Juke F15 (2012 year). Service Repair Manual — part 382

WCS

SYSTEM

WCS-11

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

TIMING CHART

SOUND SPECIFICATION

PARKING BRAKE RELEASE WARNING CHIME

PARKING BRAKE RELEASE WARNING CHIME : System Diagram

INFOID:0000000006501850

PARKING BRAKE RELEASE WARNING CHIME : System Description

INFOID:0000000006501851

WARNING OPERATION CONDITIONS

If all of the following conditions are fulfilled.

JSNIA2427GB

JSNIA3639GB

JSNIA2422GB

WCS-12

< SYSTEM DESCRIPTION >

SYSTEM

WARNING CANCEL CONDITIONS

Warning is canceled if any of the following conditions are fulfilled.

SIGNAL PATH

Combination meter sounds integrated buzzer when it judges that parking brake release warning chime is nec-
essary from signals below.

TIMING CHART

SOUND SPECIFICATION

KEY WARNING CHIME

Operation conditions

Ignition switch

ON

Parking brake

During the operation (parking brake switch ON)

Vehicle speed

Approximately 7 km/h (4.3 MPH) or more

Operation conditions

Ignition switch

OFF

Parking brake

Release condition (parking brake switch OFF)

Vehicle speed

Approximately 3 km/h (1.9 MPH) or less

Signal name

Signal path

Ignition switch signal

—

Parking brake switch signal

Parking brake switch

Combination meter

Vehicle speed signal

ABS actuator and electric unit (control unit)

Combination meter

JSNIA2428GB

JSNIA3640GB

WCS

SYSTEM

WCS-13

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

KEY WARNING CHIME : System Diagram

INFOID:0000000006501852

KEY WARNING CHIME : System Description

INFOID:0000000006501853

DESCRIPTION

The warning chime sounds when the ignition switch is in OFF or ACC position with the key inserted and the
driver side door open.

WARNING OPERATION CONDITIONS

The BCM transmits the buzzer output signal to combination meter with CAN communication line when all of
the following operation conditions are met. When combination meter receives buzzer output signal, it sounds
the buzzer.

WARNING CANCEL CONDITIONS

Warning is canceled if any of the following conditions is fulfilled.

SIGNAL PATH

1.

BCM requires warning chime output to combination meter when it judges key warning chime is necessary
from signals below.

2.

Combination meter sounds integrated buzzer, following the warning chime output requirement (below sig-
nal) from BCM.

JSNIA2425GB

Operation conditions

Ignition switch

OFF or ACC position

Key switch

ON (state that inserted key in key
cylinder)

Driver side door

Open [front door switch (driver side)
ON]

Operation conditions

Ignition switch

ON

Key switch

OFF (state that removed key from
key cylinder)

Driver side door

Close [front door switch (driver
side) OFF]

Signal name

Signal path

Ignition switch signal

—

Key switch signal

Key switch

BCM

Driver door switch signal

Front door switch (driver side)

BCM

WCS-14

< SYSTEM DESCRIPTION >

SYSTEM

TIMING CHART

SOUND SPECIFICATION

Signal name

Signal path

Buzzer output signal

BCM

Combination

meter

JSNIA3560GB

JPNIA1774GB

WCS

DIAGNOSIS SYSTEM (COMBINATION METER)

WCS-15

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

DIAGNOSIS SYSTEM (COMBINATION METER)

CONSULT-III Function

INFOID:0000000006502204

CONSULT-III APPLICATION ITEMS

CONSULT-III can perform the following diagnosis modes via CAN communication and the combination meter.

SELF DIAG RESULT

Refer to

MWI-36, "DTC Index"

.

DATA MONITOR

Display Item List

X: Applicable

System

Diagnosis mode

Description

METER/M&A

Self Diagnostic Result

The combination meter checks the conditions and displays memorized errors.

Data Monitor

Displays the combination meter input/output data in real time.

Special function

Lighting history of the warning lamp and indicator lamp can be checked.

Display item [Unit]

MAIN

SIGNALS

Description

SPEED METER
[km/h]

X

Value of vehicle speed signal received from ABS actuator and electric unit (control
unit) via CAN communication.
NOTE:
655.35 is displayed when the malfunction signal is received.

SPEED OUTPUT
[km/h]

X

Vehicle speed signal value transmitted to other units via CAN communication.
NOTE:
655.35 is displayed when the malfunction signal is received.

ODO OUTPUT
[km/h or mph]

Odometer signal value transmitted to other units via CAN communication.

TACHO METER
[rpm]

X

Value of the engine speed signal received from ECM via CAN communication.
NOTE:
8191.875 is displayed when the malfunction signal is received.

FUEL METER
[L]

X

Fuel level indicated on combination meter.

W TEMP METER
[

°

C]

X

Value of engine coolant temperature signal is received from ECM via CAN com-
munication.
NOTE:
215 is displayed when the malfunction signal is input.

FUEL CAP W/L
[Off]

This item is displayed, but cannot be monitored.

ABS W/L
[On/Off]

Status of ABS warning lamp detected from ABS warning lamp signal is received
from ABS actuator and electric unit (control unit) via CAN communication.

VDC/TCS IND
[On/Off]

Status of ESP OFF indicator lamp detected from ESP OFF indicator lamp signal
is received from ABS actuator and electric unit (control unit) via CAN communica-
tion.

SLIP IND
[On/Off]

Status of ESP warning lamp detected from ESP warning lamp signal received
from ABS actuator and electric unit (control unit) via CAN communication.

BRAKE W/L
[On/Off]

Status of brake warning lamp detected from brake warning lamp signal is received
from ABS actuator and electric unit (control unit) via CAN communication.
NOTE:
Displays “Off” if the brake warning lamp is illuminated when the valve check starts,
the parking brake switch is turned ON or the brake fluid level switch is turned ON.

DOOR W/L
[On/Off]

Status of door open warning lamp detected from door switch signal received from
BCM via CAN communication.

HI-BEAM IND
[On/Off]

Status of high beam indicator lamp detected from high beam request signal is re-
ceived from BCM via CAN communication.

WCS-16

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (COMBINATION METER)

TURN IND
[On/Off]

Status of turn indicator lamp detected from turn indicator signal is received from
BCM via CAN communication.

FR FOG IND
[On/Off]

Status of front fog light indicator lamp detected from front fog light request signal
is received from BCM via CAN communication.

RR FOG IND
[On/Off]

Status of rear fog light indicator lamp detected from rear fog light request signal is
received from BCM via CAN communication.

LIGHT IND
[On/Off]

Status of light indicator lamp detected from position light request signal is received
from BCM via CAN communication.

OIL W/L
[On/Off]

• Status of oil pressure warning lamp detected from oil pressure switch signal is

received from BCM via CAN communication. (K9K engine models)

• Status of oil pressure warning lamp detected from oil pressure switch signal is

received from ECM via CAN communication. (except for K9K engine models)

MIL
[On/Off]

Status of malfunction indicator (yellow) detected from malfunctioning indicator
lamp signal is received from ECM via CAN communication.

GLOW IND
[On/Off]

Status of glow indicator lamp detected from glow indicator lamp signal is received
from ECM via CAN communication.

C-ENG2 W/L
[On/Off]

Status of malfunction indicator (red) detected from malfunctioning indicator lamp
signal is received from ECM via CAN communication.

CRUISE IND
[On/Off]

Status of CRUISE indicator lamp detected from ASCD status signal is received
from ECM via CAN communication.

SET IND
[On/Off]

Status of SET indicator lamp detected from ASCD status signal is received from
ECM via CAN communication.

O/D OFF IND
[On/Off]

Status of S mode indicator lamp detected from S mode indicator lamp signal is re-
ceived from TCM via CAN communication.

CVT IND
[On/Off]

Status of CVT indicator lamp detected from CVT status signal is received from
TCM via CAN communication.

4WD W/L
[On/Off]

Status of 4WD warning lamp judged from 4WD warning lamp signal received from
4WD control module with CAN communication line.

4WD LOCK IND
[On/Off]

Status of 4WD lock indicator lamp judged from 4WD mode lamp signal received
from 4WD control module with CAN communication line.

FUEL W/L
[On/Off]

Low fuel warning status detected by the identified fuel level.

KEY G/Y W/L
[On/Off]

Status of KEY warning lamp (G/Y) detected from KEY warning lamp signal is re-
ceived from BCM via CAN communication.

KEY KNOB W/L
[On/Off]

Status of shift P warning lamp detected from shift P warning lamp signal is re-
ceived from BCM via CAN communication.

EPS W/L
[On/Off]

Status of EPS warning lamp detected from EPS warning lamp signal is received
from EPS control unit via CAN communication.

DPF W/L
[On/Off]

Status of Diesel Particulate Filter warning lamp detected from Diesel Particulate
Filter warning lamp signal is received from ECM via CAN communication.

FILTER W/L
[On/Off]

Status of Filter warning lamp detected from Filter warning lamp signal is received
from ECM via CAN communication.

LCD
[B&P N, B&P I, SFT P, BATT, NO KY,

LK WN]

*1

[C&P N, C&P I, SFT P, BATT, NO KY,

LK WN]

*2

Status of engine start operation indicator lamp, shift P warning lamp and KEY
warning lamp, detected from engine start operation indicator lamp signal, shift P
warning lamp signal and KEY warning lamp signal are received from BCM via
CAN communication.

SHIFT IND

[P, R, N, D, L]

*3

[P, R, N, D, M1, M2, M3, M4, M5,

M6]

*4

Status of shift position indicator judged from shift position signal received from
TCM with CAN communication line.

O/D OFF SW
[On/Off]

Status of over drive control switch.

Display item [Unit]

MAIN

SIGNALS

Description

WCS

DIAGNOSIS SYSTEM (COMBINATION METER)

WCS-17

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

• *1: CVT models

• *2: M/T models

• *3: Without manual mode CVT

• *4: With manual mode CVT

NOTE:

Some items are not available according to vehicle specification.

SPECIAL FUNCTION

M RANGE SW
[On/Off]

Status of manual mode switch.

NM RANGE SW
[On/Off]

Status of non-manual mode switch.

AT SFT UP SW
[On/Off]

Status of manual mode shift up switch.

AT SFT DWN SW
[On/Off]

Status of manual mode shift down switch.

COMP F/B SIG
[On/Off]

A/C compressor activation condition that ECM judges according to the engine
coolant temperature and the acceleration degree.

PKB SW
[On/Off]

Status of parking brake switch.

BUCKLE SW
[On/Off]

Status of seat belt buckle switch (driver side).

BRAKE SW
[On/Off]

Status of stop lamp switch.

BRAKE OIL SW
[On/Off]

Status of brake fluid level switch.

A/C AMP CONN
[On/Off]

• Status of A/C auto amp. connection recognition signal.
• Status of PTC heater control unit connection recognition signal.

PASS BUCKLE SW
[On/Off]

Status of seat belt buckle switch (passenger side).

DISTANCE
[km]

Value of distance to empty calculated by combination meter.

OUTSIDE TEMP
[

°

C or

°

F]

Ambient temperature value converted from ambient sensor signal received from
ambient sensor.
NOTE:
This may not match with the temperature value indicated on the information dis-
play. (Because the information display value is a corrected value from the ambient
sensor input value.)

FUEL LOW SIG
[On/Off]

Status of fuel level low warning signal to output to AV control unit via CAN com-
munication.

BUZZER
[On/Off]

X

Buzzer status (in the combination meter) is detected from the buzzer output signal
received from each unit via CAN communication and the warning output condition
of the combination meter.

ASCD SPD BLNK
[On/Off]

Blinking status of ASCD or speed limiter set vehicle speed that is judged by the
ASCD status signal received from ECM via CAN communication.

ASCD STATUS
[Off, ASCD, CRUISE, SL ON, SL
SET]

Display status of ASCD and speed limiter status display judged by the ASCD sta-
tus signal received from ECM via CAN communication.

ASCD REQ SPD
[km/h/Off]

ASCD or speed limiter set vehicle speed value that is judged by the ASCD status
signal received from ECM via CAN communication.

E/O CHG TMNG
[km]

A value of ECM-judged remaining distance to the oil change time.

E/O CHG TMNG RST
[On/Off]

Resetting of a remaining distance to the engine oil change time.

Display item [Unit]

MAIN

SIGNALS

Description

WCS-18

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (COMBINATION METER)

Special menu

W/L ON HISTORY

• Stores histories when warning/indicator lamp is turned on.
• “W/L ON HISTORY” indicates the “TIME” when the warning/ indicator lamp is turned on.
• The “TIME” above is:
- 0: The condition that the warning/indicator lamp has been turned on 1 or more times after starting the engine

and waiting for 30 seconds.

- 1 - 39: The number of times the engine was restarted after the 0 condition.
- NO W/L ON HISTORY: Stores NO (0) turning on history of warning/indicator lamp.
NOTE:
• W/L ON HISTORY is not stored for approximately 30 seconds after the engine starts.
• Brake warning lamp does not store any history when the parking brake is applied or the brake fluid level gets

low.

Display Item

Display item

Description

W/L ON HISTORY

Lighting history of warning lamp and indicator lamp can be checked.

Display item

Description

ABS W/L

Lighting history of ABS warning lamp.

VDC/TCS IND

Lighting history of ESP OFF indicator lamp.

SLIP IND

Lighting history of ESP warning lamp.

BRAKE W/L

Lighting history of brake warning lamp.

DOOR W/L

Lighting history of door open warning.

TRUNK/GLAS-H

This item is displayed, but cannot be monitored.

OIL W/L

Lighting history of oil pressure warning lamp.

C-ENG W/L

Lighting history of malfunction indicator lamp (orange).

C-ENG2 W/L

Lighting history of malfunction indicator lamp (red).

CRUISE IND

Lighting history of CRUISE indicator lamp.

SET IND

Lighting history of SET indicator lamp.

CRUISE W/L

This item is displayed, but cannot be monitored.

BA W/L

This item is displayed, but cannot be monitored.

O/D OFF IND

Lighting history of S mode indicator lamp.

ATC/T-AMT W/L

This item is displayed, but cannot be monitored.

ATF TEMP W/L

This item is displayed, but cannot be monitored.

CVT IND

Lighting history of CVT indicator.

SPORT IND

This item is displayed, but cannot be monitored.

4WD W/L

Lighting history of 4WD warning lamp.

FUEL W/L

Lighting history of low fuel level warning.

WASHER W/L

This item is displayed, but cannot be monitored.

AIR PRES W/L

This item is displayed, but cannot be monitored.

KEY G/Y W/L

Lighting history of KEY warning lamp (G/Y).

KEY R W/L

This item is displayed, but cannot be monitored.

KEY KNOB W/L

Lighting history of Shift P warning lamp.

EPS W/L

Lighting history of EPS warning lamp.

e-4WD

This item is displayed, but cannot be monitored.

AFS OFF IND

This item is displayed, but cannot be monitored.

4WAS/RAS W/L

This item is displayed, but cannot be monitored.

HDC W/L

This item is displayed, but cannot be monitored.

WCS

DIAGNOSIS SYSTEM (COMBINATION METER)

WCS-19

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

SYS FAIL W/L

This item is displayed, but cannot be monitored.

SFT POSI W/L

This item is displayed, but cannot be monitored.

HV BAT W/L

This item is displayed, but cannot be monitored.

HEV BRAKE W/L

This item is displayed, but cannot be monitored.

SFT OPER W/L

This item is displayed, but cannot be monitored.

LANE W/L

This item is displayed, but cannot be monitored.

CHAGE W/L

This item is displayed, but cannot be monitored.

OIL LEV LOW

This item is displayed, but cannot be monitored.

DPF W/L

Lighting history of DPF warning lamp.

TRAILER IND

This item is displayed, but cannot be monitored.

RUN FLAT W/L

This item is displayed, but cannot be monitored.

E-SUS W/L

This item is displayed, but cannot be monitored.

LAUNCH CNT W/L

This item is displayed, but cannot be monitored.

BSW W/L

This item is displayed, but cannot be monitored.

FILTER W/L

Lighting history of FILTER warning lamp.

BRAKE PAD W/L

This item is displayed, but cannot be monitored.

Display item

Description

WCS-20

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

COMMON ITEM

COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)

INFOID:0000000006751933

APPLICATION ITEM

CONSULT-III performs the following functions via CAN communication with BCM.

SYSTEM APPLICATION

BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.

×

: Applicable item

NOTE:

• *1: This item is displayed, but not used.

• *2: For models with automatic A/C, this diagnosis mode is not used.

FREEZE FRAME DATA (FFD)

Diagnosis mode

Function Description

Work Support

Changes the setting for each system function.

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Ecu Identification

The BCM part number is displayed.

Configuration

• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.

System

Sub system selection item

Diagnosis mode

Work Support

Data Monitor

Active Test

Door lock

DOOR LOCK

×

×

×

Rear window defogger

REAR DEFOGGER

×

×

Warning chime

BUZZER

×

×

Interior room lamp timer

INT LAMP

×

×

×

Exterior lamp

HEAD LAMP

×

×

×

Wiper and washer

WIPER

×

×

×

Turn signal and hazard warning lamps

FLASHER

×

×

×

• Automatic A/C
• Manual A/C

AIR CONDITONER

×

×

*

2

• Intelligent Key system
• Engine start system

INTELLIGENT KEY

×

×

×

Combination switch

COMB SW

×

Body control system

BCM

×

NVIS - NATS

IMMU

×

×

×

Interior room lamp battery saver

BATTERY SAVER

×

×

×

Back door open

TRUNK

×

Theft warning alarm

THEFT ALM

×

×

×

—

RETAINED PWR*

1

×

Signal buffer system

SIGNAL BUFFER

×

×

WCS

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

WCS-21

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

The BCM records the following vehicle condition at the time a particular DTC is detected, and displays on
CONSULT-III.

BUZZER

BUZZER : CONSULT-III Function (BCM - BUZZER)

INFOID:0000000006501856

CONSULT-III APPLICATION ITEMS

DATA MONITOR

CONSULT screen item

Indication/Unit

Description

Vehicle Speed

km/h

Vehicle speed of the moment a particular DTC is detected

Odo/Trip Meter

km

Total mileage (Odometer value) of the moment a particular DTC is detected

Vehicle Condition

SLEEP>LOCK

Power position status of
the moment a particular
DTC is detected

While turning BCM status from low power consumption mode to
normal mode (Power supply position is “LOCK”)

SLEEP>OFF

While turning BCM status from low power consumption mode to
normal mode (Power supply position is “OFF”.)

LOCK>ACC

While turning power supply position from “LOCK” to “ACC”

ACC>ON

While turning power supply position from “ACC” to “IGN”

RUN>ACC

While turning power supply position from “RUN” to “ACC” (Vehicle
is stopping and selector lever is except P position.)

CRANK>RUN

While turning power supply position from “CRANKING” to “RUN”
(From cranking up the engine to run it)

RUN>URGENT

While turning power supply position from “RUN“ to “ACC” (Emer-
gency stop operation)

ACC>OFF

While turning power supply position from “ACC” to “OFF”

OFF>LOCK

While turning power supply position from “OFF” to “LOCK”

OFF>ACC

While turning power supply position from “OFF” to “ACC”

ON>CRANK

While turning power supply position from “IGN” to “CRANKING”

OFF>SLEEP

While turning BCM status from normal mode (Power supply posi-
tion is “OFF”.) to low power consumption mode

LOCK>SLEEP

While turning BCM status from normal mode (Power supply posi-
tion is “LOCK”.) to low power consumption mode

LOCK

Power supply position is “LOCK” (Ignition switch OFF with steer-
ing is locked.)

OFF

Power supply position is “OFF” (Ignition switch OFF with steering
is unlocked.)

ACC

Power supply position is “ACC” (Ignition switch ACC)

ON

Power supply position is “IGN” (Ignition switch ON with engine
stopped)

ENGINE RUN

Power supply position is “RUN” (Ignition switch ON with engine
running)

CRANKING

Power supply position is “CRANKING” (At engine cranking)

IGN Counter

0 - 39

The number of times that ignition switch is turned ON after DTC is detected
• The number is 0 when a malfunction is detected now.
• The number increases like 1

→

2

→

3...38

→

39 after returning to the normal condition

whenever ignition switch OFF

→

ON.

• The number is fixed to 39 until the self-diagnosis results are erased if it is over 39.

Test item

Diagnosis mode

Description

BUZZER

Data Monitor

Displays BCM input data in real time.

Active Test

Operation of electrical loads can be checked by sending driving signal to them.

WCS-22

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM) (WITH INTELLIGENT KEY SYSTEM)

ACTIVE TEST

Display item

[Unit]

Description

PUSH SW
[On/Off]

Status of push-button ignition switch judged by BCM.

UNLK SEN-DR
[On/Off]

Status of unlock sensor judged by BCM.

VEH SPEED 1
[km/h]

Value of vehicle speed signal received from combination meter with CAN communication line.

TAIL LAMP SW
[On/Off]

Status of lighting switch judged by BCM using the combination switch readout function.

FR FOG SW
[On/Off]

Status of front fog lamp switch judged by BCM using the combination switch readout function.

DOOR SW-DR
[On/Off]

Status of driver side door switch judged by BCM.

CDL LOCK SW
[On/Off]

Status of door lock unlock switch judged by BCM.

Display item

[Unit]

Description

KEY REMINDER WARN

The key warning chime operation can be checked by operating the relevant function (On/Off).

LIGHT WARN ALM

The light warning chime operation can be checked by operating the relevant function (On/Off).

WCS

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

WCS-23

< SYSTEM DESCRIPTION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

COMMON ITEM

COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM)

INFOID:0000000006751934

APPLICATION ITEM

CONSULT-III performs the following functions via CAN communication with BCM.

SYSTEM APPLICATION

BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for all sub system selection items.

×

: Applicable item

• *1: This item is displayed, but is not used.

• *2: For models with automatic A/C, this mode is not used.

BUZZER

Diagnosis mode

Function Description

Work Support

Changes the setting for each system function.

Self Diagnostic Result

Displays the diagnosis results judged by BCM.

CAN Diag Support Monitor

Monitors the reception status of CAN communication viewed from BCM. Refer to CONSULT-III opera-
tion manual.

Data Monitor

The BCM input/output signals are displayed.

Active Test

The signals used to activate each device are forcibly supplied from BCM.

Ecu Identification

The BCM part number is displayed.

Configuration

• Read and save the vehicle specification.
• Write the vehicle specification when replacing BCM.

System

Sub system selection item

Diagnosis mode

Work Support

Data Monitor

Active Test

Door lock

DOOR LOCK

×

×

×

Rear window defogger

REAR DEFOGGER

×

×

Warning chime

BUZZER

×

×

Interior room lamp control

INT LAMP

×

×

×

Remote keyless entry system

MULTI REMOTE ENT

×

×

×

Exterior lamp

HEAD LAMP

×

×

×

Wiper and washer

WIPER

×

×

×

Turn signal and hazard warning lamps

FLASHER

×

×

• Automatic A/C
• Manual A/C
• Manual heater

AIR CONDITONER

×

×

*

2

Combination switch

COMB SW

×

Body control system

BCM

×

NATS

IMMU

×

×

Interior room lamp battery saver

BATTERY SAVER

×

×

×

Back door open

TRUNK

×

Vehicle security system

THEFT ALM

×

×

×

—

RETAINED PWR*

1

×

×

Signal buffer system

SIGNAL BUFFER

×

×

—

PANIC ALARM*

1

×

WCS-24

< SYSTEM DESCRIPTION >

DIAGNOSIS SYSTEM (BCM) (WITHOUT INTELLIGENT KEY SYSTEM)

BUZZER : CONSULT-III Function (BCM - BUZZER)

INFOID:0000000006501858

CONSULT-III APPLICATION ITEMS

DATA MONITOR

ACTIVE TEST

Test item

Diagnosis mode

Description

BUZZER

Data Monitor

Displays BCM input data in real time.

Active Test

Operation of electrical loads can be checked by sending driving signal to them.

Display item

[Unit]

Description

IGN ON SW
[On/Off]

Status of ignition switch judged by BCM.

KEY ON SW
[On/Off]

Status of key switch judged by BCM.

DOOR SW-DR
[km/h]

Status of driver side door switch judged by BCM.

REVERSE SW CAN
[On/Off]

This item is displayed, but cannot be monitored.

TAIL LAMP SW
[On/Off]

Status of lighting switch judged by BCM using the combination switch readout function.

FR FOG SW
[On/Off]

Status of front fog lamp switch judged by BCM using the combination switch readout function.

BUCKLE SW
[On/Off]

Status of seatbelt buckle switch (driver side) received from combination meter with CAN communica-
tion line.

VEHICLE SPEED
[km/h]

Value of vehicle speed signal received from combination meter with CAN communication line.

Display item

[Unit]

Description

IGN KEY WARN ALM

The key warning chime operation can be checked by operating the relevant function (On/Off).

LIGHT WARN ALM

The light warning chime operation can be checked by operating the relevant function (On/Off).

WCS

COMBINATION METER

WCS-25

< ECU DIAGNOSIS INFORMATION >

C

D

E

F

G

H

I

J

K

L

M

B

A

O

P

ECU DIAGNOSIS INFORMATION

COMBINATION METER

Reference Value

INFOID:0000000006502214

VALUES ON THE DIAGNOSIS TOOL

Monitor Item

Condition

Value/Status

SPEED METER
[km/h]

Ignition switch
ON

While driving

Input value of vehicle speed signal
(CAN communication signal)
NOTE:
655.35 is displayed when the malfunc-
tion signal is received

SPEED OUTPUT
[km/h]

Ignition switch
ON

While driving

Output value of vehicle speed signal
(CAN communication signal)
NOTE:
655.35 is displayed when the malfunc-
tion signal is received

ODO OUTPUT
[km/h or mph]

Ignition switch
ON

—

Output value of odometer signal (CAN
communication signal)

TACHO METER
[rpm]

Ignition switch
ON

Engine running

Input value of engine speed signal
(CAN communication signal)
NOTE:
8191.875 is displayed when the mal-
function signal is received

FUEL METER
[L]

Ignition switch
ON

—

Input value of fuel level sensor signal

W TEMP METER
[

°

C]

Ignition switch
ON

—

Input value of engine coolant tempera-
ture signal (CAN communication sig-
nal)
NOTE:
215 is displayed when the malfunction
signal is input

FUEL CAP W/L

Ignition switch
ON

NOTE:
This item is displayed, but cannot be moni-
tored.

Off

ABS W/L

Ignition switch
ON

ABS warning lamp ON

On

ABS warning lamp OFF

Off

VDC/TCS IND

Ignition switch
ON

ESP OFF indicator lamp ON

On

ESP OFF indicator lamp OFF

Off

SLIP IND

Ignition switch
ON

ESP warning lamp ON

On

ESP warning lamp OFF

Off

BRAKE W/L

Ignition switch
ON

Brake warning lamp ON

On

Brake warning lamp OFF

Off

DOOR W/L

Ignition switch
ON

Door open warning lamp ON

On

Door open warning lamp OFF

Off

HI-BEAM IND

Ignition switch
ON

High-beam indicator lamp ON

On

High-beam indicator lamp OFF

Off

TURN IND

Ignition switch
ON

Turn signal indicator lamp ON

On

Turn signal indicator lamp OFF

Off

FR FOG IND

Ignition switch
ON

Front fog lamp indicator lamp ON

On

Front fog lamp indicator lamp OFF

Off

WCS-26

< ECU DIAGNOSIS INFORMATION >

COMBINATION METER

RR FOG IND

Ignition switch
ON

Rear fog lamp indicator lamp ON

On

Rear fog lamp indicator lamp OFF

Off

LIGHT IND

Ignition switch
ON

Tail lamp indicator lamp ON

On

Tail lamp indicator lamp OFF

Off

OIL W/L

Ignition switch
ON

Oil pressure warning lamp ON

On

Oil pressure warning lamp OFF

Off

MIL

Ignition switch
ON

Malfunction indicator (yellow) ON

On

Malfunction indicator (yellow) OFF

Off

GLOW IND

Ignition switch
ON

Glow indicator lamp ON

On

Glow indicator lamp OFF

Off

C-ENG2 W/L

Ignition switch
ON

Engine warning (red) ON

On

Engine warning (red) OFF

Off

CRUISE IND

Ignition switch
ON

CRUISE indicator lamp ON

On

CRUISE indicator lamp OFF

Off

SET IND

Ignition switch
ON

SET indicator ON

On

SET indicator OFF

Off

O/D OFF IND

Ignition switch
ON

S mode indicator lamp ON

On

S mode indicator lamp OFF

Off

CVT IND

Ignition switch
ON

CVT indicator ON

On

CVT indicator OFF

Off

4WD W/L

Ignition switch
ON

4WD warning lamp ON

On

4WD warning lamp OFF

Off

4WD LOCK IND

Ignition switch
ON

4WD LOCK indicator lamp ON

On

4WD LOCK indicator lamp OFF

Off

KEY G/Y W/L

Ignition switch
ON

During Intelligent Key system malfunction
indication

On

Other than the above

Off

KEY KNOB W/L

Ignition switch
ON

SHIFT P warning lamp ON

On

SHIFT P warning lamp OFF

Off

EPS W/L

Ignition switch
ON

EPS warning lamp ON

On

EPS warning lamp OFF

Off

DPF W/L

Ignition switch
ON

DPF warning lamp ON

On

DPF warning lamp OFF

Off

FUEL W/L

Ignition switch
ON

During low fuel warning indication

On

Other than the above

Off

FILTER W/L

Ignition switch
ON

Filter warning lamp ON

On

Filter warning lamp OFF

Off

Monitor Item

Condition

Value/Status