Juke F15 (2012 year). Service Repair Manual — part 96
DLK-528
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 4]
KEYFOB BATTERY
KEYFOB BATTERY
Component Function Check
INFOID:0000000006616483
1.
CHECK FUNCTION
Check door lock and unlock operation with keyfob button.
Is the inspection result normal?
YES
>> Keyfob is OK.
NO
>> Refer to
DLK-528, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000006616484
1.
CHECK KEYFOB BATTERY
Check by connecting a resistance (approximately 300
Ω
) so that the
current value becomes about 10 mA.
Is the measurement value within the specification?
YES
>> Replace keyfob.
NO
>> Replace keyfob battery. Refer to
.
Standard
: Approx. 2.5 - 3.0 V
OCC0607D
REMOTE KEYLESS ENTRY RECEIVER
DLK-529
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
REMOTE KEYLESS ENTRY RECEIVER
Component Function Check
INFOID:0000000006616485
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “KEYLESS ” or “KEYLESS UNLOCK” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Remote keyless entry receiver is OK.
NO
>> Refer to
DLK-529, "Diagnosis Procedure"
Diagnosis Procedure
INFOID:0000000006616486
1.
CHECK REMOTE KEYLESS ENTRY RECEIVER GROUND CIRCUIT
1.
Turn ignition switch OFF.
2.
Disconnect BCM connector and remote keyless entry receiver connector.
3.
Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
4.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace harness.
2.
CHECK REMOTE KEYLESS ENTRY RECEIVER POWER SUPPLY
1.
Reconnect BCM connector.
2.
Check voltage between remote keyless entry receiver harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> GO TO 3.
3.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 1
1.
Disconnect BCM connector
2.
Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
Monitor item
Condition
Status
KEYLESS LOCK
Keyfob button
LOCK
On
UNLOCK
Off
KEYLESS UNLOCK
LOCK
Off
UNLOCK
On
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M65
18
M73
1
Existed
BCM
Ground
Continuity
Connector
Terminal
M65
18
Not existed
(+)
(–)
Voltage
(Approx.)
Remote keyless entry receiver
Connector
Terminal
M73
4
Ground
5 V
DLK-530
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 4]
REMOTE KEYLESS ENTRY RECEIVER
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-161, "Removal and Installation"
.
NO
>> Repair or replace harness.
4.
CHECK REMOTE KEYLESS ENTRY RECEIVER OUTPUT SIGNAL
1.
Reconnect remote keyless entry receiver connector.
2.
Check signal between remote keyless entry receiver harness connector and ground using oscilloscope.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace remote keyless entry receiver.
5.
CHECK REMOTE KEYLESS ENTRY RECEIVER CIRCUIT 2
1.
Disconnect BCM connector and remote keyless entry receiver connector.
2.
Check continuity between BCM harness connector and remote keyless entry receiver harness connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-161, "Removal and Installation"
.
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M65
19
M73
4
Existed
BCM
Ground
Continuity
Connector
Terminal
M65
19
Not existed
(+)
(–)
Condition
Signal
(Reference value)
Remote keyless entry receiver
Connector
Terminal
M73
2
Ground
Waiting
Press the Intelligent
Key lock or unlock
button
JMKIA3838GB
JMKIA3841GB
BCM
Remote keyless entry receiver
Continuity
Connector
Terminal
Connector
Terminal
M65
20
M73
2
Existed
BCM
Ground
Continuity
Connector
Terminal
M65
20
Not existed
REMOTE KEYLESS ENTRY RECEIVER
DLK-531
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
NO
>> Repair or replace harness.
DLK-532
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 4]
UNLOCK SENSOR
UNLOCK SENSOR
Component Function Check
INFOID:0000000006616495
1.
CHECK FUNCTION
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “LOCK STATUS” in “DATA MONITOR” mode.
3.
Check that the function operates normally according to the following conditions.
Is the inspection result normal?
YES
>> Unlock sensor is OK.
NO
>> Refer to
DLK-532, "Diagnosis Procedure"
.
Diagnosis Procedure
INFOID:0000000006616496
1.
CHECK BCM OUTPUT SIGNAL
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check signal between front door lock assembly (driver side) harness connector and ground using oscillo-
scope.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> GO TO 2.
2.
CHECK UNLOCK SENSOR CIRCUIT
1.
Disconnect BCM connector.
2.
Check continuity between BCM harness connector and front door lock assembly (driver side) harness
connector.
3.
Check continuity between BCM harness connector and ground.
Is the inspection result normal?
YES
>> Replace BCM. Refer to
BCS-161, "Removal and Installation"
.
Monitor item
Condition
Status
LOCK STATUS
Driver side door
Lock
OFF
Unlock
ON
(+)
(–)
Signal
(Reference value)
Front door lock assembly (driver side)
Connector
Terminal
D13
3
Ground
PKIB4960J
BCM
Front door lock assembly (driver side)
Continuity
Connector
Terminal
Connector
Terminal
M65
7
D13
3
Existed
BCM
Ground
Continuity
Connector
Terminal
M65
7
Not existed
UNLOCK SENSOR
DLK-533
< DTC/CIRCUIT DIAGNOSIS >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
NO
>> Repair or replace harness.
3.
CHECK UNLOCK SENSOR GROUND CIRCUIT
Check continuity between front door lock assembly (driver side) harness connector and ground.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace harness.
4.
CHECK UNLOCK SENSOR
DLK-533, "Component Inspection"
.
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Replace front door lock assembly (driver side).
5.
CHECK INTERMITTENT INCIDENT
GI-42, "Intermittent Incident"
.
>> INSPECTION END
Component Inspection
INFOID:0000000006616497
1.
CHECK UNLOCK SENSOR
1.
Turn ignition switch OFF.
2.
Disconnect front door lock assembly (driver side) connector.
3.
Check continuity between front door lock assembly (driver side) terminals.
Is the inspection result normal?
YES
>> INSPECTION END
NO
>> Replace front lock assembly (driver side).
Front door lock assembly (driver side)
Ground
Continuity
Connector
Terminal
D13
4
Existed
Front door lock assembly (driver side)
Condition
Continuity
Terminal
3
4
Driver side door
Unlock
Existed
Lock
Not existed
DLK-534
< SYMPTOM DIAGNOSIS >
[TYPE 4]
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
SYMPTOM DIAGNOSIS
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK
SWITCH
ALL DOOR
ALL DOOR : Description
INFOID:0000000006619157
All doors do not lock/unlock using door lock and unlock switch.
ALL DOOR : Diagnosis Procedure
INFOID:0000000006619158
1.
CHECK DOOR LOCK AND UNLOCK SWITCH
Check door lock and unlock switch.
Refer to
DLK-520, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK DOOR LOCK ACTUATOR
Check front door lock assembly (driver side).
Refer to
DLK-515, "DRIVER SIDE : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK DOOR SWITCH
Check door switch.
Refer to
DLK-397, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
CHECK KEY SWITCH
Check key switch. Refer to
DLK-401, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-161, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
DRIVER SIDE
DRIVER SIDE : Description
INFOID:0000000006619159
Driver side door does not lock/unlock using door lock and unlock switch.
DRIVER SIDE : Diagnosis Procedure
INFOID:0000000006619160
1.
CHECK DOOR LOCK ACTUATOR
Check front door lock assembly (driver side).
Refer to
DLK-515, "DRIVER SIDE : Component Function Check"
.
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
DLK-535
< SYMPTOM DIAGNOSIS >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-161, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
PASSENGER SIDE
PASSENGER SIDE : Description
INFOID:0000000006619161
Passenger side door does not lock/unlock using door lock and unlock switch.
PASSENGER SIDE : Diagnosis Procedure
INFOID:0000000006619162
1.
CHECK DOOR LOCK ACTUATOR
Check front door lock assembly (passenger side).
Refer to
DLK-516, "PASSENGER SIDE : Component Function Check"
.
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-161, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
REAR LH
REAR LH : Description
INFOID:0000000006619163
Rear LH side door does not lock/unlock using door lock and unlock switch.
REAR LH : Diagnosis Procedure
INFOID:0000000006619164
1.
CHECK DOOR LOCK ACTUATOR
Check rear door lock assembly LH.
Refer to
DLK-517, "REAR LH : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-161, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
REAR RH
REAR RH : Description
INFOID:0000000006619165
Rear RH side door does not lock/unlock using door lock and unlock switch.
DLK-536
< SYMPTOM DIAGNOSIS >
[TYPE 4]
DOOR DOES NOT LOCK/UNLOCK WITH DOOR LOCK AND UNLOCK SWITCH
REAR RH : Diagnosis Procedure
INFOID:0000000006619166
1.
CHECK DOOR LOCK ACTUATOR
Check rear door lock assembly RH
Refer to
DLK-518, "REAR RH : Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-161, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
DOOR DOES NOT LOCK/UNLOCK WITH DRIVER SIDE DOOR LOCK KNOB OR
DOOR KEY CYLINDER
DLK-537
< SYMPTOM DIAGNOSIS >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
DOOR DOES NOT LOCK/UNLOCK WITH DRIVER SIDE DOOR LOCK
KNOB OR DOOR KEY CYLINDER
Diagnosis Procedure
INFOID:0000000006619156
1.
CHECK POWER DOOR LOCK OPERATION
Check power door lock operation.
Does door lock/unlock with door lock and unlock switch?
YES
>> GO TO 2.
NO
>> Go to
DLK-534, "ALL DOOR : Diagnosis Procedure"
.
2.
CHECK UNLOCK SENSOR
Check unlock sensor.
Refer to
DLK-532, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-161, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
DLK-538
< SYMPTOM DIAGNOSIS >
[TYPE 4]
DOOR DOES NOT LOCK/UNLOCK WITH KEYFOB
DOOR DOES NOT LOCK/UNLOCK WITH KEYFOB
Diagnosis Procedure
INFOID:0000000006619167
1.
CHECK POWER DOOR LOCK OPERATION
Check power door lock operation.
Does door lock/unlock with door lock and unlock switch?
YES
>> GO TO 2.
NO
>> Go to
DLK-534, "ALL DOOR : Diagnosis Procedure"
.
2.
CHECK REMOTE KEYLESS ENTRY RECEIVER
Check remote keyless entry receiver.
Refer to
DLK-529, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK KEYFOB BATTERY
Check keyfob battery.
Refer to
DLK-528, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-161, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
BACK DOOR DOES NOT OPENED
DLK-539
< SYMPTOM DIAGNOSIS >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
BACK DOOR DOES NOT OPENED
Diagnosis Procedure
INFOID:0000000006619155
1.
CHECK BACK DOOR OPENER SWITCH
Check back door opener switch.
Refer to
DLK-513, "Component Function Check"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Repair or replace the malfunctioning parts.
2.
CHECK BACK DOOR OPENER ACTUATOR
Check back door opener actuator.
Refer to
DLK-512, "Diagnosis Procedure"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Repair or replace the malfunctioning parts.
3.
CHECK VEHICLE SPEED SIGNAL
Check vehicle speed signal.
Refer to
.
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Repair or replace the malfunctioning parts.
4.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-161, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
DLK-540
< SYMPTOM DIAGNOSIS >
[TYPE 4]
ANTI-HIJACK FUNCTION DOES NOT OPERATE
ANTI-HIJACK FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000006619153
1.
CHECK “DOOR LOCK–UNLOCK SET” SETTING IN “WORK SUPPORT”
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “DOOR LOCK-UNLOCK SET” in “WORK SUPPORT” mode.
3.
Check “DOOR LOCK-UNLOCK SET” in “WORK SUPPORT”
Refer to
DLK-501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"
Is the inspection result normal?
YES
>> GO TO 2
NO
>> Set “DOOR LOCK-UNLOCK SET” in “WORK SUPPORT”
2.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-161, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
VEHICLE SPEED SENSING AUTO LOCK OPERATION DOES NOT OPERATE
DLK-541
< SYMPTOM DIAGNOSIS >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
VEHICLE SPEED SENSING AUTO LOCK OPERATION DOES NOT OPER-
ATE
Diagnosis Procedure
INFOID:0000000006619180
1.
CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.
3.
Check “AUTOMATIC LOCK/UNLOCK SELECT” setting in “WORK SUPPORT”.
Refer to
DLK-501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set “Lock Only” or “Lock/Unlock” in “WORK SUPPORT”.
2.
CHECK “AUTOMATIC DOOR LOCK SELECT” SETTING IN “WORK SUPPORT”
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT” mode.
3.
Check “AUTOMATIC DOOR LOCK SELECT” setting in “WORK SUPPORT”.
Refer to
DLK-501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “VH SPD” in “AUTOMATIC DOOR LOCK SELECT”.
3.
REPLACE BCM
• Replace BCM. Refer to
BCS-161, "Removal and Installation"
• Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
DLK-542
< SYMPTOM DIAGNOSIS >
[TYPE 4]
IGN OFF INTERLOCK DOOR UNLOCK FUNCTION DOES NOT OPERATE
IGN OFF INTERLOCK DOOR UNLOCK FUNCTION DOES NOT OPERATE
Diagnosis Procedure
INFOID:0000000006619170
1.
CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.
3.
Check “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.
Refer to
DLK-501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT”.
2.
CHECK “AUTOMATIC DOOR UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT” mode.
3.
Check “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.
Refer to
DLK-501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT”.
3.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-161, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OPER-
ATE
DLK-543
< SYMPTOM DIAGNOSIS >
[TYPE 4]
C
D
E
F
G
H
I
J
L
M
A
B
DLK
N
O
P
P RANGE INTERLOCK DOOR LOCK/UNLOCK FUNCTION DOES NOT OP-
ERATE
Diagnosis Procedure
INFOID:0000000006619173
1.
CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.
3.
Check “AUTOMATIC LOCK/UNLOCK SELECT” setting in “WORK SUPPORT”.
Refer to
DLK-501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"
Is the inspection result normal?
YES
>> GO TO 2.
NO
>> Set “Unlock Only”, “Lock Only” or “Lock/Unlock” in “AUTOMATIC LOCK/UNLOCK SELECT”.
2.
CHECK “AUTOMATIC DOOR LOCK SELECT” SETTING IN “WORK SUPPORT”
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT” mode.
3.
Check “AUTOMATIC DOOR LOCK SELECT” setting in “WORK SUPPORT”.
Refer to
DLK-501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"
Is the inspection result normal?
YES
>> GO TO 3.
NO
>> Set “P RANGE” in “AUTOMATIC DOOR LOCK SELECT”.
3.
CHECK “AUTOMATIC DOOR UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1.
Select “DOOR LOCK” of “BCM” using CONSULT-III.
2.
Select “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT” mode.
3.
Check “AUTOMATIC DOOR UNLOCK SELECT” setting in “WORK SUPPORT”.
Refer to
DLK-501, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (Without Super Lock)"
Is the inspection result normal?
YES
>> GO TO 4.
NO
>> Set “MODE 2” or “MODE 4” in “AUTOMATIC DOOR UNLOCK SELECT”.
4.
CHECK TCM
Check TCM for DTC.
Refer to
(RE0F10B models) or
(RE0F11A models).
Is the inspection result normal?
YES
>> GO TO 5.
NO
>> Repair or replace the malfunctioning parts.
5.
REPLACE BCM
1.
Replace BCM. Refer to
BCS-161, "Removal and Installation"
.
2.
Confirm the operation after replacement.
Is the result normal?
YES
>> INSPECTION END
NO
>> Check intermittent incident. Refer to
GI-42, "Intermittent Incident"
.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст