Juke F15 (2012 year). Service Repair Manual — part 390
WW-84
< REMOVAL AND INSTALLATION >
REAR WIPER ARM
REAR WIPER ARM
Exploded View
INFOID:0000000006479480
Removal and Installation
INFOID:0000000006479481
REMOVAL
1.
Operate rear wiper to the auto stop position.
2.
Remove rear wiper arm cover.
3.
Remove rear wiper arm mounting nut.
4.
Remove wiper arm from the vehicle.
INSTALLATION
1.
Clean wiper arm mount as shown in the figure to prevent nut
from being loosened.
2.
Operate the rear wiper motor to the auto stop position.
3.
Adjust the rear wiper blade position. Refer to
4.
Install the rear wiper arm by tightening the mounting nut.
5.
Inject the washer fluid.
6.
Operate the rear wiper to the auto stop position.
7.
Check that the rear wiper blades stop at the specified position.
8.
Install the rear wiper arm cover.
Adjustment
INFOID:0000000006479482
REAR WIPER BLADE POSITION ADJUSTMENT
1.
Rear wiper motor
2.
Rear wiper blade
3.
Rear wiper arm
4.
Rear wiper arm cover
5.
Rear wiper pivot seal
A
: Model for cold areas
: Pawl
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMLIA1503GB
SKIA0082J
REAR WIPER ARM
WW-85
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Set the wiper blade top on the defrosting wire (A) (clearance between the end of back door glass and the top
of wiper blade center).
Standard clearance
1.
Rear wiper blade
2.
Back door window glass
3.
Back door panel
A
: Rear defogger wire print
L
: 67.5
±
7.5 mm (2.657
±
0.295in)
JMLIA1170ZZ
WW-86
< REMOVAL AND INSTALLATION >
REAR WIPER MOTOR
REAR WIPER MOTOR
Exploded View
INFOID:0000000006645398
Removal and Installation
INFOID:0000000006479484
REMOVAL
1.
Remove rear wiper arm. Refer to
WW-84, "Removal and Installation"
2.
Remove back door lower finisher. Refer to
INT-35, "BACK DOOR LOWER FINISHER : Removal and
.
3.
Disconnect rear wiper motor connector.
4.
Remove rear wiper motor mounting bolts.
5.
Remove rear wiper motor from the vehicle.
6.
Remove the pivot seal.
INSTALLATION
Install in the reverse order of removal.
1.
Rear wiper motor
2.
Rear wiper blade
3.
Rear wiper arm
4.
Rear wiper arm cover
5.
Rear wiper pivot seal
A
: Model for cold areas
: Pawl
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMLIA1503GB
REAR WASHER NOZZLE AND TUBE
WW-87
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
REAR WASHER NOZZLE AND TUBE
Hydraulic Layout
INFOID:0000000006479485
Removal and Installation
INFOID:0000000006479486
REMOVAL
1.
Remove luggage side upper finisher RH. Refer to
INT-32, "LUGGAGE SIDE UPPER FINISHER :
.
2.
Disconnect rear washer tube (2) fixing clip and then remove rear
washer tube joint (2) from rear washer tube.
1.
Rear washer nozzle
2.
Plug
3.
Rear washer tube
4.
Joint
5.
Second washer tube
6.
Back door seal rubber
7.
Front washer tube
: Clip
: Pawl
JMLIA1221ZZ
: Clip
JMLIA1222ZZ
WW-88
< REMOVAL AND INSTALLATION >
REAR WASHER NOZZLE AND TUBE
3.
Fully open back door.
4.
Remove back door seal rubber (2), and then remove rear
washer tube (3) from back door seal rubber.
5.
Remove plug (1).
6.
Disengage rear washer nozzle (1) fixing pawl with a flat-bladed
screwdriver (A) and remove the rear washer nozzle.
CAUTION:
Wrap the flat-bladed screwdriver into a protective tape (B)
to protect the part from damage.
7.
Remove rear washer nozzle from the rear washer tube.
INSTALLATION
Install in the reverse order of removal.
Inspection and Adjustment
INFOID:0000000006479487
INSPECTION
Washer Nozzle Inspection
Check that air can pass through the hose by blowing forward (toward
the nozzle), and check that air cannot pass through by sucking.
ADJUSTMENT
Washer Nozzle Spray Position adjustment
JMLIA1223ZZ
JMLIA1224ZZ
JMLIA1171ZZ
REAR WASHER NOZZLE AND TUBE
WW-89
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Adjust spray positions to match the positions shown in the figure.
Unit: mm (in)
Insert a needle or similar object (A) into the spray opening (1) and
move up/down and left/right to adjust the spray position.
NOTE:
If wax or dust gets into the spray opening of rear washer nozzle (2),
remove wax or dust with a needle or small pin.
1.
Rear washer nozzle
2.
Black print frame line
L: Length
H : Height
φ
: Spray area
122.8 (4.83)
32.8 (1.29)
30 (1.18)
JMLIA1225ZZ
JMLIA1172ZZ
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст