Juke F15 (2012 year). Service Repair Manual — part 380
TM-512
< SERVICE DATA AND SPECIFICATIONS (SDS)
[CVT: RE0F11A]
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
SERVICE DATA AND SPECIFICATIONS (SDS)
General Specification
INFOID:0000000006487788
*1: Refer to
MA-13, "Fluids and Lubricants"
.
*2: The CVT fluid capacity is the reference value.
Shift Characteristics
INFOID:0000000006487789
Unit: rpm
CAUTION:
Lock-up is engaged at the vehicle speed of approximately 10 km/h (11 MPH) to 90 km/h (56 MPH).
Stall Speed
INFOID:0000000006487790
Engine model
HR16DE
Drive type
2WD
Transaxle model
RE0F11A
Transaxle model code number
3JX4B
Stall torque ratio
1.91 : 1
Pulley ratio
Forward
2.200 – 0.550
Reverse
2.200
Auxiliary gearbox gear ratio
1GR
1.821
2GR
1.000
Reverse
1.714
Counter gear
0.967
Final drive
3.882
Recommended fluid
Genuine NISSAN CVT Fluid NS-2
*1
Fluid capacity
Approx. 7.1 liter (6-1/4 Imp qt)
*2
CAUTION:
• Use only Genuine NISSAN CVT Fluid NS-2. Never mix with other fluid.
• Use only Genuine NISSAN CVT Fluid NS-2. Using transmission fluid other than Genuine NISSAN CVT Fluid NS-2 will dam-
age the CVT, which is not covered by the warranty.
Throttle position
Shift pattern
Engine speed
At 40 km/h (25 MPH)
At 60 km/h (37 MPH)
2/8
“D” position (S mode OFF)
1,300 – 3,100
1,500 – 3,500
“D” position (S mode ON)
1,500 – 3,100
2,400 – 3,500
“L” position
2,800 – 3,600
3,800 – 4,600
ECO mode
1,300 – 2,100
1,500 – 2,300
SPORT mode
1,500 – 3,100
2,400 – 3,500
8/8
“D” position (S mode OFF)
3,900 – 4,700
4,500 – 5,300
“D” position (S mode ON)
3,900 – 4,700
4,500 – 5,300
“L” position
3,900 – 4,700
4,500 – 5,300
ECO mode
3,900 – 4,700
4,500 – 5,300
SPORT mode
3,900 – 4,700
4,500 – 5,300
Stall speed
2,510 – 2,940 rpm
SERVICE DATA AND SPECIFICATIONS (SDS)
TM-513
< SERVICE DATA AND SPECIFICATIONS (SDS)
[CVT: RE0F11A]
C
E
F
G
H
I
J
K
L
M
A
B
TM
N
O
P
Line Pressure
INFOID:0000000006600923
Unit: MPa (bar, kg/cm
2
, psi)
Torque Converter
INFOID:0000000006487791
Shift selector position
Engine speed
Line pressure
“P” and “N”
At idle
0.50 (5.0, 5.1, 72.5)
“R” and “D”
At idle
0.50 (5.0, 5.1, 72.5) – 1.51 (15.1, 15.4, 219)
At stall
4.93 (49.3, 50.3, 714.9) – 5.43 (54.3, 55.4, 787.4)
Distance “A”between the converter housing and torque converter
16.2 mm
VTL-1
VENTILATION, HEATER & AIR CONDITIONER
C
D
E
F
G
H
J
K
L
M
SECTION
VTL
A
B
VTL
N
O
P
CONTENTS
VENTILATION SYSTEM
PRECAUTION . . . . . . . . . . . ...
PRECAUTIONS . . . . . . . . . . . . ...
Precaution Necessary for Steering Wheel Rota-
tion after Battery Disconnect . . . . . . . . .....
PREPARATION . . . . . . . . . . .
PREPARATION . . . . . . . . . . . . ...
Commercial Service Tool . . . . . . . . . . ..
SYSTEM DESCRIPTION . . . . . . . ..
VENTILATION SYSTEM . . . . . . . . . .
System Description . . . . . . . . . . . . ...
REMOVAL AND INSTALLATION . . . .
DUCT AND GRILLE . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . ..
CENTER VENTILATOR GRILLE . . . . . . . ....
CENTER VENTILATOR GRILLE : Removal and
Installation . . . . . . . . . . . . . . . .....
SIDE DEFROSTER NOZZLE . . . . . . . . .
SIDE DEFROSTER NOZZLE : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
SIDE VENTILATOR GRILLE . . . . . . . . . .
SIDE VENTILATOR GRILLE : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
SIDE DEFROSTER GRILLE . . . . . . . . . .
SIDE DEFROSTER GRILLE : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
FRONT DEFROSTER NOZZLE . . . . . . . .
FRONT DEFROSTER NOZZLE : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
CENTER VENTILATOR DUCT . . . . . . . . ..
CENTER VENTILATOR DUCT : Removal and In-
stallation . . . . . . . . . . . . . . . . ..
SIDE VENTILATOR DUCT . . . . . . . . . .
SIDE VENTILATOR DUCT : Removal and Instal-
lation . . . . . . . . . . . . . . . . . .
REAR HEATER DUCT 1 . . . . . . . . . . .
REAR HEATER DUCT 1 : Removal and Installa-
tion . . . . . . . . . . . . . . . . . . ...
REAR HEATER DUCT 2 . . . . . . . . . . .
REAR HEATER DUCT 2 : Removal and Installa-
tion . . . . . . . . . . . . . . . . . . ...
REAR HEATER DUCT 3 . . . . . . . . . . .
REAR HEATER DUCT 3 : Removal and Installa-
tion . . . . . . . . . . . . . . . . . . ...
FOOT DUCT . . . . . . . . . . . . . . . ...
FOOT DUCT : Removal and Installation . . . . .
BLOWER MOTOR . . . . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation (LHD models) . . . . ..
Removal and Installation (RHD models) . . . . .
AIR CONDITIONER FILTER . . . . . . . .
Exploded View . . . . . . . . . . . . . . .
Removal and Installation (LHD models) . . . . ..
Removal and Installation (RHD models) . . . . .
Replacement . . . . . . . . . . . . . . ...
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . .
SERVICE DATA AND SPECIFICATIONS
(SDS) . . . . . . . . . . . . . . . . .
VTL-2
< PRECAUTION >
PRECAUTIONS
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000006753025
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the “SRS AIR BAG” and
“SEAT BELT” of this Service Manual.
The vehicle may be equipped with a passenger air bag deactivation switch. Because no rear seat exists where
a rear-facing child restraint can be placed, the switch is designed to turn off the passenger air bag so that a
rear-facing child restraint can be used in the front passenger seat. The switch is located in the center of the
instrument panel, near the ashtray. When the switch is turned to the ON position, the passenger air bag is
enabled and could inflate for certain types of collision. When the switch is turned to the OFF position, the pas-
senger air bag is disabled and will not inflate. A passenger air bag OFF indicator on the instrument panel lights
up when the passenger air bag is switched OFF. The driver air bag always remains enabled and is not affected
by the passenger air bag deactivation switch.
WARNING:
• To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
• Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the “SRS AIR BAG”.
• Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or har-
ness connectors.
• The vehicle may be equipped with a passenger air bag deactivation switch which can be operated by
the customer. When the passenger air bag is switched OFF, the passenger air bag is disabled and
will not inflate. When the passenger air bag is switched ON, the passenger air bag is enabled and
could inflate for certain types of collision. After SRS maintenance or repair, make sure the passenger
air bag deactivation switch is in the same position (ON or OFF) as when the vehicle arrived for ser-
vice.
PRECAUTIONS WHEN USING POWER TOOLS (AIR OR ELECTRIC) AND HAMMERS
WARNING:
• When working near the Air Bag Diagnosis Sensor Unit or other Air Bag System sensors with the
ignition ON or engine running, DO NOT use air or electric power tools or strike near the sensor(s)
with a hammer. Heavy vibration could activate the sensor(s) and deploy the air bag(s), possibly
causing serious injury.
• When using air or electric power tools or hammers, always switch the ignition OFF, disconnect the
battery, and wait at least 3 minutes before performing any service.
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
INFOID:0000000006753027
NOTE:
• Before removing and installing any control units, first turn the ignition switch to the LOCK position, then dis-
connect both battery cables.
• After finishing work, confirm that all control unit connectors are connected properly, then re-connect both
battery cables.
• Always use CONSULT-III to perform self-diagnosis as a part of each function inspection after finishing work.
If a DTC is detected, perform trouble diagnosis according to self-diagnosis results.
For vehicle with steering lock unit, if the battery is disconnected or discharged, the steering wheel will lock and
cannot be turned.
If turning the steering wheel is required with the battery disconnected or discharged, follow the operation pro-
cedure below before starting the repair operation.
PRECAUTIONS
VTL-3
< PRECAUTION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
OPERATION PROCEDURE
1.
Connect both battery cables.
NOTE:
Supply power using jumper cables if battery is discharged.
2.
Turn the ignition switch to ACC position.
(At this time, the steering lock will be released.)
3.
Disconnect both battery cables. The steering lock will remain released with both battery cables discon-
nected and the steering wheel can be turned.
4.
Perform the necessary repair operation.
5.
When the repair work is completed, re-connect both battery cables. With the brake pedal released, turn
the ignition switch from ACC position to ON position, then to LOCK position. (The steering wheel will lock
when the ignition switch is turned to LOCK position.)
6.
Perform self-diagnosis check of all control units using CONSULT-III.
VTL-4
< PREPARATION >
PREPARATION
PREPARATION
PREPARATION
Commercial Service Tool
INFOID:0000000006485566
Tool name
Description
Remover tool
Remove clips, pawls, and metal clips
JMKIA3050ZZ
VENTILATION SYSTEM
VTL-5
< SYSTEM DESCRIPTION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
SYSTEM DESCRIPTION
VENTILATION SYSTEM
System Description
INFOID:0000000006485567
OUTLINE
Ventilation system is controlled by A/C auto amp. (AUTOMATIC AIR CONDITIONING) or A/C control (MAN-
UAL AIR CONDITIONING and MANUAL HEATER). For details of air conditioner system, refer to
(AUTOMATIC AIR CONDITIONING),
(MANUAL AIR
(MANUAL HEATER).
AIR FLOW
Front
Rear
With rear heater duct
×
: Applicable
Without rear heater duct
JMIIA0869ZZ
JMIIA0870ZZ
MODE/DEF position
indication
AIR OUTRET
Ventilator
Foot
Defroster (4)
Center (1)
Side (2)
Front (3)
Rear (3)
×
×
—
—
—
×
×
×
×
—
—
×
×
×
×
—
×
×
×
×
—
×
—
—
×
VTL-6
< SYSTEM DESCRIPTION >
VENTILATION SYSTEM
MODE/DEF position in-
dication
AIR OUTRET
Ventilator
Foot (3)
Defroster (4)
Center (1)
Side (2)
×
×
—
—
×
×
×
—
—
×
×
×
—
×
×
×
—
×
—
×
DUCT AND GRILLE
VTL-7
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
REMOVAL AND INSTALLATION
DUCT AND GRILLE
Exploded View
INFOID:0000000006485568
FRONT
LHD models
REAR
JMIIA1040ZZ
1.
A/C unit assembly
2.
Side ventilator duct LH
3.
Foot duct LH
4.
Side defroster nozzle LH
5.
Side ventilator grille LH
6.
Side defroster grille LH
7.
Instrument panel assembly
8.
Center ventilator grille LH
9.
Cluster lid C
10. Center ventilator grille RH
11. Side defroster grille RH
12. Side ventilator grille RH
13. Center ventilator duct
14. Front defroster nozzle
15. Instrument panel bracket
16. Side defroster nozzle RH
17. Foot duct RH
18. Side ventilator duct RH
: Pawl
VTL-8
< REMOVAL AND INSTALLATION >
DUCT AND GRILLE
*: Only LHD models for cold areas.
FRONT
1.
A/C unit assembly
2.
Rear heater duct 1 LH*
3.
Rear heater duct 2 LH*
4.
Rear heater duct 3 LH*
5.
Rear heater duct 1 RH*
6.
Rear heater duct 2 RH*
7.
Rear heater duct 3 RH*
: Pawl
JMIIA0838ZZ
DUCT AND GRILLE
VTL-9
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
RHD models
CENTER VENTILATOR GRILLE
CENTER VENTILATOR GRILLE : Removal and Installation
INFOID:0000000006485569
REMOVAL
1.
Remove cluster lid C. Refer to
IP-13, "Removal and Installation"
JMIIA1039ZZ
1.
A/C unit assembly
2.
Side ventilator duct LH
3.
Foot duct LH
4.
Instrument panel bracket
5.
Side defroster nozzle LH
6.
Side ventilator grille LH
7.
Side defroster grille LH
8.
Instrument panel assembly
9.
Center ventilator grille LH
10. Cluster lid C
11. Center ventilator grille RH
12. Side defroster grille RH
13. Side ventilator grille RH
14. Center ventilator duct
15. Front defroster nozzle
16. Side defroster nozzle RH
17. Foot duct RH
18. Side ventilator duct RH
19. Foot duct RH (2WD models)
: Pawl
VTL-10
< REMOVAL AND INSTALLATION >
DUCT AND GRILLE
2.
Remove fixing screws (A).
3.
Disengage fixing pawls (A), and then remove center ventilator
grille from cluster lid C.
INSTALLATION
Install in the reverse order of removal.
SIDE DEFROSTER NOZZLE
SIDE DEFROSTER NOZZLE : Removal and Installation
INFOID:0000000006486706
REMOVAL
Driver side
1.
Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2.
Remove fixing screws (A), and then remove side defroster noz-
zle from instrument panel assembly.
Passenger side
1.
Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2.
Remove fixing screws (A), and then remove instrument panel
bracket (1).
3.
Remove fixing screw (B), and then remove side defroster nozzle
(2) from instrument panel assembly.
JMIIA0839ZZ
JMIIA0840ZZ
JMIIA1042ZZ
JMIIA1041ZZ
DUCT AND GRILLE
VTL-11
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
INSTALLATION
Install in the reverse order of removal.
SIDE VENTILATOR GRILLE
SIDE VENTILATOR GRILLE : Removal and Installation
INFOID:0000000006485570
REMOVAL
1.
Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2.
Remove fixing screws (A), and then remove side ventilator grille
from instrument panel assembly.
INSTALLATION
Install in the reverse order of removal.
SIDE DEFROSTER GRILLE
SIDE DEFROSTER GRILLE : Removal and Installation
INFOID:0000000006486707
REMOVAL
1.
Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2.
Remove side defroster nozzle. Refer to
VTL-10, "SIDE DEFROSTER NOZZLE : Removal and Installa-
3.
Remove fixing screw (A) and disengage fixing pawl (B), and
then remove side defroster grille from instrument panel assem-
bly.
INSTALLATION
Install in the reverse order of removal.
FRONT DEFROSTER NOZZLE
FRONT DEFROSTER NOZZLE : Removal and Installation
INFOID:0000000006486708
REMOVAL
1.
Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2.
Remove side defroster nozzle. Refer to
VTL-10, "SIDE DEFROSTER NOZZLE : Removal and Installa-
JMIIA0845ZZ
JMIIA0846ZZ
VTL-12
< REMOVAL AND INSTALLATION >
DUCT AND GRILLE
3.
Remove fixing screw (A), and then remove front defroster noz-
zle from instrument panel assembly.
INSTALLATION
Install in the reverse order of removal.
CENTER VENTILATOR DUCT
CENTER VENTILATOR DUCT : Removal and Installation
INFOID:0000000006485571
REMOVAL
1.
Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2.
Remove side defroster nozzle (LH and RH). Refer to
VTL-10, "SIDE DEFROSTER NOZZLE : Removal
3.
Remove front defroster nozzle. Refer to
VTL-11, "FRONT DEFROSTER NOZZLE : Removal and Installa-
4.
Remove fixing screws (A), and then remove center ventilator
duct from instrument panel assembly.
INSTALLATION
Install in the reverse order of removal.
SIDE VENTILATOR DUCT
SIDE VENTILATOR DUCT : Removal and Installation
INFOID:0000000006486709
REMOVAL
1.
Remove instrument panel assembly. Refer to
IP-13, "Removal and Installation"
.
2.
Remove fixing screws (A), and then remove side ventilator duct (LH and RH) from the vehicle.
INSTALLATION
Install in the reverse order of removal.
JMIIA0843ZZ
JMIIA1043ZZ
JMIIA0847ZZ
DUCT AND GRILLE
VTL-13
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
J
K
L
M
A
B
VTL
N
O
P
REAR HEATER DUCT 1
REAR HEATER DUCT 1 : Removal and Installation
INFOID:0000000006486715
REMOVAL
1.
Remove center console assembly. Refer to
IP-23, "Removal and Installation"
.
2.
Disengage fixing pawls, and then remove rear heater duct 1 (LH
and RH) from A/C unit assembly.
INSTALLATION
Install in the reverse order of removal.
REAR HEATER DUCT 2
REAR HEATER DUCT 2 : Removal and Installation
INFOID:0000000006486716
REMOVAL
1.
Remove center console assembly. Refer to
IP-23, "Removal and Installation"
.
2.
Remove front seat assmbly. Refer to
SE-19, "Removal and Installation"
.
3.
Remove front kicking plate inner and rear kicking plate inner. Refer to
INT-19, "KICKING PLATE INNER :
.
4.
Remove center pillar lower garnish. Refer to
INT-20, "CENTER PILLAR LOWER GARNISH : Removal
5.
Remove dash side finisher. Refer to
INT-20, "DASH SIDE FINISHER : Removal and Installation"
.
6.
Remove rear heater duct 2.
• Peel off floor carpet (1).
• Remove rear heater duct 3 (2) from rear heater duct 2 (3).
• Remove front floor spacer, and then remove rear heater duct 2
(2) from rear heater duct 1 (1).
INSTALLATION
: Pawl
JMIIA0848ZZ
: Vehicle front
JMIIA0849ZZ
: Vehicle front
JMIIA0850ZZ
VTL-14
< REMOVAL AND INSTALLATION >
DUCT AND GRILLE
Install in the reverse order of removal.
REAR HEATER DUCT 3
REAR HEATER DUCT 3 : Removal and Installation
INFOID:0000000006486717
REMOVAL
1.
Remove center console assembly. Refer to
IP-23, "Removal and Installation"
2.
Remove front seat assmbly. Refer to
SE-19, "Removal and Installation"
.
3.
Remove front kicking plate inner and rear kicking plate inner. Refer to
INT-19, "KICKING PLATE INNER :
.
4.
Remove center pillar lower garnish. Refer to
INT-20, "CENTER PILLAR LOWER GARNISH : Removal
5.
Remove dash side finisher. Refer to
INT-20, "DASH SIDE FINISHER : Removal and Installation"
.
6.
Remove rear heater duct 3.
• Peel off floor carpet (1).
• Remove rear floor spacer, and then remove rear heater duct 3
(2) from rear heater duct 2 (3).
INSTALLATION
Install in the reverse order of removal.
FOOT DUCT
FOOT DUCT : Removal and Installation
INFOID:0000000006485572
REMOVAL
Driver side
1.
Remove instrument lower panel. Refer to
IP-13, "Removal and Installation"
2.
Remove foot duct (LH/RH).
• Disconnect harness connector.
• Remove harness connector mounting clamp.
• Remove fixing screws, and then remove foot duct (LH/RH).
Passenger side
1.
Remove glove box assembly. Refer to
IP-13, "Removal and Installation"
2.
Remove fixing screws, and then remove foot duct (LH/RH).
INSTALLATION
Install in the reverse order of removal.
: Vehicle front
JMIIA0849ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст