Juke F15 (2012 year). Service Repair Manual — part 389
WW-68
< REMOVAL AND INSTALLATION >
WASHER TANK
5.
Disconnect washer pump connector.
6.
Disconnect headlamp washer pump connector.
7.
Disconnect washer level switch connector.
8.
Disconnect front washer tube and rear washer tube.
9.
Disconnect headlamp washer tube joint.
10. Remove washer tank mounting bolts.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
Add water up to the top of washer tank inlet after installing and check that there is no leakage.
WASHER PUMP
WW-69
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WASHER PUMP
Exploded View
INFOID:0000000006628105
Removal and Installation
INFOID:0000000006479460
REMOVAL
1.
Remove fender protector RH (front). Refer to
EXT-22, "Removal and Installation"
2.
Disconnect washer pump connector.
3.
Disconnect front washer tube and rear washer tube.
4.
Remove washer pump from the washer tank.
5.
Remove packing from washer tank.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Check that there is no leakage after installation or replace packing with new part if it has been dam-
age.
• Never twist the packing when installing the washer pump.
1.
Front washer nozzle LH
2.
Front washer nozzle RH
3.
Front washer tube LH
4.
Front washer tube RH
5.
Check valve
6.
Front washer tube
7.
Joint
8.
Washer tank inlet cap
9.
Washer tank inlet
10. Washer tank
11. Headlamp washer pump
12. Washer pump
13. Packing
14. Rear washer tube
A
: Clip
: Clip
: N·m (kg·m, in-lb)
JMLIA1384GB
WW-70
< REMOVAL AND INSTALLATION >
HEADLAMP WASHER PUMP
HEADLAMP WASHER PUMP
Exploded View
INFOID:0000000006628106
Removal and Installation
INFOID:0000000006479462
REMOVAL
1.
Remove fender protector RH (front). Refer to
EXT-22, "Removal and Installation"
2.
Disconnect headlamp washer pump connector.
3.
Disconnect headlamp washer tube joint.
4.
Remove headlamp washer pump from the washer tank.
5.
Remove the packing from the washer tank.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Check that there is no leakage after installation or replace packing with new part if it has been dam-
age.
• Never twist the packing when installing the headlamp washer pump.
1.
Front washer nozzle LH
2.
Front washer nozzle RH
3.
Front washer tube LH
4.
Front washer tube RH
5.
Check valve
6.
Front washer tube
7.
Joint
8.
Washer tank inlet cap
9.
Washer tank inlet
10. Washer tank
11. Headlamp washer pump
12. Washer pump
13. Packing
14. Rear washer tube
A
: Clip
: Clip
: N·m (kg·m, in-lb)
JMLIA1384GB
WASHER LEVEL SWITCH
WW-71
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WASHER LEVEL SWITCH
Removal and Installation
INFOID:0000000006479463
The washer level switch must be replaced together with the washer tank as an assembly. Refer to
WW-72
< REMOVAL AND INSTALLATION >
FRONT WASHER NOZZLE AND TUBE
FRONT WASHER NOZZLE AND TUBE
Exploded View
INFOID:0000000006479464
LHD models
Hydraulic Layout
INFOID:0000000006479465
Removal and Installation
INFOID:0000000006479466
REMOVAL
1.
Remove cowl top cover. Refer to
EXT-20, "Removal and Installation"
.
JMLIA1385ZZ
1.
Front washer nozzle LH
2.
Front washer nozzle RH
3.
Cowl top cover
4.
Front washer tube (tank side)
5.
Front washer tube RH
6.
Front washer tube LH
: Vehicle front
1.
Front washer nozzle
2.
Check valve
3.
Front washer
4.
Washer tank
: Clip
JMLIA1161ZZ
FRONT WASHER NOZZLE AND TUBE
WW-73
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
2.
Disconnect front washer tube from front washer nozzle.
3.
While pressing pawl (A) on the cowl top cover front side of front
washer nozzle (1), remove front washer nozzle from cowl top
cover.
INSTALLATION
Note the following item, and then install in the reverse order of removal.
CAUTION:
The spray positions differ, check that left and right nozzles are installed correctly.
Inspection and Adjustment
INFOID:0000000006479467
INSPECTION
Check valve Inspection
Check that air can pass through the hose by blowing forward (toward
the nozzle (1)), and check that air cannot pass through by sucking.
ADJUSTMENT
Washer Nozzle Spray Position Adjustment
Adjust spray positions to match the positions shown in the figure.
LHD models
JPLIA0871ZZ
JMLIA1326ZZ
JMLIA1497ZZ
WW-74
< REMOVAL AND INSTALLATION >
FRONT WASHER NOZZLE AND TUBE
Unit: mm (in)
RHD models
Unit: mm (in)
Insert a needle or similar object (A) into the spray opening (1) and
move up/down and left/right to adjust the spray position.
NOTE:
If wax or dust gets into the nozzle, remove wax or dust with a needle
or small pin.
1.
Black printed frame line
: Spray area
: Target spray position
Spray position
H
L
X
Y
S
A
244 (9.61)
350 (13.78)
80 (3.15)
238 (9.37)
78 (3.07)
B
284 (11.18)
93 (3.66)
80 (3.15)
257 (10.12)
89 (3.50)
C
258 (10.16)
70.5 (2.78)
80 (3.15)
255 (10.04)
82 (3.23)
D
309 (12.17)
234 (9.21)
80 (3.15)
312 (12.28)
95 (3.74)
E
235 (9.25)
413 (16.26)
80 (3.15)
295 (11.61)
90 (3.54)
JMLIA1162ZZ
1.
Black printed frame line
: Spray area
: Target spray position
Spray position
H
L
X
Y
S
A
231 (9.09)
359 (14.13)
80 (3.15)
365 (14.37)
155 (6.10)
B
243 (9.57)
116 (4.57)
80 (3.15)
315 (12.40)
120 (4.72)
C
244 (9.61)
107 (4.21)
80 (3.15)
325 (12.80)
130 (5.12)
D
211 (8.31)
342 (13.46)
80 (3.15)
211 (8.31)
100 (3.94)
JPLIA0873ZZ
FRONT WIPER ARM
WW-75
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER ARM
Exploded View
INFOID:0000000006479468
RHD models
LHD models
JMLIA1388GB
1.
Front wiper arm cap
2.
Front wiper arm RH
3.
Front wiper drive assembly
4.
Front wiper motor
5.
Front wiper blade LH
6.
Front wiper arm LH
7.
Front wiper blade RH
: Pawl
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMLIA1387GB
1.
Front wiper arm cap
2.
Front wiper arm LH
3.
Front wiper blade LH
4.
Front wiper arm RH
5.
Front wiper blade RH
6.
Front wiper drive assembly
: Pawl
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
WW-76
< REMOVAL AND INSTALLATION >
FRONT WIPER ARM
Removal and Installation
INFOID:0000000006479469
REMOVAL
1.
Operate front wiper to move it to the auto stop position.
2.
Open the hood.
3.
Disengage front wiper arm cap (1) fixing pawls with a remover
tool (A), and then remove front wiper arm cap from the wiper
arm (2).
4.
Remove front wiper arm mounting nuts.
5.
Raise front wiper arm, and then remove front wiper arm from the vehicle.
INSTALLATION
1.
Clean wiper arm mount as shown in the figure to prevent nuts
from being loosened.
2.
Operate front wiper motor to move the front wiper to the auto
stop position.
3.
Adjust front wiper blade position. Refer to
.
4.
Install front wiper arm by tightening the mounting nuts.
5.
Inject the washer fluid.
6.
Operate front wiper to move it to the auto stop position.
7.
Check that the front wiper blades stop at the specified position.
8.
Install front wiper arm caps.
Adjustment
INFOID:0000000006479470
WIPER BLADE POSITION ADJUSTMENT
Clearance between the end of cowl top cover/ front fender protector and the top of wiper blade center
NOTE:
This figure is for RHD models and is symmetric with LHD models.
: Pawl
: Vehicle front
JMLIA1164ZZ
ELH0717D
JMLIA1167ZZ
FRONT WIPER ARM
WW-77
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
Standard clearance
1.
Front wiper blade RH
2.
Front wiper blade LH
3.
Cowl top cover
4.
Front fender cover
5.
Windshield glass assembly
D
: 37.7
±
7.5 mm (1.484
±
0.295 in)
P
: 46.8
±
7.5 mm (1.843
±
0.295 in)
WW-78
< REMOVAL AND INSTALLATION >
FRONT WIPER BLADE
FRONT WIPER BLADE
Exploded View
INFOID:0000000006479471
Removal and Installation
INFOID:0000000006479472
REMOVAL
Push up the lever (A) of wiper blade (1), while sliding wiper blade
toward the direction of the arrow to remove it from wiper arm (2).
CAUTION:
Be careful not to drop the wiper blade onto the windshield
glass.
INSTALLATION
1.
Install wiper blade into wiper arm.
2.
Install wiper arm.
1.
Wiper blade
2.
Wiper arm
JMLIA1386ZZ
JMLIA1166ZZ
FRONT WIPER DRIVE ASSEMBLY
WW-79
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
FRONT WIPER DRIVE ASSEMBLY
Exploded View
INFOID:0000000006643225
REMOVAL
LHD models
RHD models
JMLIA1387GB
1.
Front wiper arm cap
2.
Front wiper arm LH
3.
Front wiper blade LH
4.
Front wiper arm RH
5.
Front wiper blade RH
6.
Front wiper drive assembly
: Pawl
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMLIA1388GB
1.
Front wiper arm cap
2.
Front wiper arm RH
3.
Front wiper drive assembly
4.
Front wiper motor
5.
Front wiper blade LH
6.
Front wiper arm LH
7.
Front wiper blade RH
: Pawl
WW-80
< REMOVAL AND INSTALLATION >
FRONT WIPER DRIVE ASSEMBLY
DISASSEMBLY
LHD models
RHD models
Removal and Installation
INFOID:0000000006479475
REMOVAL
1.
Remove front wiper arms (LH and RH). Refer to
WW-76, "Removal and Installation"
.
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
JMLIA1498ZZ
1.
Front wiper linkage 1
2.
Shaft seal
3.
Front wiper frame
4.
Front wiper motor
5.
Front wiper linkage 2
6.
Front wiper arm LH
: Nissan MP special grease No.2
JMLIA1168ZZ
1.
Front wiper linkage 1
2.
Shaft seal
3.
Front wiper frame
4.
Front wiper motor
5.
Front wiper linkage 2
6.
Front wiper arm LH
: Nissan MP special grease No.2
FRONT WIPER DRIVE ASSEMBLY
WW-81
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
2.
Remove cowl top cover. Refer to
EXT-20, "Removal and Installation"
.
3.
Disconnect the front wiper motor connector.
4.
Remove the mounting bolts from front wiper drive assembly.
5.
Remove the front wiper drive assembly from the vehicle.
INSTALLATION
1.
Install the front wiper drive assembly to the vehicle.
2.
Connect front wiper motor connector.
3.
Operate front wiper to move it to the auto stop position.
4.
Install cowl top cover. Refer to
EXT-20, "Removal and Installation"
.
5.
Install front wiper arms. Refer to
WW-76, "Removal and Installation"
.
Disassembly and Assembly
INFOID:0000000006479476
DISASSEMBLY
1.
Remove the front wiper linkage 1 and 2 from the front wiper drive assembly.
CAUTION:
Never bend the linkage or damage the plastic part of the ball joint when removing the wiper link-
age.
2.
Remove the front wiper motor mounting screws, and then remove the front wiper motor from the front
wiper frame.
ASSEMBLY
1.
Connect the front wiper motor connector.
2.
Operate the front wiper to move it to the auto stop position.
3.
Disconnect the front wiper motor connector.
4.
Install the front wiper motor to the front wiper frame.
5.
Install the front wiper linkage 2 to the front wiper motor and the front wiper frame.
6.
Install the front wiper linkage 1 to the front wiper frame.
CAUTION:
• Never drop front wiper motor or cause it to come into contact with other parts.
• Be careful for the grease condition at the front wiper motor and front wiper linkage joint
(retainer). Apply Multi
−
purpose grease or an equivalent if necessary.
WW-82
< REMOVAL AND INSTALLATION >
LIGHT & RAIN SENSOR
LIGHT & RAIN SENSOR
Exploded View
INFOID:0000000006479477
Removal and Installation
INFOID:0000000006479478
CAUTION:
When the light & rain sensor is removed from windshield, the light & rain sensor cannot be reused.
REMOVAL
1.
Remove inside mirror assembly. Refer to
MIR-41, "Removal and Installation"
2.
Disconnect light & rain sensor connector.
3.
Disengage both sides fixing pawls, and remove the light & rain sensor from the windshield.
INSTALLATION
Note the following items, and then install in the reverse order of removal.
CAUTION:
• Surface of windshield should be cleaned.
• Never touch gel/adhesive of new part.
1.
Light & rain sensor bracket
2.
Mirror base
3.
Light & rain sensor
4.
Inside mirror assembly
: Pawl
: Do not reuse
JMLIA1389ZZ
WIPER AND WASHER SWITCH
WW-83
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
M
A
B
WW
N
O
P
WIPER AND WASHER SWITCH
Exploded View
INFOID:0000000006479479
The washer level switch must be replaced together with the washer tank as an assembly. Refer to
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст