Juke F15 (2012 year). Service Repair Manual — part 205
EXL-50
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
DAYTIME RUNNING LIGHT RELAY CIRCUIT
DAYTIME RUNNING LIGHT RELAY CIRCUIT
Component Function Check
INFOID:0000000006452120
1.
CHECK DAYTIME RUNNING LIGHT OPERATION
CONSULT-III ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test item, check that parking lamp, tail lamp and license plate lamp are turned ON.
Is the inspection result normal?
YES
>> Daytime running light relay circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000006452121
1.
CHECK DAYTIME RUNNING LIGHT RELAY FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuse is not fusing.
Gasoline engine models
Diesel engine models
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the fuse after repairing the applicable circuit.
2.
CHECK DAYTIME RUNNING LIGHT RELAY POWER SUPPLY
1.
Remove daytime running light relay.
2.
Check voltage between daytime running light relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK DAYTIME RUNNING LIGHT RELAY
Check daytime running light relay. Refer to
EXL-51, "Component Inspection"
Is the inspection result normal?
YES
>> GO TO 4.
TAIL
: Parking lamp, tail lamp and license plate lamp ON
Off
: Parking lamp, tail lamp and license plate lamp OFF
Unit
Fuse No.
Capacity
Daytime running light relay
#24
10 A
#25
#26
Unit
Fuse No.
Capacity
Daytime running light relay
#17
10 A
#31
#33
(+)
(
−
)
Voltage
(Approx.)
Daytime running light relay
Connector
Terminal
E82
1
Ground
Battery voltage
3
6
DAYTIME RUNNING LIGHT RELAY CIRCUIT
EXL-51
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
NO
>> Replace daytime running light relay.
4.
CHECK DAYTIME RUNNING LIGHT RELAY CONTROL SIGNAL OUTPUT
CONSULT-III ACTIVE TEST
1.
Install daytime running light relay.
2.
Turn ignition switch ON.
3.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4.
With operating the test item, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Daytime running light relay circuit is OK.
Fixed at 0 V >>GO TO 5.
Fixed at battery voltage >>Replace IPDM E/R.
5.
CHECK DAYTIME RUNNING LIGHT RELAY CONTROL SIGNAL OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Remove daytime running light relay.
3.
Disconnect IPDM E/R harness connector.
4.
Check continuity between IPDM E/R harness connector and daytime running light relay harness connec-
tor.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK DAYTIME RUNNING LIGHT RELAY CONTROL SIGNAL SHORT CIRCUIT
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace harness.
Component Inspection
INFOID:0000000006452122
1.
CHECK DAYTIME RUNNING LIGHT RELAY
1.
Turn ignition switch OFF.
2.
Remove daytime running light relay.
3.
Apply battery voltage to daytime running light relay between terminals 1 and 2.
4.
Check continuity of daytime running light relay.
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
E13
28
Ground
EXTERNAL
LAMPS
TAIL
0 V
Off
Battery voltage
IPDM E/R
Daytime running light relay
Continuity
Connector
Terminal
Connector
Terminal
E13
28
E82
2
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E13
28
Not existed
EXL-52
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
DAYTIME RUNNING LIGHT RELAY CIRCUIT
Is the inspection result normal?
YES
>> Daytime running light relay is normal.
NO
>> Replace daytime running light relay.
Daytime running light relay
Condition
Continuity
Terminal
3
5
Voltage
Apply
Existed
Not Apply
Not existed
6
7
Apply
Existed
Not Apply
Not existed
HEADLAMP AIMING SYSTEM (MANUAL)
EXL-53
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
HEADLAMP AIMING SYSTEM (MANUAL)
Component Inspection
INFOID:0000000006451723
1.
CHECK HEADLAMP AIMING SWITCH
1.
Remove headlamp aiming switch.
2.
Check resistance among each headlamp aiming switch terminal.
Is the inspection result normal?
YES
>> Headlamp aiming switch is normal.
NO
>> Replace the headlamp aiming switch.
Headlamp aiming switch
Condition
Resistance
(Approx.)
Terminal
Switch position
1
2
0
A: 160
Ω
1
B: 300
Ω
2
C: 392
Ω
3
D: 499
Ω
3
—
E: 390
Ω
JSLIA0084ZZ
EXL-54
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
FRONT FOG LAMP CIRCUIT
FRONT FOG LAMP CIRCUIT
Component Function Check
INFOID:0000000006452123
1.
CHECK FRONT FOG LAMP OPERATION
CONSULT-III ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the front fog lamp is turned ON.
Is the measurement normal?
YES
>> Front fog lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000006452124
1.
CHECK FRONT FOG LAMP FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuse is not fusing.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK FRONT FOG LAMP SHORT CIRCUIT
1.
Disconnect front fog connector and IPDM E/R connector.
2.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace fuse. (Replace IPDM E/R if the fuse is fusing again.)
NO
>> Repair or replace harness. And then replace the fuse.
3.
CHECK FRONT FOG LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace bulb.
4.
CHECK FRONT FOG LAMP OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1.
Disconnect front fog lamp connector.
2.
Turn ignition switch ON.
3.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4.
With operating the test items, check the voltage between IPDM E/R harness connector and ground.
Fog
: Front fog lamp ON
Off
: Front fog lamp OFF
Unit
Location
Fuse No.
Capacity
Front fog lamp
IPDM E/R
#50
15 A
IPDM E/R
Ground
Continuity
Connector
Terminal
RH
E12
19
Not existed
LH
20
FRONT FOG LAMP CIRCUIT
EXL-55
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace IPDM E/R.
5.
CHECK FRONT FOG LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and front fog lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK FRONT FOG LAMP GROUND CIRCUIT OPEN CIRCUIT
Check continuity between front fog lamp harness connector and ground.
Is the inspection result normal?
YES
>> Refer to
GI-42, "Intermittent Incident"
.
NO
>> Repair or replace harness.
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
RH
E12
19
Ground
EXTERNAL
LAMPS
Fog
Battery voltage
Off
0 V
LH
20
Fog
Battery voltage
Off
0 V
IPDM E/R
Front fog lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E12
19
E48
1
Existed
LH
20
E30
Front fog lamp
Ground
Continuity
Connector
Terminal
RH
E48
2
Existed
LH
E30
EXL-56
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
REAR FOG LAMP CIRCUIT
REAR FOG LAMP CIRCUIT
Component Function Check
INFOID:0000000006451728
1.
CHECK REAR FOG LAMP OPERATION
CONSULT-III ACTIVE TEST
1.
Select “RR FOG LAMP” of BCM (HEAD LAMP) active test item.
2.
With operating the test items, check that the rear fog lamp is turned ON.
Is the inspection result normal?
YES
>> Rear fog lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000006451729
1.
CHECK REAR FOG LAMP BULB
Check applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace bulb.
2.
CHECK REAR FOG LAMP OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1.
Turn ignition switch OFF.
2.
Disconnect rear fog lamp connector.
3.
Turn ignition switch ON.
4.
Select “RR FOG LAMP” of BCM (HEAD LAMP) active test item.
5.
With operating the test items, check voltage between rear fog lamp harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> GO TO 3.
3.
CHECK REAR FOG LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and rear fog lamp harness connector.
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES
>> GO TO 4.
On
: Rear fog lamp ON
Off
: Rear fog lamp OFF
(+)
(
−
)
Test item
Voltage
(Approx.)
Rear fog lamp
Connector
Terminal
B85
1
Ground
RR FOG LAMP
On
12 V
Off
0 V
BCM
Rear fog lamp
Continuity
Connector
Terminal
Connector
Terminal
B9*
1
B10*
2
51*
1
52*
2
B85
1
Existed
REAR FOG LAMP CIRCUIT
EXL-57
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
NO
>> Repair or replace harness.
4.
CHECK REAR FOG LAMP SHORT CIRCUIT
Check continuity between BCM harness connector and ground.
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES
>> Check bulb socket for internal short circuit, and if check result is normal, replace BCM. Refer to
BCS-93, "Removal and Installation"
(with Intelligent Key),
BCS-161, "Removal and Installation"
(without Intelligent Key).
NO
>> Repair or replace harness.
5.
CHECK REAR FOG LAMP GROUND OPEN CIRCUIT
Check continuity between rear fog lamp harness connector and ground.
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
BCM
Ground
Continuity
Connector
Terminal
B9*
1
B10*
2
51*
1
52*
2
Not existed
Rear fog lamp
Ground
Continuity
Connector
Terminal
B85
2
Existed
EXL-58
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
PARKING LAMP CIRCUIT
PARKING LAMP CIRCUIT
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
INFOID:0000000006452125
1.
CHECK PARKING LAMP OPERATION
CONSULT-III ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the parking lamp is turned ON.
Is the inspection result normal?
YES
>> Parking lamp circuit is normal.
NO
>> Refer to
EXL-60, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure"
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
INFOID:0000000006452126
1.
CHECK PARKING LAMP FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuses are not fusing.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK PARKING LAMP SHORT CIRCUIT
1.
Disconnect the following connectors.
-
IPDM E/R
-
Parking lamp
-
Rear combination lamp (RH)
-
License plate lamp
2.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace fuse. (Replace IPDM E/R if fusing is found again.)
NO
>> Repair or replace harness. And then replace the fuse.
3.
CHECK PARKING LAMP BULB
Check applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Replace bulb.
4.
CHECK PARKING LAMP OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1.
Disconnect parking lamp connector.
TAIL
: Parking lamp ON
Off
: Parking lamp OFF
Unit
Location
Fuse No.
Capacity
Parking lamp
IPDM E/R
#46
10 A
IPDM E/R
Ground
Continuity
Connector
Terminal
E14
37
Not existed
38
PARKING LAMP CIRCUIT
EXL-59
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
2.
Turn ignition switch ON.
3.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4.
With operating the test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace IPDM E/R.
5.
CHECK PARKING LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and parking lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK PARKING LAMP GROUND OPEN CIRCUIT
Check continuity between parking lamp harness connector and ground.
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
WITH DAYTIME RUNNING LIGHT SYSTEM
WITH DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
INFOID:0000000006452127
1.
CHECK PARKING LAMP OPERATION
CONSULT-III ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the parking lamp is turned ON.
Is the inspection result normal?
YES
>> Parking lamp circuit is normal.
NO
>> Refer to
EXL-60, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure"
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
E14
37
Ground
EXTERNAL
LAMPS
TAIL
Battery voltage
Off
0 V
IPDM E/R
Parking lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E14
37
E43
1
Existed
LH
E24
Parking lamp
Ground
Continuity
Connector
Terminal
RH
E43
2
Existed
LH
E24
TAIL
: Parking lamp ON
Off
: Parking lamp OFF
EXL-60
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
PARKING LAMP CIRCUIT
WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
INFOID:0000000006452128
1.
CHECK PARKING LAMP BULB
Check applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace bulb.
2.
CHECK PARKING LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Remove daytime running light relay.
3.
Disconnect parking lamp connector.
4.
Check continuity between daytime running light relay harness connector and parking lamp harness con-
nector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK PARKING LAMP SHORT CIRCUIT
1.
Disconnect the following connectors.
-
Rear combination lamp (RH)
-
License plate lamp
2.
Check continuity between daytime running light relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK PARKING LAMP GROUND OPEN CIRCUIT
Check continuity between parking lamp harness connector and ground.
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
Daytime running light relay
Parking lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E82
5
E43
1
Existed
LH
E24
Daytime running light relay
Ground
Continuity
Connector
Terminal
E82
5
Not existed
Parking lamp
Ground
Continuity
Connector
Terminal
RH
E43
2
Existed
LH
E24
TAIL LAMP CIRCUIT
EXL-61
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
TAIL LAMP CIRCUIT
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
INFOID:0000000006452129
1.
CHECK TAIL LAMP OPERATION
CONSULT-III ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the tail lamp is turned ON.
Is the inspection result normal?
YES
>> Tail lamp circuit is normal.
NO
>> Refer to
EXL-61, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure"
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
INFOID:0000000006452130
1.
CHECK TAIL LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace bulb.
2.
CHECK PARKING LAMP OPERATION
Check that the parking lamp is turned ON.
Is the inspection result normal?
YES-1 (When tail lamp (RH) does not turn ON.)>>GO TO 6.
YES-2 (When tail lamp (LH) does not turn ON.)>>GO TO 3.
NO
>> Check parking lamp circuit. Refer to
EXL-58, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM :
.
3.
CHECK TAIL LAMP (LH) FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuses are not fusing.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 5.
4.
CHECK TAIL LAMP (LH) OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1.
Disconnect rear combination lamp (LH) connector.
2.
Turn ignition switch ON.
3.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4.
With operating the test items, check voltage between IPDM E/R harness connector and ground.
TAIL
: Tail Lamp ON
Off
: Tail lamp OFF
Unit
Location
Fuse No.
Capacity
Tail lamp (LH)
IPDM E/R
#47
10 A
EXL-62
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
TAIL LAMP CIRCUIT
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Replace IPDM E/R.
5.
CHECK TAIL LAMP (LH) SHORT CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector and rear combination lamp (LH) connector.
3.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace fuse. (Replace IPDM E/R if fusing is found again.)
NO
>> Repair or replace harness. And then replace the fuse.
6.
CHECK TAIL LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector and rear combination lamp connector.
3.
Check continuity between IPDM E/R harness connector and rear combination lamp harness connector.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
CHECK TAIL LAMP GROUND OPEN CIRCUIT
Check continuity between rear combination lamp harness connector and ground.
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
WITH DAYTIME RUNNING LIGHT SYSTEM
WITH DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
INFOID:0000000006478922
1.
CHECK TAIL LAMP OPERATION
CONSULT-III ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the test items, check that the tail lamp is turned ON.
(+)
(
−
)
Test item
Voltage
(Approx.)
IPDM E/R
Connector
Terminal
E14
44
Ground
EXTERNAL
LAMPS
TAIL
Battery voltage
Off
0 V
IPDM E/R
Ground
Continuity
Connector
Terminal
E14
44
Not existed
IPDM E/R
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E14
38
B59
2
Existed
LH
44
B80
Rear combination lamp
Ground
Continuity
Connector
Terminal
RH
B59
3
Existed
LH
B80
TAIL LAMP CIRCUIT
EXL-63
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Is the inspection result normal?
YES
>> Tail lamp circuit is normal.
NO
>> Refer to
EXL-63, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure"
WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
INFOID:0000000006478923
1.
CHECK TAIL LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace bulb.
2.
CHECK PARKING LAMP OPERATION
Check that the parking lamp is turned ON.
Is the inspection result normal?
YES-1 (When tail lamp (RH) does not turn ON.)>>GO TO 4.
YES-2 (When tail lamp (LH) does not turn ON.)>>GO TO 3.
NO
>> Check parking lamp circuit. Refer to
EXL-59, "WITH DAYTIME RUNNING LIGHT SYSTEM :
.
3.
CHECK TAIL LAMP (LH) SHORT CIRCUIT
1.
Turn ignition switch OFF.
2.
Remove daytime running light relay.
3.
Disconnect rear combination lamp (LH) connector.
4.
Check continuity between daytime running light relay harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK TAIL LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Remove daytime running light relay.
3.
Disconnect rear combination lamp connector.
4.
Check continuity between daytime running light relay harness connector and rear combination lamp har-
ness connector.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
5.
CHECK TAIL LAMP GROUND OPEN CIRCUIT
Check continuity between rear combination lamp harness connector and ground.
TAIL
: Tail Lamp ON
Off
: Tail lamp OFF
Daytime running light relay
Ground
Continuity
Connector
Terminal
E82
7
Not existed
Daytime running light relay
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
E82
5
B59
2
Existed
LH
7
B80
EXL-64
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
TAIL LAMP CIRCUIT
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
Rear combination lamp
Ground
Continuity
Connector
Terminal
RH
B59
3
Existed
LH
B80
LICENSE PLATE LAMP CIRCUIT
EXL-65
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LICENSE PLATE LAMP CIRCUIT
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
INFOID:0000000006452133
1.
CHECK TAIL LAMP (RH) OPERATION
Check that the tail lamp (RH) is turned ON.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check tail lamp circuit. Refer to
EXL-61, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM :
.
2.
CHECK LICENSE PLATE LAMP OPERATION
CONSULT-III ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the lighting switch, check that the license plate lamp is turned ON.
Is the inspection result normal?
YES
>> License plate lamp circuit is normal.
NO
>> Refer to
EXL-65, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure"
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
INFOID:0000000006452134
1.
CHECK LICENSE PLATE LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace bulb.
2.
CHECK LICENSE PLATE LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector and back door opener switch connector.
3.
Check continuity between IPDM E/R harness connector and back door opener switch harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK LICENSE PLATE LAMP GROUND OPEN CIRCUIT
Check continuity between back door opener switch harness connector and ground.
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
WITH DAYTIME RUNNING LIGHT SYSTEM
TAIL
: License plate lamp ON
Off
: License plate lamp OFF
IPDM E/R
Back door opener switch
Continuity
Connector
Terminal
Connector
Terminal
E14
38
D107
5
Existed
Back door opener switch
Ground
Continuity
Connector
Terminal
D107
6
Existed
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст