Juke F15 (2012 year). Service Repair Manual — part 98
DLK-560
< REMOVAL AND INSTALLATION >
[TYPE 4]
HOOD
HOOD SUPPORT ROD : Removal and Installation
INFOID:0000000006600643
REMOVAL
CAUTION:
Two workers are required to support the hood.
1.
Support hood assembly with a suitable material to prevent it from falling.
WARNING:
Injury may occur if hood assembly is not supported by the proper material when removing hood
assembly.
2.
Pull hood support rod from grommet and remove.
INSTALLATION
Install in the reverse order of removal.
RADIATOR CORE SUPPORT
DLK-561
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
RADIATOR CORE SUPPORT
HR16DE
HR16DE : Exploded View
INFOID:0000000006600644
HR16DE : Removal and Installation
INFOID:0000000006600645
RADIATOR CORE SUPPORT UPPER
Removal
1.
Remove front bumper fascia. Refer to
EXT-13, "Removal and Installation"
.
2.
Remove front combination lamp (LH and RH). Refer to
EXL-91, "Removal and Installation"
3.
Remove headlamp (LH and RH). Refer to
EXL-89, "Removal and Installation"
.
4.
Disconnect crash zone sensor harness connector. Refer to
SR-26, "Removal and Installation"
CAUTION:
Turn ignition switch OFF, disconnect battery negative terminal and then wait for at least 3 minutes.
5.
Remove hood lock and hood lock cable fixing clip. Refer to
DLK-587, "HOOD LOCK CONTROL CABLE :
.
6.
Remove horn bracket. Refer to
HRN-4, "Removal and Installation"
7.
Remove air guide (upper) fixing clips, and then remove air guide (upper).
1.
Radiator core support upper
2.
Air guide RH (MT models)
3.
Radiator core support lower
4.
Air guide LH
5.
Air guide (upper)
6.
Air guide LH (CVT models)
7.
Air guide RH (CVT models)
: N·m (kg-m, ft-lb)
JMKIA6021GB
DLK-562
< REMOVAL AND INSTALLATION >
[TYPE 4]
RADIATOR CORE SUPPORT
8.
Remove upper fixing clips (2) of air guide (LH and RH) (1).
9.
Remove hood support rod. Refer to
DLK-560, "HOOD SUPPORT ROD : Removal and Installation"
.
10. Remove mounting bolts, and then remove radiator core support upper.
Installation
Install in the reverse order of removal.
RADIATOR CORE SUPPORT LOWER
Removal
1.
Remove front bumper fascia. Refer to
EXT-13, "Removal and Installation"
.
2.
Remove lower fixing clips (2) of radiator side seal (LH and RH)
(1).
3.
Use belts (A) to suspend radiator and condenser to prevent
them from falling.
CAUTION:
Never damage radiator and condenser.
4.
Remove mounting bolts, and then remove radiator core support lower.
Installation
Install in the reverse order of removal.
MR16DDT
JMKIA5628ZZ
JMKIA5629ZZ
JMKIA5630ZZ
RADIATOR CORE SUPPORT
DLK-563
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
MR16DDT : Exploded View
INFOID:0000000006600646
MR16DDT : Removal and Installation
INFOID:0000000006600647
RADIATOR CORE SUPPORT UPPER
Removal
1.
Remove front bumper fascia. Refer to
EXT-13, "Removal and Installation"
.
2.
Remove front combination lamp (LH and RH). Refer to
EXL-91, "Removal and Installation"
3.
Remove headlamp (LH and RH). Refer to
EXL-89, "Removal and Installation"
.
4.
Disconnect crash zone sensor harness connector. Refer to
SR-26, "Removal and Installation"
CAUTION:
Turn ignition switch OFF, disconnect battery negative terminal and then wait for at least 3 minutes.
5.
Remove hood lock and hood lock cable fixing clip. Refer to
DLK-587, "HOOD LOCK CONTROL CABLE :
.
6.
Remove horn bracket. Refer to
HRN-4, "Removal and Installation"
1.
Radiator core support upper
2.
Air guide RH
3.
Radiator core support lower
4.
Air guide LH
A
: 2WD models
B
: 4WD models
: N·m (kg-m, ft-lb)
JMKIA6022GB
DLK-564
< REMOVAL AND INSTALLATION >
[TYPE 4]
RADIATOR CORE SUPPORT
7.
Remove upper fixing clips (2) of air guide (LH and RH) (1).
8.
Remove hood support rod. Refer to
DLK-560, "HOOD SUPPORT ROD : Removal and Installation"
.
9.
Remove mounting bolts, and then remove radiator core support upper.
Installation
Install in the reverse order of removal.
RADIATOR CORE SUPPORT LOWER
Removal
1.
Remove front bumper fascia. Refer to
EXT-13, "Removal and Installation"
.
2.
Remove lower fixing clips (2) of radiator side seal (LH and RH)
(1).
3.
Using strings (A), hang inlet hose (1) and inlet hose (2) together
with charge air cooler.
CAUTION:
Never damage inlet hoses with charge air cooler.
4.
Support lower side radiator using wooden blocks (B) and a floor
jack (A).
CAUTION:
Never damage radiator.
5.
Remove mounting bolts, and then remove radiator core support lower.
Installation
JMKIA6023ZZ
JMKIA6024ZZ
JMKIA6025ZZ
JMKIA6026ZZ
RADIATOR CORE SUPPORT
DLK-565
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Install in the reverse order of removal.
DLK-566
< REMOVAL AND INSTALLATION >
[TYPE 4]
FRONT FENDER
FRONT FENDER
Exploded View
INFOID:0000000006600648
Removal and Installation
INFOID:0000000006600649
REMOVAL
1.
Remove front fillet molding. Refer to
EXT-26, "FRONT FILLET MOLDING : Removal and Installation"
.
2.
Remove front bumper fascia assembly. Refer to
EXT-13, "Removal and Installation"
3.
Remove sill cover. Refer to
EXT-23, "Removal and Installation"
4.
Remove fender protector. Refer to
EXT-22, "Removal and Installation"
5.
Remove front fender cover. Refer to
6.
Remove front combination lamp. Refer to
EXL-91, "Removal and Installation"
7.
Remove side turn signal lamp. Refer to
EXL-98, "Removal and Installation"
8.
Remove mounting bolts of front fender assembly.
9.
Remove front fender stiffener (2) from the vehicle body while
carefully pulling upper portion of front fender (1) toward vehicle
outside.
10. Remove front fender assembly.
CAUTION:
An viscous urethane foam is installed on the back surface of front fender. When removing the
front fender, be careful to not deform the front fender while performing the procedure and remov-
ing the viscous urethane foam a little at a time.
INSTALLATION
Note the following items, and install in the reverse order of removal.
1.
Front fender assembly
2.
Front fender stiffener
: Vehicle front
JMKIA5632ZZ
: Vehicle front
JMKIA5633ZZ
FRONT FENDER
DLK-567
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
CAUTION:
• After installation, apply the touch-up paint (the body color) onto the head of front fender mounting
bolts.
• After installation, adjust the following part.
- Hood assembly: Refer to
DLK-556, "HOOD ASSEMBLY : Adjustment"
.
- Front door: Refer to
DLK-570, "DOOR ASSEMBLY : Adjustment"
.
DLK-568
< REMOVAL AND INSTALLATION >
[TYPE 4]
FRONT DOOR
FRONT DOOR
Exploded View
INFOID:0000000006628062
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000006628063
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Front door panel
2.
Grommet
3.
TORX bolt
4.
Door striker
5.
Door pad
6.
Bumper rubber
7.
Door check link
8.
Door hinge (lower)
9.
Door hinge (upper)
10. Grommet
: Do not reuse
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Body grease
JMKIA5877GB
FRONT DOOR
DLK-569
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
1.
Disconnect front door harness connector.
2.
Remove mounting bolt of door check link on the vehicle.
3.
Remove door hinge mounting bolts (door side), and then remove door assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check front door open/close, lock/unlock operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, perform the fitting adjustment. Refer to
DLK-570, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
JMKIA5878ZZ
DLK-570
< REMOVAL AND INSTALLATION >
[TYPE 4]
FRONT DOOR
DOOR ASSEMBLY : Adjustment
INFOID:0000000006600652
Check the clearance and surface height between front door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm (in)
FITTING ADJUSTMENT PROCEDURE
1.
Remove front fender. Refer to
DLK-566, "Removal and Installation"
.
2.
Loosen door hinge mounting nuts on door side.
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
TORX bolt
7.
Front door hinge
8.
Rear door hinge (upper)
9.
Rear door hinge (lower)
: Do not reuse
: N·m (kg-m, ft-lb)
: Body grease
Portion
Clearance
Surface height
Front fender – Front door
A – A
3.0 – 5.0 (0.118 – 0.197)
(-1.0) – (+1.0) [(-0.039) – (+0.039)]
Front door – Rear door
B – B
3.3 – 5.3 (0.130 – 0.209)
(-1.0) – (+1.0) [(-0.039) – (+0.039)]
JMKIA5638GB
FRONT DOOR
DLK-571
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
3.
Adjust the surface height of front door according to the fitting standard dimension.
4.
Temporarily tighten door hinge mounting nuts on door side.
5.
Loosen door hinge mounting bolts on body side.
6.
Raise front door at rear end to adjust clearance of the front door according to the fitting standard dimen-
sion.
7.
After adjustment tighten bolts and nuts to the specified torque.
CAUTION:
• After installation, apply touch-up paint (the body color) onto the head of hinge mounting bolts
and nuts.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
8.
Install front fender. Refer to refer to
DLK-566, "Removal and Installation"
.
DOOR STRIKER ADJUSTMENT
Adjust door striker so that it becomes parallel with door lock insertion direction.
DOOR STRIKER
DOOR STRIKER : Removal and Installation
INFOID:0000000006600653
REMOVAL
Remove TORX bolts, and then remove door striker.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Check front door open/close, lock/unlock operation after installation.
• After installation, be sure to perform the fitting adjustment. Refer to
DOOR HINGE
DOOR HINGE : Removal and Installation
INFOID:0000000006600654
REMOVAL
CAUTION:
• Perform work with 2 workers, because of its heavy weight.
• When removing and installing front door assembly, support door with a jack and shop cloth to pro-
tect door and body.
1.
Remove front fender. Refer to
DLK-566, "Removal and Installation"
2.
Remove front door assembly. Refer to
DLK-568, "DOOR ASSEMBLY : Removal and Installation"
.
3.
Remove front door hinge mounting bolts (body side), and then remove front door hinge.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check front door open/close, lock/unlock operation after installation.
• After installation, perform the fitting adjustment. Refer to
DLK-570, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
DLK-572
< REMOVAL AND INSTALLATION >
[TYPE 4]
FRONT DOOR
• Check door hinge rotating part for poor lubrication. If neces-
sary, apply body grease.
DOOR CHECK LINK
DOOR CHECK LINK : Removal and Installation
INFOID:0000000006628064
REMOVAL
1.
Fully close the front door window.
2.
Remove front door finisher. Refer to
INT-13, "Removal and Installation"
3.
Disconnect harness connector of front door speaker.
4.
Remove mounting bolts of front door speaker, and then remove front door speaker.
5.
Remove mounting bolt of door check link on the vehicle.
6.
Remove mounting bolts of door check link on door panel.
7.
Take door check link (1) out from the hole of door panel (2).
INSTALLATION
Note the following item, and install in the reverse order of removal.
CAUTION:
• Check front door open/close operation after installation.
• Check door check link rotating part for poor lubrication. If
necessary, apply grease.
: Grease up point
JMKIA5641ZZ
JMKIA5879ZZ
: Grease up point
JMKIA5642ZZ
REAR DOOR
DLK-573
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REAR DOOR
Exploded View
INFOID:0000000006628065
DOOR ASSEMBLY
DOOR ASSEMBLY : Removal and Installation
INFOID:0000000006628066
CAUTION:
• Perform work with 2 workers, because of it’s heavy weight.
• When removing and installing rear door assembly, support door with a jack and shop cloth to pro-
tect door and body.
REMOVAL
1.
Rear door panel
2.
TORX bolt
3.
Door striker
4.
Door check link
5.
Door hinge (lower)
6.
Door hinge (upper)
: Do not reuse
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
: Body grease
JMKIA5880GB
DLK-574
< REMOVAL AND INSTALLATION >
[TYPE 4]
REAR DOOR
1.
Remove rear door harness grommet (2) from body side outer
(1), and then pull out rear door harness.
2.
Disconnect rear door harness connector.
3.
Remove mounting bolt of door check link on the vehicle.
4.
Remove door hinge mounting bolts (door side), and then remove rear door assembly.
INSTALLATION
Note the following items, and install in the reverse order of removal.
CAUTION:
• Apply anticorrosive agent onto the mounting surface.
• Check rear door open/close, lock/unlock operation after installation.
• Check door hinge rotating part for poor lubrication. If necessary, apply body grease.
• After installation, perform the fitting adjustment. Refer to
DLK-575, "DOOR ASSEMBLY : Adjust-
• After installation, apply touch-up paint (the body color) onto the head of door hinge mounting nuts.
JMKIA5881ZZ
JMKIA5882ZZ
REAR DOOR
DLK-575
< REMOVAL AND INSTALLATION >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR ASSEMBLY : Adjustment
INFOID:0000000006600658
Check the clearance and surface height between front door and each part by visually and touching.
If the clearance and the surface height are out of specification, adjust them according to the procedures
shown below.
Unit: mm (in)
FITTING ADJUSTMENT PROCEDURE
1.
Remove center pillar lower garnish. Refer to
INT-20, "CENTER PILLAR LOWER GARNISH : Removal
1.
Front fender
2.
Front door
3.
Rear door
4.
Body side outer
5.
Door striker
6.
TORX bolt
7.
Front door hinge
8.
Rear door hinge (upper)
9.
Rear door hinge (lower)
: Do not reuse
: N·m (kg-m, ft-lb)
: Body grease
Portion
Clearance
Surface height
Front door – Rear door
B – B
3.3 – 5.3 (0.130 – 0.209)
(-1.0) – (+1.0) [(-0.039) – (+0.039)]
Rear door – Body side outer
C – C
2.6 – 4.6 (0.102 – 0.181)
(-1.0) – (+1.0) [(-0.039) – (+0.039)]
JMKIA5638GB
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст