Juke F15 (2012 year). Service Repair Manual — part 206
EXL-66
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
LICENSE PLATE LAMP CIRCUIT
WITH DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
INFOID:0000000006478924
1.
CHECK TAIL LAMP (RH) OPERATION
Check that the tail lamp (RH) is turned ON.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check tail lamp circuit. Refer to
EXL-62, "WITH DAYTIME RUNNING LIGHT SYSTEM : Compo-
2.
CHECK LICENSE PLATE LAMP OPERATION
CONSULT-III ACTIVE TEST
1.
Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2.
With operating the lighting switch, check that the license plate lamp is turned ON.
Is the inspection result normal?
YES
>> License plate lamp circuit is normal.
NO
>> Refer to
EXL-66, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure"
WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
INFOID:0000000006478925
1.
CHECK LICENSE PLATE LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace bulb.
2.
CHECK LICENSE PLATE LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Remove daytime running light relay.
3.
Disconnect back door opener switch connector.
4.
Check continuity between daytime running light relay harness connector and back door opener switch
harness connector.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK LICENSE PLATE LAMP GROUND OPEN CIRCUIT
Check continuity between back door opener switch harness connector and ground.
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
TAIL
: License plate lamp ON
Off
: License plate lamp OFF
Daytime running light relay
Back door opener switch
Continuity
Connector
Terminal
Connector
Terminal
E82
5
D107
5
Existed
Back door opener switch
Ground
Continuity
Connector
Terminal
D107
6
Existed
LIGHT & RAIN SENSOR
EXL-67
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
LIGHT & RAIN SENSOR
Component Function Check
INFOID:0000000006452196
1.
CHECK LIGHT & RAIN SENSOR
1.
Clean light & rain sensor detection area of windshield fully.
2.
Turn ignition switch ON.
3.
Turn lighting switch AUTO.
4.
With the light & rain sensor illuminating, check the auto light function.
Is the inspection result normal?
YES
>> Light & rain sensor is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000006452197
1.
CHECK LIGHT & RAIN SENSOR FUSE
1.
Turn ignition switch OFF.
2.
Check that the following fuse is not fusing.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace the fuse after repairing the applicable circuit.
2.
CHECK LIGHT & RAIN SENSOR POWER SUPPLY
1.
Disconnect light & rain sensor connector.
2.
Check voltage between light & rain sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK LIGHT & RAIN SENSOR GROUND CIRCUIT
Check continuity between light & rain sensor harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK LIGHT & RAIN SENSOR SIGNAL
1.
Connect light & rain sensor connector.
2.
Turn ignition switch ON.
Condition
Auto light function
Light & rain sensor
When illuminating
Not operating
When shutting off light
Operating
Unit
Fuse No.
Capacity
Light & rain sensor
#7
10 A
(+)
(
−
)
Voltage
(Approx.)
Light & rain sensor
Connector
Terminal
R5
1
Ground Battery
voltage
Light & rain sensor
Ground
Continuity
Connector
Terminal
R5
3
Existed
EXL-68
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
LIGHT & RAIN SENSOR
3.
Check signal between BCM harness connector and ground with oscilloscope.
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES
>> Replace light & rain sensor.
NO
>> GO TO 5.
5.
CHECK LIGHT & RAIN SENSOR SIGNAL CIRCUIT FOR OPEN
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and light & rain sensor connector.
3.
Check continuity between BCM harness connector and light & rain sensor harness connector.
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK LIGHT & RAIN SENSOR SIGNAL CIRCUIT FOR SHORT
Check continuity between BCM harness connector and ground.
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES
>> Refer to
BCS-93, "Removal and Installation"
(with Intelligent Key),
(without Intelligent Key).
NO
>> Repair or replace harness.
(+)
(
−
)
Condition
Signal
(Reference value)
BCM
Connector
Terminal
M65*
1
M68*
2
14*
1
11*
2
Ground Ignition
switch
ON
Approx. 8.7V
JPMIA0156GB
BCM
Light & rain sensor
Continuity
Connector
Terminal
Connector
Terminal
M65*
1
M68*
2
14*
1
11*
2
R5
2
Existed
BCM
Ground
Continuity
Connector
Terminal
M65*
1
M68*
2
14*
1
11*
2
Not existed
TURN SIGNAL LAMP CIRCUIT
EXL-69
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
TURN SIGNAL LAMP CIRCUIT
Component Function Check
INFOID:0000000006451732
1.
CHECK TURN SIGNAL LAMP
CONSULT-III ACTIVE TEST
1.
Select “FLASHER” of BCM (FLASHER) active test item.
2.
With operating the test items, check that the turn signal lamps is turned ON.
Is the inspection result normal?
YES
>> Turn signal lamp circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000006451733
1.
CHECK TURN SIGNAL LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Replace bulb.
2.
CHECK TURN SIGNAL LAMP OUTPUT VOLTAGE
1.
Turn ignition switch OFF.
2.
Disconnect front turn signal lamp connector, side turn signal lamp connector and rear combination lamp
connector.
3.
Turn ignition switch ON.
4.
With operating the turn signal switch, check voltage between BCM harness connector and ground.
*
1
: Without Intelligent Key
*
2
: With Intelligent Key
LH
: Turn signal lamps (LH) ON
RH
: Turn signal lamps (RH) ON
Off
: Turn signal lamps OFF
(+)
(–)
Condition
Voltage
(Approx.)
BCM
Connector
Terminal
B9*
1
M69*
2
49*
1
60*
2
Ground
Turn signal
switch
LH
OFF
0 V
48*
1
61*
2
RH
OFF
0 V
PKID0926E
PKID0926E
EXL-70
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
TURN SIGNAL LAMP CIRCUIT
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
CHECK TURN SIGNAL LAMP OPEN CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector.
3.
Check continuity between BCM harness connector and front turn signal lamp, side turn signal lamp or rear
combination lamp harness connector.
Front turn signal lamp
Side turn signal lamp
Rear turn signal lamp
*
1
: Without Intelligent Key
*
2
: With Intelligent Key
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace harness.
4.
CHECK TURN SIGNAL LAMP SHORT CIRCUIT
Check continuity between BCM harness connector and ground.
*
1
: Without Intelligent Key
*
2
: With Intelligent Key
Is the inspection result normal?
BCM
Front turn signal lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
B9*
1
M69*
2
48*
1
61*
2
E46
1
Existed
LH
49*
1
60*
2
E27
BCM
Side turn signal lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
B9*
1
M69*
2
48*
1
61*
2
E40
1
Existed
LH
49*
1
60*
2
E23
BCM
Rear combination lamp
Continuity
Connector
Terminal
Connector
Terminal
RH
B9*
1
M69*
2
48*
1
61*
2
B59
5
Existed
LH
49*
1
60*
2
B80
BCM
Ground
Continuity
Connector
Terminal
RH
B9
*1
M69
*2
48*
1
61*
2
Not existed
LH
49*
1
60*
2
TURN SIGNAL LAMP CIRCUIT
EXL-71
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
YES
>> Check each bulb socket for internal short circuit, and if check result is normal, replace BCM. Refer
to
BCS-93, "Removal and Installation"
(with Intelligent Key),
BCS-161, "Removal and Installation"
(without Intelligent Key).
NO
>> Repair or replace harness.
5.
CHECK TURN SIGNAL LAMP GROUND OPEN CIRCUIT
Check continuity between BCM harness connector and front turn signal lamp, side turn signal lamp or rear
combination lamp and ground.
Front turn signal lamp
Side turn signal lamp
Rear turn signal lamp
Is the inspection result normal?
YES
>> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO
>> Repair or replace harness.
Front turn signal lamp
Ground
Continuity
Connector
Terminal
RH
E46
2
Existed
LH
E27
Side turn signal lamp
Ground
Continuity
Connector
Terminal
RH
E40
2
Existed
LH
E23
Rear combination lamp
Ground
Continuity
Connector
Terminal
RH
B59
3
Existed
LH
B80
EXL-72
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
HAZARD SWITCH
HAZARD SWITCH
Component Function Check
INFOID:0000000006451734
1.
CHECK HAZARD SWITCH SIGNAL BY CONSULT-III
CONSULT-III DATA MONITOR
1.
Turn the ignition switch ON.
2.
Select “HAZARD SW” of BCM (FLASHER) data monitor item.
3.
With operating the hazard switch, check the monitor status.
Is the inspection result normal?
YES
>> Hazard switch circuit is normal.
NO
>> Refer to
.
Diagnosis Procedure
INFOID:0000000006451735
1.
CHECK HAZARD SWITCH SIGNAL INPUT
1.
Turn ignition switch OFF.
2.
Disconnect hazard switch connector.
3.
Check voltage between hazard switch connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 2.
2.
CHECK HAZARD SWITCH SIGNAL OPEN CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between hazard switch harness connector and BCM harness connector.
*1: Without Intelligent Key
*2: With Intelligent Key
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace harness.
3.
CHECK HAZARD SWITCH SIGNAL SHORT CIRCUIT
Check continuity between hazard switch harness connector and ground.
Is the inspection result normal?
Monitor item
Condition
Monitor status
HAZARD SW
Hazard switch
ON
On
OFF
Off
(+)
(
−
)
Voltage (Approx.)
Hazard switch
Connector
Terminal
M45
2
Ground
12 V
Hazard switch
BCM
Continuity
Connector
Terminal
Connector
Terminal
M45
2
M65
*1
M68
*2
29
Existed
Hazard switch
Ground
Continuity
Connector
Terminal
M45
2
Not existed
HAZARD SWITCH
EXL-73
< DTC/CIRCUIT DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
YES
>> Replace BCM. Refer to
BCS-93, "Removal and Installation"
(with Intelligent Key) or
(without Intelligent Key).
NO
>> Repair or replace harness.
4.
CHECK HAZARD SWITCH GROUND OPEN CIRCUIT
Check continuity between hazard switch harness connector and ground.
Is the inspection result normal?
YES
>> Replace hazard switch.
NO
>> Repair or replace harness.
Hazard switch
Ground
Continuity
Connector
Terminal
M45
1
Existed
EXL-74
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
EXTERIOR LIGHTING SYSTEM SYMPTOMS
SYMPTOM DIAGNOSIS
EXTERIOR LIGHTING SYSTEM SYMPTOMS
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Symptom Table
INFOID:0000000006451740
CAUTION:
Perform the self-diagnosis with CONSULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.
Symptom
Possible cause
Inspection item
Headlamp (HI) is not
turned ON.
One side
• Fuse
• Halogen bulb
• Harness between IPDM E/R and
headlamp
• Harness between headlamp and
ground
• IPDM E/R
Headlamp (HI) circuit
Refer to
.
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to
High beam indicator lamp is not turned ON.
[Headlamp (HI) is turned ON.]
Combination meter
• Combination meter
Data monitor “HI-BEAM IND”
• BCM (HEADLAMP)
Active test “HEADLAMP”
Headlamp (LO) is not
turned ON.
One side
• Fuse
• Halogen bulb
• Harness between IPDM E/R and
headlamp
• Harness between headlamp and
ground
• IPDM E/R
Headlamp (LO) circuit
Refer to
.
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to
Headlamp is not turned
OFF.
When ignition switch
is turned ON.
When ignition switch
is turned OFF.
IPDM E/R
—
Headlamp HI and LO are not turned ON.
• Harness between headlamp and
ground
• Halogen bulb
Headlamp ground circuit
Refer to
Front fog lamp is not
turned ON.
One side
• Front fog lamp bulb
• Harness between front fog lamp
relay and front fog lamp
Front fog lamp circuit
Refer to
.
Both side
Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to
Front fog lamp is not turned OFF.
Parking lamp is not turned ON.
• Parking lamp bulb
• Harness between IPDM E/R and
parking lamp
• IPDM E/R
Parking lamp circuit
Refer to
TIME RUNNING LIGHT SYSTEM :
Component Function Check"
Tail lamp is not turned ON.
• Tail lamp bulb
• Harness between IPDM E/R and
rear combination lamp
• IPDM E/R
Tail lamp circuit
Refer to
TIME RUNNING LIGHT SYSTEM :
Component Function Check"
License plate lamp is not turned ON.
• License plate lamp bulb
• Harness between IPDM E/R and
license plate lamp
License plate lamp circuit
Refer to
EXTERIOR LIGHTING SYSTEM SYMPTOMS
EXL-75
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
WITH DAYTIME RUNNING LIGHT SYSTEM
WITH DAYTIME RUNNING LIGHT SYSTEM : Symptom Table
INFOID:0000000006479243
CAUTION:
Perform the self-diagnosis with CONSULT-III before the symptom diagnosis. Perform the trouble diag-
nosis if any DTC is detected.
• Parking lamp, tail lamp and license plate lamp
are not turned ON.
• Parking lamp, tail lamp and license plate lamp
are not turned OFF.
(Each illumination is turned ON/OFF.)
Symptom diagnosis
“PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON”
Refer to
EXL-80, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Di-
Turn signal lamp does
not blink.
Indicator lamp is nor-
mal.
(Applicable side per-
forms the high flasher
activation.)
• Harness between BCM and each
turn signal lamp
• Turn signal lamp bulb
Turn signal lamp circuit
Refer to
.
Indicator lamp is in-
cluded.
• Combination switch
• Harness between combination
switch and BCM
• BCM
Turn signal indicator
lamp does not blink.
(Turn signal indicator
lamp is normal.)
One side
Combination meter
—
Both sides
(Always)
• Turn signal indicator lamp signal
- BCM
• Combination meter
• Combination meter
Data monitor “TURN IND”
• BCM (FLASHER)
Active test “FLASHER”
Both sides
(Only when activating
hazard warning lamp
with the ignition switch
OFF.)
• Combination meter power supply
and ground circuit
• Combination meter
Combination meter
Power supply and ground circuit
Refer to
.
• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)
• Hazard switch
• Harness between hazard switch
and BCM
• BCM
.
Rear fog lamp is not
turned ON.
Rear fog lamp indica-
tor lamp is normal.
• Harness between BCM and rear
fog lamp
• Rear fog lamp bulb
• BCM
Rear fog lamp circuit
Refer to
.
Rear fog lamp indica-
tor lamp is included.
• Combination switch
• Harness between combination
switch and BCM
• BCM
Rear fog lamp indicator lamp is not turn ON.
(Rear fog lamp turns ON)
• Rear fog lamp status signal
• Combination meter
• BCM
• Combination meter
Data monitor “RR FOG IND”
• BCM (HEAD LAMP)
Active test “RR FOG LAMP”
Symptom
Possible cause
Inspection item
EXL-76
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
EXTERIOR LIGHTING SYSTEM SYMPTOMS
Symptom
Possible cause
Inspection item
Headlamp (HI) is not
turned ON.
One side
• Fuse
• Halogen bulb
• Harness between IPDM E/R and
headlamp
• Harness between headlamp and
ground
• IPDM E/R
Headlamp (HI) circuit
Refer to
.
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON”
Refer to
High beam indicator lamp is not turned ON.
[Headlamp (HI) is turned ON.]
Combination meter
• Combination meter
Data monitor “HI-BEAM IND”
• BCM (HEADLAMP)
Active test “HEADLAMP”
Headlamp (LO) is not
turned ON.
One side
• Fuse
• Halogen bulb
• Harness between IPDM E/R and
headlamp
• Harness between headlamp and
ground
• IPDM E/R
Headlamp (LO) circuit
Refer to
.
Both sides
Symptom diagnosis
“BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON”
Refer to
Headlamp is not turned
OFF.
When ignition switch
is turned ON.
When ignition switch
is turned OFF.
IPDM E/R
—
Headlamp HI and LO are not turned ON.
• Harness between headlamp and
ground
• Halogen bulb
Headlamp ground circuit
Refer to
Front fog lamp is not
turned ON.
One side
• Front fog lamp bulb
• Harness between front fog lamp
relay and front fog lamp
Front fog lamp circuit
Refer to
.
Both side
Symptom diagnosis
“BOTH SIDE FRONT FOG LAMPS ARE NOT TURNED ON”
Refer to
Front fog lamp is not turned OFF.
Parking lamp is not turned ON.
Daytime running light relay
Daytime running light relay circuit
Refer to
.
• Parking lamp bulb
• Harness between parking lamp
and daytime running relay
• IPDM E/R
Parking lamp circuit
Refer to
RUNNING LIGHT SYSTEM : Com-
ponent Function Check"
Tail lamp is not turned ON.
Daytime running light relay
Daytime running light relay circuit
Refer to
.
• Tail lamp bulb
• Harness between daytime run-
ning relay and rear combination
lamp
Tail lamp circuit
Refer to
RUNNING LIGHT SYSTEM : Com-
ponent Function Check"
License plate lamp is not turned ON.
Daytime running light relay
Daytime running light relay circuit
Refer to
.
• License plate lamp bulb
• Harness between daytime run-
ning relay and license plate lamp
License plate lamp circuit
Refer to
EXTERIOR LIGHTING SYSTEM SYMPTOMS
EXL-77
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
• Parking lamp, tail
lamp, lamp and the li-
cense plate lamp are
not turned ON.
• Parking lamp, tail
lamp, lamp and li-
cense plate lamp are
not turned OFF.
Each illumination is
turned ON/OFF
• Fuse
• Harness between IPDM E/R and
the daytime running light relay
• Daytime running light relay
• IPDM E/R
Daytime running light relay circuit
Refer to
.
Each illumination is
not turned ON/OFF
Symptom diagnosis
“PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON”
Refer to
EXL-80, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis
.
Turn signal lamp does
not blink.
Indicator lamp is nor-
mal.
(Applicable side per-
forms the high flasher
activation.)
• Harness between BCM and each
turn signal lamp
• Turn signal lamp bulb
Turn signal lamp circuit
Refer to
.
Indicator lamp is in-
cluded.
• Combination switch
• Harness between combination
switch and BCM
• BCM
Turn signal indicator
lamp does not blink.
(Turn signal indicator
lamp is normal.)
One side
Combination meter
—
Both sides
(Always)
• Turn signal indicator lamp signal
- BCM
• Combination meter
• Combination meter
Data monitor “TURN IND”
• BCM (FLASHER)
Active test “FLASHER”
Both sides
(Only when activating
hazard warning lamp
with the ignition switch
OFF.)
• Combination meter power supply
and ground circuit
• Combination meter
Combination meter
Power supply and ground circuit
Refer to
.
• Hazard warning lamp does not activate.
• Hazard warning lamp continues activating.
(Turn signal is normal.)
• Hazard switch
• Harness between hazard switch
and BCM
• BCM
.
Rear fog lamp is not
turned ON.
Rear fog lamp indica-
tor lamp is normal.
• Harness between BCM and rear
fog lamp
• Rear fog lamp bulb
• BCM
Rear fog lamp circuit
Refer to
.
Rear fog lamp indica-
tor lamp is included.
• Combination switch
• Harness between combination
switch and BCM
• BCM
Rear fog lamp indicator lamp is not turn ON.
(Rear fog lamp turns ON)
• Rear fog lamp status signal
• Combination meter
• BCM
• Combination meter
Data monitor “RR FOG IND”
• BCM (HEAD LAMP)
Active test “RR FOG LAMP”
Symptom
Possible cause
Inspection item
EXL-78
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
BOTH SIDE HEADLAMPS (HI) ARE NOT TURNED ON
Description
INFOID:0000000006451741
Both side headlamps (HI) are not turned ON when setting to the lighting switch HI or PASS.
Diagnosis Procedure
INFOID:0000000006451742
1.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (HI) REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1.
Select “HL HI REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
BCS-93, "Removal and Installation"
(with Intelligent Key),
(without Intelligent Key).
3.
HEADLAMP (HI) CIRCUIT INSPECTION
Check the headlamp (HI) circuit. Refer to
EXL-45, "Component Function Check"
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
HL HI REQ
Lighting switch
(2ND)
HI or PASS
ON
LO
OFF
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
EXL-79
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
BOTH SIDE HEADLAMPS (LO) ARE NOT TURNED ON
Description
INFOID:0000000006451743
Both side headlamps (LO) are not turned ON in any condition.
Diagnosis Procedure
INFOID:0000000006451744
1.
CHECK COMBINATION SWITCH
Check the combination switch. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK HEADLAMP (LO) REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1.
Select “HL LO REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES
>> GO TO 3.
NO
BCS-93, "Removal and Installation"
(with Intelligent Key),
(without Intelligent Key).
3.
HEADLAMP (LO) CIRCUIT INSPECTION
Check the headlamp (LO) circuit. Refer to
EXL-47, "Component Function Check"
.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace the malfunctioning part.
Monitor item
Condition
Monitor status
HL LO REQ
Lighting switch
2ND
ON
OFF
OFF
EXL-80
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
WITHOUT DAYTIME RUNNING LIGHT SYSTEM
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Description
INFOID:0000000006451745
The parking, license plate, tail lamps and each illumination are not turned ON in any condition.
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
INFOID:0000000006451746
1.
COMBINATION SWITCH INSPECTION
Check the combination switch. Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1.
Select “TAIL & CLR REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Replace BCM. Refer to
BCS-93, "Removal and Installation"
(with Intelligent Key),
(without Intelligent Key).
WITH DAYTIME RUNNING LIGHT SYSTEM
WITH DAYTIME RUNNING LIGHT SYSTEM : Description
INFOID:0000000006452140
The parking, license plate, tail lamps and each illumination are not turned ON in any condition.
WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
INFOID:0000000006452141
1.
COMBINATION SWITCH INSPECTION
Check combination switch. Refer to
Is the combination switch normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning part.
2.
CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT
CONSULT-III DATA MONITOR
1.
Select “TAIL & CLR REQ” of IPDM E/R data monitor item.
2.
With operating the lighting switch, check the monitor status.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Replace BCM. Refer to
BCS-93, "Removal and Installation"
(with Intelligent Key),
(without Intelligent Key).
3.
DAYTIME RUNNING LIGHT RELAY CIRCUIT INSPECTION
Monitor item
Condition
Monitor status
TAIL & CLR REQ
Lighting switch
1ST
ON
OFF
OFF
Monitor item
Condition
Monitor status
TAIL & CLR REQ
Lighting switch
1ST
On
OFF
Off
PARKING, LICENSE PLATE AND TAIL LAMPS ARE NOT TURNED ON
EXL-81
< SYMPTOM DIAGNOSIS >
[HALOGEN TYPE]
C
D
E
F
G
H
I
J
K
M
A
B
EXL
N
O
P
Check the daytime running light relay circuit. Refer to
EXL-50, "Component Function Check"
Is the inspection result normal?
YES
>> Replace IPDM E/R.
NO
>> Repair or replace the malfunctioning part.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст