Juke F15 (2012 year). Service Repair Manual — part 325
SEC-150
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210E STARTER RELAY
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-34, "Removal and Installation"
NO
>> GO TO 6.
6.
CHECK BCM INPUT SIGNAL CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between IPDM E/R harness connector and BCM harness connector.
3.
Check continuity between transmission range switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 7.
NO
>> Repair or replace harness.
7.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-93, "Removal and Installation"
.
2.
Perform DTC CONFIRMATION PROCEDURE for DTC B210E. Refer to
.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace IPDM E/R. Refer to
PCS-34, "Removal and Installation"
(+)
(–)
Condition
Voltage (V)
(Approx.)
IPDM E/R
Connector
Terminal
E17
69
Ground
Power supply position
OFF
0
ON
12
IPDM E/R
BCM
Continuity
Connector
Terminal
Connector
Terminal
E17
69
M70
101
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E17
69
Not existed
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
SEC-151
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
DTC Logic
INFOID:0000000006628566
DTC DETECTION LOGIC
NOTE:
If DTC B210F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Shift selector lever to the P position.
2.
Turn ignition switch ON and wait 1 second or more.
3.
Shift selector lever to the N position and wait 1 second or more.
4.
Shift selector lever to any position other than P and N, and wait 1 second or more.
5.
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT-III.
Is DTC detected?
YES
>> Go to
SEC-151, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006628567
1.
CHECK DTC OF BCM
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT-III.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK DTC OF TCM
Check DTC in “Self Diagnostic Result” mode of “TCM” using CONSULT-III.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
(CVT:
(CVT: RE0F11A).
NO
>> GO TO 3.
3.
CHECK IPDM E/R SIGNAL CIRCUIT OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Disconnect transmission range switch connector.
4.
Check continuity between IPDM E/R harness connector and transmission range switch harness connec-
tor.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B210F
INTER LOCK/PNP SW ON
There is a difference between P/N position
signal from transmission range switch and
P/N position signal from BCM (CAN).
• Harness or connectors
(CAN communication line is open or
shorted.)
• Harness or connectors
(Transmission range switch circuit
is open or shorted.)
• Transmission range switch
• IPDM E/R
• BCM
IPDM E/R
Transmission range switch
Continuity
Connector
Terminal
Connector
Terminal
E15
48
F23 (HR16DE)
F27 (MR16DDT)
2
Existed
SEC-152
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B210F SHIFT POSITION/CLUTCH INTERLOCK SWITCH
5.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-34, "Removal and Installation"
NO
>> Repair or replace harness.
(+)
(–)
Continuity
IPDM E/R
Connector
Terminal
E15
48
Ground
Not existed
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
SEC-153
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
DTC Logic
INFOID:0000000006628568
DTC DETECTION LOGIC
NOTE:
If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to
DTC CONFIRMATION PROCEDURE
1.
PERFORM DTC CONFIRMATION PROCEDURE
1.
Shift selector lever to the P position.
2.
Turn ignition switch ON and wait 1 second or more.
3.
Shift selector lever to the N position and wait 1 second or more.
4.
Shift selector lever to any position other than P and N, and wait 1 second or more.
5.
Check DTC in “Self Diagnostic Result” mode of “IPDM E/R” using CONSULT-III.
Is DTC detected?
YES
>> Go to
SEC-153, "Diagnosis Procedure"
.
NO
>> INSPECTION END
Diagnosis Procedure
INFOID:0000000006628569
1.
CHECK DTC OF BCM
Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT-III.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
NO
>> GO TO 2.
2.
CHECK DTC OF TCM
Check DTC in “Self Diagnostic Result” mode of “TCM” using CONSULT-III.
Is DTC detected?
YES
>> Perform the trouble diagnosis related to the detected DTC. Refer to
(CVT:
(CVT: RE0F11A).
NO
>> GO TO 3.
3.
CHECK IPDM E/R SIGNAL CIRCUIT OPEN AND SHORT
1.
Turn ignition switch OFF.
2.
Disconnect IPDM E/R connector.
3.
Disconnect transmission range swiwtch connector.
4.
Check continuity between IPDM E/R harness connector and transmission range swiwtch harness connec-
tor.
DTC No.
Trouble diagnosis name
DTC detecting condition
Possible cause
B2110
INTER LOCK/PNP SW OFF
There is a difference between P/N position
signal from transmission range switch and
P/N position signal from BCM (CAN).
• Harness or connectors
(CAN communication line is open or
shorted.)
• Harness or connectors
(Transmission range switch circuit
is open or shorted.)
• Transmission range switch
• IPDM E/R
• BCM
IPDM E/R
Transmission range switch
Continuity
Connector
Terminal
Connector
Terminal
E15
48
F23 (HR16DE)
F27 (MR16DDT)
2
Existed
SEC-154
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
B2110 SHIFT POSITION/CLUTCH INTERLOCK SWITCH
5.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-34, "Removal and Installation"
NO
>> Repair or replace harness.
(+)
(–)
Continuity
IPDM E/R
Connector
Terminal
E15
48
Ground
Not existed
HOOD SWITCH
SEC-155
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
HOOD SWITCH
Component Function Check
INFOID:0000000006628571
1.
CHECK FUNCTION
1.
Select “HOOD SW” in “Data Monitor” mode of “IPDM E/R” using CONSULT-III.
2.
Check “HOOD SW” indication under the following condition.
Is the indication normal?
YES
>> Hood switch is OK.
NO
SEC-155, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000006628572
1.
CHECK HOOD SWITCH SIGNAL CIRCUIT 1
1.
Turn ignition switch OFF.
2.
Disconnect hood switch connector.
3.
Check voltage between hood switch harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK HOOD SWITCH SIGNAL CIRCUIT 2
1.
Disconnect IPDM E/R connector.
2.
Check continuity between IPDM E/R harness connector and hood switch harness connector.
3.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> Replace IPDM E/R. Refer to
PCS-34, "Removal and Installation"
.
NO
>> Repair or replace harness.
3.
CHECK HOOD SWITCH GROUND CIRCUIT
Check continuity between hood switch harness connector and ground.
Monitor item
Condition
Indication
HOOD SW
Hood
Open
ON
Close
OFF
(+)
(–)
Voltage (V)
(Approx.)
Hood switch
Connector
Terminal
E78
1
Ground
12
IPDM E/R
Hood switch
Continuity
Connector
Terminal
Connector
Terminal
E13
32
E78
1
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E13
32
Not existed
Hood switch
Ground
Continuity
Connector
Terminal
E78
2
Existed
SEC-156
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
HOOD SWITCH
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK HOOD SWITCH
SEC-156, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace hood switch.
5.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
>> INSPECTION END
Component Inspection
INFOID:0000000006698782
1.
CHECK HOOD SWITCH
1.
Turn ignition switch OFF.
2.
Disconnect hood switch connector.
3.
Check continuity between hood switch terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace hood switch.
Hood switch
Condition
Continuity
Terminal
1
2
Hood switch
Press
Not existed
Release
Existed
HORN FUNCTION
SEC-157
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
HORN FUNCTION
Component Function Check
INFOID:0000000006628576
1.
CHECK FUNCTION 1
1.
Disconnect vehicle security horn relay.
2.
Perform “VEHICLE SECURITY HORN” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CON-
SULT-III.
3.
Check the horn operation.
Is the operation normal?
YES
>> GO TO 2.
NO
>> Go to
SEC-157, "Diagnosis Procedure"
2.
CHECK FUNCTION 2
1.
Reconnect vehicle security horn relay.
2.
Disconnect horn relay.
3.
Perform “VEHICLE SECURITY HORN” in “ACTIVE TEST” mode of “THEFT ALM” of “BCM” using CON-
SULT-III.
4.
Check the horn operation.
Is the operation normal?
YES
>> INSPECTION END
NO
>> Go to
SEC-157, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000006628577
1.
INSPECTION START
Perform inspection in accordance with procedure that confirms malfunction.
Which procedure confirms malfunction?
Component Function Check 1>>GO TO 2.
Component Function Check 2>>GO TO 4.
2.
CHECK HORN FUNCTION
Check that horn functions properly using horn switch.
Do horns sound?
YES
>> GO TO 3.
NO
>> Check horn circuit. Refer to
3.
CHECK HORN CONTROL CIRCUIT
1.
Disconnect horn relay.
2.
Disconnect IPDM E/R connector.
3.
Check continuity between IPDM E/R harness connector and horn relay harness connector.
4.
Check continuity between IPDM E/R harness connector and ground.
Test item
Description
VEHICLE SECURITY HORN
ON
Horn
Sounds (for 0.5 sec)
Test item
Description
VEHICLE SECURITY HORN
ON
Vehicle security horn
Sounds (for 0.5 sec)
IPDM E/R
Horn relay
Continuity
Connector
Terminal
Connector
Terminal
E13
34
E5
1
Existed
SEC-158
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
HORN FUNCTION
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
4.
CHECK HORN FUNCTION
Check that vehicle security horn functions properly using horn switch.
Do horns sound?
YES
>> GO TO 5.
NO
>> Check vehicle security horn circuit. Refer to
5.
CHECK VEHICLE SECURITY HORN CONTROL CIRCUIT
1.
Disconnect IPDM E/R connector.
2.
Check continuity between IPDM E/R harness connector and vehicle security horn relay harness connec-
tor.
3.
Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 6.
NO
>> Repair or replace harness.
6.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
>> INSPECTION END
IPDM E/R
Ground
Continuity
Connector
Terminal
E13
34
Not existed
IPDM E/R
Vehicle security horn relay
Continuity
Connector
Terminal
Connector
Terminal
E13
34
E56
1
Existed
IPDM E/R
Ground
Continuity
Connector
Terminal
E13
34
Not existed
SECURITY INDICATOR LAMP
SEC-159
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
SECURITY INDICATOR LAMP
Component Function Check
INFOID:0000000006628581
1.
CHECK FUNCTION
1.
Perform “THEFT IND” in “ACTIVE TEST” mode of “IMMU” of “BCM” using CONSULT-III.
2.
Check security indicator lamp operation.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Go to
SEC-159, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000006628582
1.
CHECK SECURITY INDICATOR LAMP POWER SUPPLY CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect combination meter connector.
3.
Check voltage between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO-1
>> Check 10 A fuse [No. 11, located in the fuse block (J/B)].
NO-2
>> Check harness for open or short between combination meter and fuse.
2.
CHECK SECURITY INDICATOR LAMP SIGNAL
1.
Connect combination meter connector.
2.
Disconnect BCM connector.
3.
Check voltage between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 4.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-93, "Removal and Installation"
.
2.
Perform initialization of BCM and registration of all Intelligent Keys using CONSULT-III.
For initialization and registration procedures, refer to CONSULT-III Operation Manual NATS-IVIS/NVIS.
>> INSPECTION END
4.
CHECK SECURITY INDICATOR LAMP CIRCUIT
1.
Disconnect combination meter connector.
2.
Check continuity between combination meter harness connector and BCM harness connector.
Test item
Description
THEFT IND
ON
Security indicator lamp
Illuminates
OFF
Does not illuminate
(+)
(–)
Voltage (V)
(Approx.)
Combination meter
Connector
Terminal
M34
27
Ground
Battery voltage
(+)
(–)
Voltage (V)
(Approx.)
BCM
Connector
Terminal
M68
23
Ground
Battery voltage
SEC-160
< DTC/CIRCUIT DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
SECURITY INDICATOR LAMP
3.
Check continuity between combination meter harness connector and ground.
Is the inspection result normal?
YES
>> Replace combination meter. Refer to
MWI-69, "Removal and Installation"
NO
>> Repair or replace harness.
Combination meter
BCM
Continuity
Connector
Terminal
Connector
Terminal
M34
18
M68
23
Existed
Combination meter
Ground
Continuity
Connector
Terminal
M34
18
Not existed
ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VEHICLE
SEC-161
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
SYMPTOM DIAGNOSIS
ENGINE DOES NOT START WHEN INTELLIGENT KEY IS INSIDE OF VE-
HICLE
Description
INFOID:0000000006628592
Engine does not start when push-button ignition switch is pressed while carrying Intelligent Key.
NOTE:
• Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
• The engine start function, door lock function, power distribution system, and NATS-IVIS/NVIS in the Intelli-
gent Key system are closely related to each other regarding control. The vehicle security function can oper-
ate only when the door lock and power distribution system are operating normally.
Conditions of Vehicle (Operating Conditions)
• “ENGINE START BY I-KEY”: ON
Check the setting of “ENGINE START BY I-KEY” in “Work Support” mode of “INTELLIGENT KEY” of “BCM”
using CONSULT-III.
• One or more of Intelligent Keys with registered Intelligent Key ID are in the vehicle.
Diagnosis Procedure
INFOID:0000000006628593
1.
PERFORM WORK SUPPORT
Perform “INSIDE ANT DIAGNOSIS” in “Work Support” mode of “INTELLIGENT KEY” of BCM using CON-
SULT-III.
Refer to
SEC-26, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY) (With Super
or
SEC-29, "INTELLIGENT KEY : CONSULT-III Function (BCM - INTELLIGENT KEY) (Without Super
.
>> GO TO 2.
2.
PERFORM SELF-DIAGNOSIS RESULT
Perform Self-Diagnosis Result in “BCM”, and check whether or not DTC of inside key antenna is detected.
Is DTC detected?
YES
>> Refer to
NO
>> GO TO 3.
3.
CHECK PUSH-BUTTON IGNITION SWITCH
Check push-button ignition switch.
Refer to
PCS-108, "Component Function Check"
Is the operation normal?
YES
>> GO TO 4.
NO
>> Repair or replace malfunctioning parts.
4.
CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> GO TO 1.
SEC-162
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
STEERING DOES NOT LOCK
STEERING DOES NOT LOCK
Description
INFOID:0000000006628594
Steering does not lock when door is open while ignition switch is OFF.
NOTE:
Before performing the diagnosis, check “Work Flow”. Refer to
Diagnosis Procedure
INFOID:0000000006628595
1.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-87, "Component Function Check"
(With super lock) or
DLK-258, "Component Function Check"
(Without super lock).
Is the inspection normal?
YES
>> GO TO 2.
NO
>> Repair or replace malfunctioning parts.
2.
CHECK DETENTION SWITCH
Check CVT shift selector (detention switch). Refer to
SEC-83, "Component Inspection"
.
Is the inspection normal?
YES
>> GO TO 3.
NO
>> Repair or replace malfunctioning parts.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the inspection normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> GO TO 1.
SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK
SEC-163
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
SECURITY INDICATOR LAMP DOES NOT TURN ON OR BLINK
Description
INFOID:0000000006628596
Security indicator lamp does not blink when ignition switch is in a position other than ON.
NOTE:
• Before performing the diagnosis, check “Work Flow”. Refer to
.
• Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITIONS OF VEHICLE (OPERATING CONDITIONS)
Power supply position is not the ON position.
Diagnosis Procedure
INFOID:0000000006628597
1.
CHECK SECURITY INDICATOR LAMP
Check security indicator lamp.
Refer to
SEC-159, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> GO TO 1.
SEC-164
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
VEHICLE SECURITY SYSTEM CANNOT BE SET
VEHICLE SECURITY SYSTEM CANNOT BE SET
INTELLIGENT KEY
INTELLIGENT KEY : Description
INFOID:0000000006628598
Armed phase is not activated when door is locked using Intelligent Key.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT-III.
INTELLIGENT KEY : Diagnosis Procedure
INFOID:0000000006628599
1.
CHECK INTELLIGENT KEY SYSTEM (REMOTE KEYLESS ENTRY FUNCTION)
Lock/unlock door with Intelligent Key.
Refer to
DLK-28, "DOOR LOCK FUNCTION : System Description"
LOCK FUNCTION : System Description"
(Without super lock).
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check Intelligent Key system (remote keyless entry function). Refer to
DLK-279, "Diagnosis Procedure"
(Without super lock).
2.
CHECK HOOD SWITCH
Check hood switch.
Refer to
SEC-155, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace hood switch.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> GO TO 1.
DOOR REQUEST SWITCH
DOOR REQUEST SWITCH : Description
INFOID:0000000006628600
Armed phase is not activated when door is locked using door request switch.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT-III.
DOOR REQUEST SWITCH : Diagnosis Procedure
INFOID:0000000006628601
1.
CHECK INTELLIGENT KEY SYSTEM (DOOR LOCK FUNCTION)
Lock/unlock door with door request switch.
Refer to
DLK-28, "DOOR LOCK FUNCTION : System Description"
LOCK FUNCTION : System Description"
(Without super lock).
VEHICLE SECURITY SYSTEM CANNOT BE SET
SEC-165
< SYMPTOM DIAGNOSIS >
[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
M
A
B
SEC
N
O
P
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check Intelligent Key system (door lock function). Refer to
SWITCHES : Diagnosis Procedure"
SWITCHES : Diagnosis Procedure"
(Without super lock).
2.
CHECK HOOD SWITCH
Check hood switch.
Refer to
SEC-155, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace hood switch.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> GO TO 1.
UNLOCK SENSOR
UNLOCK SENSOR : Description
INFOID:0000000006691137
Armed phase is not activated when door is locked by door key cylinder operation using mechanical key.
NOTE:
Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATING CONDI-
TIONS)” before starting diagnosis, and check each symptom.
CONDITION OF VEHICLE (OPERATING CONDITIONS)
“SECURITY ALARM SET”: ON
Check the setting of “SECURITY ALARM SET” in “Work Support” mode of “THEFT ALM” of “BCM” using
CONSULT-III.
UNLOCK SENSOR : Diagnosis Procedure
INFOID:0000000006691138
1.
CHECK DOOR LOCK FUNCTION
Lock/unlock door using meahanical key inserted into door key cylinder.
Refer to
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Check Intelligent Key system (remote keyless entry function). Refer to
DLK-275, "Diagnosis Procedure"
(Without super lock).
2.
CHECK HOOD SWITCH
Check hood switch.
Refer to
SEC-155, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace hood switch.
3.
CONFIRM THE OPERATION
Confirm the operation again.
Is the result normal?
YES
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
NO
>> GO TO 1.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст