity between door switch harness connector and BCM harness connector.

Monitor item

Condition

Status

DOOR SW-DR

Driver side door

Open

On

Closed

Off

DOOR SW-AS

Passenger side door

Open

On

Closed

Off

DOOR SW-RL

Rear door LH

Open

On

Closed

Off

DOOR SW-RR

Rear door RH

Open

On

Closed

Off

DOOR SW-BK

Back door

Open

On

Closed

Off

(+)

(–)

Signal

(Reference value)

Door switch

Connector

Terminal

Driver side

B34

2

Ground

7.0 - 8.0 V

Passenger side

B27

Rear LH

B71

Rear RH

B53

Back door

D106

3

PKIB4960J

DLK-88

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

DOOR SWITCH

3.

Check continuity between door switch harness connector and ground.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-93, "Removal and Installation"

.

NO

>> Repair or replace harness.

3.

CHECK BACK DOOR SWITCH CIRCUIT

Check continuity between back door lock assembly harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

4.

CHECK DOOR SWITCH

Refer to

DLK-88, "Component Inspection"

.

Is the inspection result normal?

YES

>> GO TO 5.

NO

>> Replace malfunctioning door switch.

5.

CHECK INTERMITTENT INCIDENT

Refer to

GI-42, "Intermittent Incident"

.

>> INSPECTION END

Component Inspection

INFOID:0000000006302755

1.

CHECK DOOR SWITCH

1.

Turn ignition switch OFF.

2.

Disconnect malfunctioning door switch connector.

3.

Check continuity between door switch terminals.

Door switch

BCM

Continuity

Connector

Terminal

Connector

Terminal

Driver side

B34

2

B10

47

Existed

Passenger side

B27

45

Rear LH

B71

48

Rear RH

B53

46

Back door

D106

3

43

Door switch

Ground

Continuity

Connector

Terminal

Driver side

B34

2

Not existed

Passenger side

B27

Rear LH

B71

Rear RH

B53

Back door

D106

3

Back door lock assembly

Ground

Continuity

Connector

Terminal

D106

4

Existed

DOOR SWITCH

DLK-89

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace malfunction door switch.

Door switch

Condition

Continuity

Terminal

Driver side

2

Ground part of door

switch

Door switch

Pressed

Existed

Released

Not existed

Passenger side

Pressed

Existed

Released

Not existed

Rear LH

Pressed

Existed

Released

Not existed

Rear RH

Pressed

Existed

Released

Not existed

Back door

3

4

Back door lock as-

sembly

Lock

Existed

Unlock

Not existed

DLK-90

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

HAZARD FUNCTION

HAZARD FUNCTION

Component Function Check

INFOID:0000000006302802

1.

CHECK FUNCTION

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.

2.

Select “FLASHER” in “ACTIVE TEST” mode.

3.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Hazard warning lamp circuit is OK.

NO

>> Refer to

DLK-90, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006302803

1.

CHECK HAZARD SWITCH CIRCUIT

Refer to

EXL-72, "Component Function Check"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK INTERMITTENT INCIDENT

Refer to

GI-42, "Intermittent Incident"

.

>> INSPECTION END

Monitor item

Status

FLASHER

LH

Front turn signal lamp LH

Turns ON

RH

Front turn signal lamp RH

Turns ON

OFF

Front turn signal lamp

Turns OFF

INTELLIGENT KEY

DLK-91

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

INTELLIGENT KEY

Component Function Check

INFOID:0000000006302796

1.

CHECK FUNCTION

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.

2.

Select “RKE OPE COUN1” in “DATA MONITOR” mode.

3.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Intelligent Key is OK.

NO

>> Refer to

DLK-91, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006302797

1.

CHECK INTELLIGENT KEY BATTERY

Check by connecting a resistance (approximately 300

Ω

) so that the

current value becomes about 10 mA. Refer to

DLK-193, "Removal

and Installation"

.

Is the measurement value within the specification?

YES

>> Replace Intelligent Key.

NO

>> Replace Intelligent Key battery.

Monitor item

Condition

RKE OPE COUN1

Check that the numerical value is changing while operating on the Intelligent Key.

Standard

: Approx. 2.5 - 3.0 V

OCC0607D

DLK-92

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

INTELLIGENT KEY WARNING BUZZER

INTELLIGENT KEY WARNING BUZZER

Component Function Check

INFOID:0000000006302793

1.

CHECK FUNCTION

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.

2.

Select “OUTSIDE BUZZER” in “ACTIVE TEST” mode.

3.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Intelligent Key warning buzzer is OK.

NO

>> Refer to

DLK-92, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006302794

1.

CHECK FUSE

1.

Turn ignition switch OFF.

2.

Check 10 A fuse, [No. 7, located in fuse block (J/B)].

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Replace the blown fuse after repairing the affected circuit if a fuse is blown.

2.

CHECK INTELLIGENT KEY WARNING BUZZER POWER SUPPLY CIRCUIT

1.

Disconnect Intelligent Key warning buzzer connector.

2.

Check voltage between Intelligent Key warning buzzer harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 3.

NO

>> Repair or replace harness.

3.

CHECK INTELLIGENT KEY WARNING BUZZER CIRCUIT

1.

Disconnect BCM connector.

2.

Check continuity between BCM harness connector and Intelligent Key warning buzzer harness connector.

3.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> Repair or replace harness.

Monitor item

Status

OUTSIDE BUZZER

ON

Outside warning buzzer

Buzzer sounds

OFF

Buzzer does not sound

(+)

(–)

Voltage

(Approx.)

Intelligent Key warning buzzer

Connector

Terminal

E25

1

Ground

Battery voltage

BCM

Intelligent Key warning buzzer

Continuity

Connector

Terminal

Connector

Terminal

M70

93

E25

3

Existed

BCM

Ground

Continuity

Connector

Terminal

M70

93

Not existed

INTELLIGENT KEY WARNING BUZZER

DLK-93

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

4.

CHECK INTELLIGENT KEY WARNING BUZZER

Refer to

DLK-93, "Component Inspection"

.

Is the inspection result normal?

YES

>> Replace BCM. Refer to

BCS-93, "Removal and Installation"

.

NO

>> Replace Intelligent Key warning buzzer.

Component Inspection

INFOID:0000000006302795

1.

CHECK INTELLIGENT KEY WARNING BUZZER

1.

Turn ignition switch OFF.

2.

Disconnect Intelligent Key warning buzzer connector.

3.

Connect battery power supply directly to Intelligent Key warning buzzer terminals and check the opera-
tion.

Is the inspection result normal?

YES

>> INSPECTION END

NO

>> Replace Intelligent Key warning buzzer.

Intelligent Key warning buzzer

Operation

Terminal

(+)

(

−

)

1

3

Buzzer sounds

DLK-94

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

KEY WARNING LAMP

KEY WARNING LAMP

Component Function Check

INFOID:0000000006302800

1.

CHECK FUNCTION

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.

2.

Select “INDICATOR” in “ACTIVE TEST” mode.

3.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Key warning lamp is OK.

NO

>> Refer to

DLK-94, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006302801

1.

CHECK KEY WARNING LAMP

Refer to

MWI-22, "On Board Diagnosis Function"

.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace the malfunctioning parts.

2.

CHECK INTERMITTENT INCIDENT

Refer to

GI-42, "Intermittent Incident"

.

>> INSPECTION END

Monitor item

Status

INDICATOR

KEY ON

Key warning lamp

Turns ON

KEY IND

Blinks

OFF

Turns OFF

REMOTE KEYLESS ENTRY RECEIVER

DLK-95

< DTC/CIRCUIT DIAGNOSIS >

[TYPE 1]

C

D

E

F

G

H

I

J

L

M

A

B

DLK

N

O

P

REMOTE KEYLESS ENTRY RECEIVER

Component Function Check

INFOID:0000000006302785

1.

CHECK FUNCTION

1.

Select “INTELLIGENT KEY” of “BCM” using CONSULT-III.

2.

Select “RKE OPE COUN1” in “DATA MONITOR” mode.

3.

Check that the function operates normally according to the following conditions.

Is the inspection result normal?

YES

>> Remote keyless entry receiver is OK.

NO

>> Refer to

DLK-95, "Diagnosis Procedure"

.

Diagnosis Procedure

INFOID:0000000006302786

1.

CHECK REMOTE KEYLESS ENTRY RECEIVER GROUND CIRCUIT

1.

Turn ignition switch OFF.

2.

Disconnect BCM connector and remote keyless entry receiver connector.

3.

Check continuity between BCM harness connector and remote keyless entry receiver harness connector.

4.

Check continuity between BCM harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 2.

NO

>> Repair or replace harness.

2.

CHECK REMOTE KEYLESS ENTRY RECEIVER POWER SUPPLY

1.

Reconnect BCM connector.

2.

Check voltage between remote keyless entry receiver harness connector and ground.

Is the inspection result normal?

YES

>> GO TO 4.

NO

>> GO TO 3.

3.

CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 1

1.

Disconnect BCM connector

2.

Check continuity between BCM harness connector and remote keyless entry receiver harness connector.

Monitor item

Condition

RKE OPE COUN1

Checks whether value changes when operating Intelligent Key

BCM

Remote keyless entry receiver

Continuity

Connector

Terminal

Connector

Terminal

M68

18

M75

1

Existed

BCM

Ground

Continuity

Connector

Terminal

M68

18

Not existed

(+)

(–)

Voltage

(Approx.)

Remote keyless entry receiver

Connector

Terminal

M75

4

Ground

5 V

BCM

Remote keyless entry receiver

Continuity

Connector

Terminal

Connector

Terminal

M68

19

M75

4

Existed